• Journal of the Korea Organic Resources Recycling Association
• /
• v.26 no.1
• /
• pp.29-37
• /
• 2018

In this study, optimum extraction conditions for phosphorus recovery from sewage sludge ash(SSA) were investigated. For this purpose, an experiment was conducted to determine optimal recovery conditions for Ca-P type phosphorus by using calcium component in the recycled aggregate residue. The phosphorus content of sewage sludge ash was confirmed to be 5.0 %. When $H_2SO_4$ was used as an extract, concentration of 1 N $H_2SO_4$, L/S ratio of 10, and extraction time of 30 min were found to be the optimal extraction conditions. Phosphorus was extracted by using optimal extraction conditions, and then the heavy metals eluted with phosphorus were removed using 1~20 g of cation exchange resin. In 20 g of cation exchange resin, Fe 71.3%, Cu 82.4%, Zn 79.9%, and Cr 15% were removed. After that, the mixing ratio of the calcium extract obtained from the recycled aggregate residue (RAR) was changed to 1:1, 1:5, 1:10. The pH of the SSA to RAR mixture was adjusted to 2, 4, 8 and 12 by the addition of 5 N NaOH to the mixture of 1:5, and the phosphorus was recovered as Ca-P type precipitate. The optimum pH was 8. When recycled aggregate residues were used, the weight of calcium phosphate increased, but the amount of wastewater generated also increased. Therefore, it was concluded that the use of recycled aggregate residue was not economically feasible.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.7
• /
• pp.488-494
• /
• 2012

This study was conducted to determine the optimal ratio of sludges from milk processing industry (MPS), paper-mill industry (PMS) and night-soil treatment plant (NSS) for vermicomposting. Five different ratios, 0 : 80 : 20 (MPS-0), 25 : 60 : 15 (MPS-25), 50 : 40 : 10 (MPS-50), 75 : 20 : 5 (MPS-75), and 100 : 0 : 0 (MPS-100 : control) MPS : PMS : NSS by wet weight were tested in a small plot experiment. The experiment for each mixing ratio was performed for 2 weeks with the three replications. MPS-100 (100 : 0 : 0) only had the highest decomposition rate with 19.9%, followed by MPS-25, MPS-50, MPS-75 and MPS-0 with 19.5, 19.1, 17.6 and 16.7%, respectively. Except for MPS-100, Vermicomposting resulted in increase in ash, T-P, $NO_2{^-}-N$, $NO_3{^-}-N$, Mg, K, As, Cd and Cu, whereas moisture, VS (Volatile Substance), TKN (Total Kjeldahl Nitrogen), $NH_4{^+}-N$, Ca, Hg and Pb were lower in the final cast than the initial feed mixture. Meanwhile Zn showed very slight difference and Cr and Ni did not show any tendency between the feed mixture and the final cast. In the case of MPS-100, where the decomposition rate was the highest, all the heavy metals in the final cast except for Hg were increased. All the vermicomposts produced from five different mixing ratios of the vermicomposting sludges met the Korea Standard as by-product compost.

• Journal of the Mineralogical Society of Korea
• /
• v.30 no.1
• /
• pp.21-29
• /
• 2017

Surface soils on Barton Peninsula, King George Island, West Antarctica were investigated to acquire the mineralogical and geochemical data of soil in Antarctica. Multiline of techniques for example, X-ray diffraction (XRD), transmission electron microscopy (TEM)-electron energy loss spectroscopy (EELS), and wet chemistry analysis were performed to measure the composition of clay minerals, Fe-oxidation states, cation exchange capacity, and total cation concentration. Various minerals in sediments such as smectite, illite, chlorite, kaolinite, quartz and plagioclase were identified by XRD. Fe-oxidation states of bulk soils showed 20-40% of Fe(II) which would be ascribed to the reduction of Fe in clays as well as Fe-bearing minerals. Moreover, redox states of Fe in smectite structure was a ~57% of Fe(III) consistent to the values for the bulk soils. The cation exchange capacity of bulk soils ranged from 100 to 300 meq/kg and differences were not significantly measured for the sampling locations. Total cations (Mg, K, Na, Al, Fe) of bulk soils varies, contrast to the heavy metals (Co, Ni, Cu, Zn, Mn). These results suggested that composition of bed rocks influenced the distribution of elements in soil environments and soils containing clay compositions may went through the bio/geochemical alteration.

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.131-137
• /
• 2010

The stormwater runoff from rest areas in highways are known as more polluted compared to highways because of more vehicle activities. This study is performed to find pollutant characteristics in the rest areas in the magnitude of statistical pollutant concentrations during storms. Washoff characteristics of pollutants from rest areas by monitoring of rainfall, runoff rate and runoff samples were evaluated. High concentrations of pollutants in runoff were observed at the beginning of runoff and rapid decrease thereafter, indicating that first-flush effects are clearly occurred. Event Mean Concentrations(EMCs) of TSS, COD, TN, and TP are estimated to be in the range of 31.04-127.11mg/L, 35.5-369.5mg/L, 2.62-9.86 mg/L, and 0.53-1.96mg/L, respectively. Heavy metals in runoff showed relatively high values, possibly due to the abrasion of brake pad or tire while cars are slowly moving for parking. EMCs of total Pb, total Cu, and total Ni are in the range of $1206-16293{\mu}g/L$, $237-7906{\mu}g/L$, and $53-6372{\mu}g/L$, respectively. Pollutant loading per rest area calculated by using EMC, flowrate and target area is also described for each pollutant.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.584-591
• /
• 2017

Metal removal from water has not been explained clearly by either adsorption onto the surface of absorbents or precipitation as metal hydroxides because those occur simultaneously to a certain extent. For a better understanding of the metal removal mechanisms, batch experiments were performed using soil calcined at $850^{\circ}C$ under various pH conditions for Cu, Pb, Zn, Cd, and Cr. The results showed that the metal removal efficiency with the exception of Cr decreased abruptly, even within 5 min, showing more than 90% removal. The pH of each reactant increased gradually from around 7 to 9 with time. The increases in metal removal at higher pH appear to be associated with metal hydroxides precipitation. Comparative experiments, which were carried out changing the pH by reacting with commercial activated carbon (CAC), natural yellow soil (NYS), and calcined yellow soil (CYS), showed that the pH of the CYS only increased with time. Calcination processes might lead to a change in the physical properties of the soil matrix resulting in a high pH when reacted with water. Apart from adsorption onto the surface of the absorbents, these results show that the adsorption and/or precipitation of hydroxides onto the surface of adsorbents also play important roles in regulating the dissolved metals under alkaline conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.5
• /
• pp.118-127
• /
• 2021

Recently, the public's interest in the air environment has increased, and public health is threatened by fine particulate matter. Furthermore, the government continues efforts to improve air quality by expanding the monitoring of air pollutants and reinforcing environmental standards. Since air quality differs depending on the region in the Korean Peninsula, it is currently necessary to identify the cause and search for influencing factors. In this study, the atmospheric environment and regional differences in cities located in the Chungnam Province were observed. As a research method, regression analysis was performed for weather conditions, such as temperature, wind speed, precipitation, and season and targeted at air pollutants, such as SO₂, NO₂, CO, O₃, PM₁₀, and PM_2.5, as well as heavy metals contained in particulate matter, such as Pb, Cd, Cr, Cu, Ni, As, Mn, Fe, Al, Ca, and Mg. In the case of PM₁₀, the concentrations of Mn(0.4884) in Cheonan, CO(0.3329) in Dangjin, and Mg(0.5691) in Seosan were highest. In the case of PM_2.5, Cheonan NO₂(0.4759), Dangjin CO(0.4128), and Seosan NO₂(0.3715) were significantly affected. In summary, the influencing factors vary according to the region in Chungnam province in terms of air quality, and there is a difference in the degree of contribution. Therefore, it is considered that the Korean government's management of air quality is required for each region.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3C
• /
• pp.159-165
• /
• 2010

The problems such as natural resource exhaustion, pollutant emission and waste generation are increasing worldwide with the industrial development. The quantity of the industrial by-product in Korea is 6 million tons a year, and even its basic treatment processes including landfill, incineration and storage have reached their limits. In this study, fly ash and silica fume were applied to shotcrete to develop a method for the reuse of resources and to increase the use of fly ash, which is an industrial waste. An environmental hazard evaluation is a must to actively address the worldwide environmental problems, though. Therefore, an environmental impact assessment was conducted using the chemical content analysis test and heavy metal exudation test, for ten mixtures that were obtained through the pre-mixing and compressive strength tests. The results of the compressive strength test showed that all mixtures satisfied national and international standards. Cr, Cd and Hg were not detected, and Pb was detected only in some cases with fly ash. Cu and As were detected in all mixtures, but all of them satisfied national and international standards.

• Economic and Environmental Geology
• /
• v.56 no.6
• /
• pp.745-764
• /
• 2023

In the Republic of Congo, Banded iron formations (BIFs) occur in two areas: the Chaillu Massif and the Ivindo Basement Complex, which are segments of the Archean Congo craton outcropping in the northwestern and southwestern parts of the country. They show interesting potential with significant mineral resources reaching 2 Bt and grades up to 60% Fe. BIFs consist mostly of oxide-rich facies (hematite/magnetite), but carbonate-rich facies are also highlighted. They are found across the country within the similar geological sequences composed of amphibolites, gneisses and greenschists. The Post-Archean Australian Shale (PAAS)-normalized patterns of BIFs show enrichment in elements such as SiO₂, Fe₂O₃, CaO, P₂O₅, Cr, Cu, Zn, Nb, Hf, U and depletion in TiO₂, Al₂O₃, MgO, Na₂O, K₂O, Sc, Th, Ba, Zr, Rb, Ni, V. REE diagrams show slight light REEs (rare earth elements; LREEs) compared to heavy REEs (HREEs), and positive La and Eu anomalies. The lithological associations, as well as the very high (Eu/Eu^*)_SN ratios> 1.8 shown by the BIFs, suggest that they are related to Algoma-type BIFs. The positive correlations between Zr and TiO₂, Al₂O₃, Hf suggest that the contamination comes mainly from felsic rocks, while the absence of correlations between MgO and Cr, Ni argues for negligeable contributions from mafic sources. Pr/Pr^* vs. Ce/Ce^* diagram indicates that the Congolese BIFs were formed in basins with redox heterogeneity, which varies from suboxic to anoxic and from oxic to anoxic conditions. They were formed through hydrothermal vents in the seawater, with relatively low proportions of detrital inputs derived from igneous sources through continental weathering. Some Congolese BIFs show high contents in Cr, Ni and Cu, which suggest that iron (Fe) and silicon (Si) have been leached through hydrothermal processes associated with submarine volcanism. We discussed their tectonic setting and depositional environment and proposed that they were deposited in extensional back-arc basins, which also recorded hydrothermal vent fluids.

• Asian Journal of Atmospheric Environment
• /
• v.8 no.3
• /
• pp.126-139
• /
• 2014

In order to estimate the influence of sources on $PM_{2.5}$ in the industrial area of Japan, we carried out a source analysis using chemical component data of $PM_{2.5}$. $PM_{2.5}$ samples were collected intermittently at an industrial area in Japan from July 2010 to November 2012. Water soluble ions ($Cl^-$, $NO_3{^-}$, $SO{_4}^{2-}$, $Na^+$,$NH_4{^+}$, $K^+$, $Mg^{2+}$, $Ca^{2+}$), elements (Al, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Cd, Sb, Pb), and carbonaceous species (OC, EC) of the $PM_{2.5}$ (a total of 198 samples) were analyzed. Positive Matrix Factorization (PMF) model was applied to the data of those chemical components to identify the source of $PM_{2.5}$. At this observation site, nine factors were extracted. The major contributors of $PM_{2.5}$ were secondary sulfate 1, in which loading factors of $SO{_4}^{2-}$ and $NH_4{^+}$ were large (percentage source contribution: 20.9%), traffic, in which loading factors of OC (organic carbon) and EC (elemental carbon) were large (20.8%), secondary sulfate 2, in which loading factors of K and $SO{_4}^{2-}$ were large (8.0%), steel mills (7.8%), secondary chloride and nitrate (7.0%), soil (5.0%), heavy oil combustion (3.8%), sea salt (3.8%), and coal combustion (2.3%). The conditional probability function (CPF) and the potential source contribution function (PSCF) were carried out to examine the influence of a regional source and a broad-based source, respectively. CPF results supported local source influences such as steel mills, sea salt, traffic, coal combustion, and heavy oil combustion. PSCF results suggested that ships in the East China Sea, an industrial area of the east coastal region of China, and an active volcano in the Kyushu region of Japan were potential regional sources of secondary sulfate 1. Secondary sulfate 2 was affected by the burning of biomass fields and by coal combustion in Chinese urban areas such as Beijing, Hebei, and western Inner Mongolia. Source characterization using continuous data from one site showed a potential source representing fossil fuel combustion is affected both by regional and broad-based sources.

• Journal of environmental and Sanitary engineering
• /
• v.10 no.1
• /
• pp.25-34
• /
• 1995

A Study on environmental Investigation in Imha Dam for the finding the degree of water quality and heavy metals was carried out at 4 sampling station during the period from August 15, 1993 to May 7, 1994. The results were as follows. 1. The ranges of values of pH for water were st. 1-7.56, st.2-7.77, st.3-7.9, st.4-7,7 on the average. Total average of pH values were 7.56-7.9 2. The ranges of values of DO for water were st.1-8.71($mg/{\ell}$), st.2-8.64($mg/{\ell}$), st.3-10. 25($mg/{\ell}$), st.4-9.01($mg/{\ell}$) on the average. Total average of DO of values were 8.64-10.25($mg/{\ell}$). 3. The ranges of values of BOD for water were st.1-1.1($mg/{\ell}$), st.2-1.0($mg/{\ell}$), st.3-0 86($mg/{\ell}$), st.4-0.99($mg/{\ell}$) on the average. Total average of BOD of values were 0.86-1.1($mg/{\ell}$). 4. The ranges of values of COD for water were st.1-1.12($mg/{\ell}$), st.2-1.4($mg/{\ell}$), st.3-0 98($mg/{\ell}$), st.4-1.46($mg/{\ell}$) on the average. Total average of COD of values were 0.98-1.46($mg/{\ell}$). 5, The ranges of values of T- N for water were st.1-0.36($mg/{\ell}$), st.2-0.49($mg/{\ell}$), st.3-0 23($mg/{\ell}$), st.4-0.83($mg/{\ell}$) on the average. Total average of T-N of values were 0.23-0.83($mg/{\ell}$). 6. The ranges of values of T-P for water were st.1-0.053($mg/{\ell}$), st.2-0.06($mg/{\ell}$), st.3-0.02($mg/{\ell}$), st.4-0.07($mg/{\ell}$) on the average. Total average of T-P of values were 0.02-0.07($mg/{\ell}$). 7. In the E. soli group distribution were counted st.1-1130, st.2-1113, st.3-152.3, st.4-1253 by the MPN test. Total distribution of E. soil group were 152.3-1253. 8. The concentration of heavy metals of Cu, Mn, Pb, Zn were measured st.1-0.59, 0.18, 0 04, 74.6( ${\mu}g/{\ell}$), st.2-0.39,0.29,0.03, 54.3(${\mu}g/{\ell}$), st.3-0.1,0.3, ND, 8(${\mu}g/{\ell}$), st.4-0.96, 0 26,0.23,45.6(${\mu}g/{\ell}$) on the average. Cd, Hg, Cr were not detected in the sampling site.