• 대한화학회지
• /
• 제15권6호
• /
• pp.285-293
• /
• 1971

The statistical thermodynamical properties of heavy water are calculated according to the transient state theory of significant liquid structure. The calculated values are shown to be in good agreement with the observed ones. The grand canonical ensemble partition function for the adsorbed phase of heavy water on graphite surface is derived using the theory. The adsorption isotherm, the surface pressure, the molar entropy and the molar internal energy for the adsorbed phase and then the molar heat of adsorption are calculated according to the derived partition function. The thermodynamic properties of the adsorbed water are also calculated and the results are compared with those of heavy water and discussed in view of the experimentally observed phenomena.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2006년도 특별논문집
• /
• pp.34-39
• /
• 2006

In rough seas, water breaker of the sea-going ships is subject to high impact loads due to the green water and some ships' water breaker suffers structure damage. So, a substantial research on the structural response caused by green water impact is required. In this paper, the green water flow on bow deck is simulated by FDM(finite differential method). Using the results of green water simulation, impact loads on water breaker are calculated. Calculation results of the 6200TEU container ship's structural response to this green water impact pressure are shown and discussed for two condiered calculation conditions.

• Safety and Health at Work
• /
• 제8권2호
• /
• pp.226-230
• /
• 2017

The performance of sound barriers was evaluated to determine their technical effectiveness and practicality in reducing noise exposures to operating engineers in construction. Commercially purchased sound dampening mats (SDMats) were installed inside three heavy-equipment engine compartments. Sound pressure levels (SPLs) were measured before and after installing the SDMats while the equipment was on idle and full-throttle settings where it normally operates. SPLs inside the heavy-equipment operator cabs were significantly reduced by 5.6-7.6 dBA on the full-throttle setting following installation of the SDMats (p < 0.01). The evaluated engineering control intervention was simple to install, affordable, and substantially reduced the engine noise reaching the heavy-equipment operator, potentially reducing reliance on hearing-protection devices to protect construction workers from noise exposures.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1330-1331
• /
• 2008

MCCB와 같은 저압차단기는 접점사이에서 발생한 아크를 금속의 소호그리드로 유입하여 아크를 소호하게 된다. 일반적으로 고장 전류 차단시에 저압차단기에서 발생한 아크는 고압.고열이므로 아크에너지에 의해 소호부의 압력이 크게 상승하게 되며 압력에 의해 아크의 거동은 큰 영향을 받게 되므로 아크 구동력의 증가를 위해서는 압력에 의해 아크거동이 어떠한 영향을 받는지에 대한 정보가 필요하다. 본 연구에서는 압력파의 영향을 명확하게 하고 다른 요소에 의한 영향을 배제하여 압력파와 아크거동간의 상호작용만을 실험하기 위해 시험용 소호부를 고안하여 시험용 소호부에서 아크의 압력과 거동을 측정.분석하여 아크거동과 압력파의 관계를 연구하였다.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2008년도 특별논문집
• /
• pp.76-83
• /
• 2008

New and more efficient propulsion systems are required for LNG carriers. One of the proposed systems is a combination of a gas turbine with a heat recovery steam generator. This system constitutes a novel approach, which needs to be analyzed by system analysis and risk assessment to compensate for the lack of field experience. Of specific concern is the high pressure fuel supply system. This paper describes the dispersion and fire analysis performed to identify for safety and design improvement of proposed system.

• 대기
• /
• 제23권2호
• /
• pp.161-169
• /
• 2013

We examine the effects of the sea surface temperature (SST) distribution on heavy snowfall over the Yellow Sea using high-resolution SST products and WRF (Weather Research and Forecasting) model simulations in 30 December 2010. First, we evaluate the model by comparing the simulated and observed fresh snowfall over the Korean peninsula (Ho-Nam province). The comparison shows that the model reproduces the distributions and magnitudes of the observed snowfall. We then conduct sensitivity model simulations where SST perturbations by ${\pm}1.1^{\circ}C$ relative to baseline SST values (averaged SST for $5{\sim}15^{\circ}C$) are uniformly specified over the region of interest. Results show that ${\pm}1.1^{\circ}C$ SST perturbation simulations result in changes of air temperature by $+0.37/-0.38^{\circ}C$, and by ${\pm}0.31^{\circ}C$ hPa for sea level pressure, respectively, relative to the baseline simulation. Atmospheric responses to SST perturbations are found to be relatively linear. The changes in SST appear to perturb precipitation variability accounting for 10% of snow and graupel, and 18% of snowfall over the Yellow Sea and Ho- Nam province, respectively. We find that anomalies of air temperature, pressure, and hydrometeors due to SST perturbation propagate to the upper part of cloud top up to 500 hPa and show symmetric responses with respect to SST changes.

• 한국전산유체공학회지
• /
• 제17권2호
• /
• pp.21-27
• /
• 2012

Reynolds-averaged Navier-Stokes equations solver based on a pressure-based cell-centered finite volume method was developed using OpenFOAM libraries, which was an open source and providing computational continuum mechanics libraries. For the reasonable development of the turbulent boundary layer on the bow of the ship, specified library was developed. Grid sensitivities, such as skewness and aspect ratio of a cell, were tested for the solution convergence. Pressure, turbulent kinetic energy, turbulent dissipation rate contours on the ship surface computed by the developed CFD code were compared with those computed by the commercial CFD code, Fluent.

• 한국정밀공학회지
• /
• 제19권1호
• /
• pp.204-211
• /
• 2002

Today\`s industrialized plants are required to reduce SOx emitted from stacks at factories, utility power stations, etc. For this purpose, flue gas desulfurization(FGD) system is installed in thermal power plant and gas-gas heater(GGH) is used to play a vital role to reheat the wet treated gas from FGD. The sector plates are located at cold and hot sides of gas-gas heater. They serve as sealing to prevent mixing treated and untreated gases. Therefore, the deformation of the sector plate due to its dead weight and gas pressure should be considered as major factor for the sector plate design. And finite element analysis(FEA) for rotor part in GGH is performed with original model and two weight-reduced models with different diaphragm thickness, respectively. Stress concentrations at rotor diaphragm happen due to the dead weight, pressure difference between treated and untreated gas, and thermal distribution in the rotor. As the thickness of diaphragm is decreased, the stress level is increased. The direction of treated gas and untreated gas flow may affect the stress level.

• Journal of Ship and Ocean Technology
• /
• 제8권1호
• /
• pp.42-50
• /
• 2004

In these ten years, the cavitation and erosion phenomena in the rudder have been increased for high-speed container ships. The cavitation in the rudder blades which is injurious to rudder efficiency is mainly caused by the main flow with a large angle of attack induced by propellers, and the erosion which occurs as a result of repeated blows by shock wave that cavitation collapse may produce was observed in the gap legion of the rudder. However, gap cavitation is not prone to occur in model experiments because of low Reynolds number. So, the viscous effect should be considered for solving the flow of the narrow gap. In order to predict the cavitation phenomena and to improve the performance of the rudder, the analysis of the viscous flow in the rudder gap is positively necessary. In this study, numerical calculation for the solution of the RANS equation is applied to the two-dimensional flow around the rudder gap including horn part and pintle part. The velocity and pressure field are numerically acquired according to Reynolds number and the case that the round bar is installed in the gap is analyzed. For reduced the acceleration that pressure drop can be highly restrained numerically and in model experiment, the cavitation bubbles can be reduced.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.115-122
• /
• 2006

EGR system has been widely used to reduce NOx emission in light duty diesel engines, but its application to heavy duty diesel engine is not common yet. In this study, simulation model for EURO-3 engine was developed using commercial code WAVE and then verified by comparison with experimental results in performance and emission. Possibility to meet EURO-4 regulation using modified EURO-3 engine with LPL EGR system was studied. Each components of the engine was modeled using CATIA and WaveMesher. The engine test mode was ESC 13 and injection timing and quantity were changed to compensate engine performances, because applying EGR causes power reduction. As a results of the simulation, it was found that EURO-4 NOx regulation could be achieved by applying LPL EGR system to current EURO-3 engine even with some BSFC deterioration.