• Journal of ILASS-Korea
• /
• v.24 no.4
• /
• pp.163-170
• /
• 2019

In this study, feedback logic using dual O₂ sensor values were developed to increase the purification capability of a three-way catalyst (TWC) in a compressed natural gas (CNG) engine. A heavy-duty inline 6-cylinder engine was used and the CNG was supplied to the engine through a mixer. This study consists of two main parts, namely, the proportional integral (PI) control with a front O₂ sensor and the feedback control with dual O₂ sensors. In the PI control experiment, effects of various parameters, such as P gain, I gain, and lean delay, on the TWC capability were identified. Based on the results of the PI control experiment, the feedback logic using dual O₂ sensor values were developed. In both cases, the nitrogen oxides (NO_X) emissions were nearly zero. However, the carbon monoxide (CO) emissions were reduced significant in the feedback logic with dual O₂ sensors than in the PI control with the front O₂ sensor.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.2
• /
• pp.225-236
• /
• 2004

Diesel engines which emit a lot of PM and NOx have been known as a main air polluter. Especially, diesel particulate matters (OPM) including black smoke are hazardous air pollutants to human health and environment. The nations retaining advanced engine technologies have reinforced emission regulations. To meet these regulations diesel engine manufacturers have developed low-emission diesel engines, aftertreatment equipments, alternative fuel technologies and so on. In this study, particle number concentrations characteristics according to particle size and engine driving conditions were analyzed when these low-emission technologies were applied. There was a tendency of increasing particle number concentrations from heavy-duty diesel engines with increasing engine rpm and load rate. In the cases of COPF (Catalytic Diesel Particulate Filter), CNG (Compressed Natural Gas) engine and ULSD (Ultra Low Sulfur Diesel) more than 99% of particle number concentration were removed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.128-139
• /
• 2000

Environmental concerns and shortage of petroleum have promoted considerable interest in the use of alternate fuels in stationary diesel engine. In this study, a heavy-duty, intercooler-turbocharged 6-cylinder stationary diesel engine was converted into stationary gas engine fueled with propane or natural gas for the cogeneration plants. One of the most important factors in the combustion features of a stationary gas engine is the fuel composition and operating parameters in terms of compression ratio, spark advance, and engine loads. Experiments with different fuel gas and load conditions were carried out with combustion pressure analysis and NOx measurement. Combustion analysis based on P-$\theta$ diagrams was also investigated by means of combustion duration and cycle variation. Compression ratio is 10.0 and ignition timing is set by using the gasoline setting as a base line and advanced toward BTDC. The results show that fuel composition and spark advance have dominant effects on combustion and NOx characteristics at operating conditions.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.5
• /
• pp.80-87
• /
• 2003

Air partial pressure ratio and inlet air mass flow are influenced by water vapor and gaseous fuel in mixture on Compressed Natural Gas (CNG) engines. In this paper, the effects of the water vapor and the gaseous fuel that change the air mass flow and the air-fuel ratio are studied. Effective air mass ratio is defined as the air mass flow divided by mixture mass flow, and also it is applied to the estimation of the inlet air mass flow and the air-fuel ratio. The presence of the gaseous fuel and the water vapor in the mixture reduces the air partial pressure and the effective air mass ratio of the CNG engines. The experimental results for the CNG engine show that estimation of the air-fuel ratio based upon the effective air mass ratio is more accurate than that of a normal mode.

• Journal of the Korean Institute of Gas
• /
• v.25 no.6
• /
• pp.66-73
• /
• 2021

In this study, The full load test and WHTC mode test were performed to examine the effect on a heavy duty natural gas engine according to the type of standard gas for certification to check engine performance and exhaust characteristics. Two types of standard gas (G_r, G₂₃) and commercially available natural gas were applied as the fuel used. As a result of the test results of three natural gases with different fuel compositions, G₂₃ with a high nitrogen content was inferior in torque, fuel consumption, and thermal efficiency conditions. In addition, when evaluated in the WHTC mode it was possible to obtain a result that satisfies the EURO VI regulation. However, compared to the other two fuels, the emission characteristics of G₂₃ decreased CO2 and CO, but increased CH4, NOx and PN emissions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.146-153
• /
• 2013

CNG buses has contributed to improve air quality in cities. But it is difficult to meet the next emission regulations such as EURO-VI without the help of additional post-processing device. Hydorgen has higher flame speed and lower combustion temperature that make it thermal efficiency increase with leaner operation. Using hydrogen natural gas blend (HCNG) fuel is promising technology which can reduce $NO_x$ and $CO_2$ emissions for a natural gas vehicle. However, fuel flow rate of HCNG should be increased since hydrogen's energy density per volume is much smaller than natural gas. In the present study, the characteristics of fuel supply system and its applicability were evaluated in a heavy duty natural gas engine. The results showed that the potential of fuel pressure regulator and fuel metering valve had enough capacity with HCNG. Employed mixer did not affect the distribution characteristics of mixture.

• Journal of Energy Engineering
• /
• v.25 no.1
• /
• pp.122-130
• /
• 2016

This study is a numerical study using commercial simulation program GT-Power on 1.5MW diesel engine for power generation. Performance comparison has done for diesel operation with dual fuel operation for different engine load(50%, 75%, 100%) using the target engine model with additional gas injection system. Effect of using Hi-sene, which is actually being used in island area, instead of diesel was also studied. As a result, under 60% natural gas with diesel condition, BSFC was increased by 32% without modifying system. There was almost no change for natural gas/Hi-sene condition compared with natural gas/diesel condition. Decrease of burned fuel fraction was the main reason of these phenomena. After optimizing system, BSFC was improved by 2%.

• Journal of the Korean Institute of Gas
• /
• v.21 no.5
• /
• pp.9-15
• /
• 2017

Natural gas fuel has known to be very promising in terms of abundancy and economic value. Therefore it is widely treated as research topics in a variety field of production, storage and utilization. Natural gas has become one of the major sources for the power generation by using internal combustion engines(ICE). Development of natural gas fuel injection device should be preceded to realize a reliable natural gas fuel supply system for a MW class power generation reciprocating ICE. In this research, an injection valve which consists of solenoid and body part with a moving plate was designed and its dynamic performance was experimented in the engine-like environment. Displacement length and diameter of an armature and diameter of a solenoid coil were tested at former study. In this research the effect of materials of solenoid core, size of main housing inlet and supply gas pressure are examined.

• Journal of the Korean Institute of Gas
• /
• v.19 no.6
• /
• pp.8-14
• /
• 2015

Synthetic natural gas(SNG), acquired from coal, is regarded as an alternative to natural gas since a rise in natural gas due to high oil price can be coped with it. In the present study, 11-liter heavy duty compressed natural gas(CNG) engine was employed in order to examine the combustion and emission characteristics of SNG. The simulated SNG, made up 90.95% of methane, 6.05% propane and 3% hydrogen was used in the experiment. Power output, thermal efficiency, combustion stability and emission characteristics were compared to those with CNG at the same engine operating conditions. Knocking phenomenon was also analyzed at 1260 rpm, full load condition. Combustion with SNG was more stable than CNG. Nitrogen oxides emissions increased while Carbon dioxides emissions decreased. Anti-knocking characteristics were improved with SNG.

• Journal of Korean Society for Atmospheric Environment
• /
• v.13 no.3
• /
• pp.215-220
• /
• 1997

CNG dual fuel engine for heavy duty diesel engine developed by AFS International in Canada has been equipped to a Korean city bus engine and tested to compare the engine performance and the emission characteristics with the existing diesel fueled engine. Also the dual-fuel engine was applied to the city bus for road test. The results are summarized as follows. Performance optimization has been carried out to have engine power equivalent to or better than the diesel fueled engine. Smoke is decreased by 85% by Korean smoke 3 mode test. By 13 mode test CO is increased by 453% and THC is increased by 2, 086%. NOx is decreased by 7% in laboratory. D-13 test mode was changed in 1996 Korean regulation. Even though THC is increased very much, it's not too serious problem since CO and HC emission of diesel engine is very little compared to gasoline engine and more than 75% of THC is CH$_4$. But the reduction technologies of CO and HC has to be considered.