• KIEAE Journal
• /
• v.1 no.1
• /
• pp.17-26
• /
• 2001

The purpose of this study is to develop an underground Building. Population tends to concentrate in large cities. In result, the cities lacks housings. Underground space may be a attractive space by being able to gain alternative energy and get a cheap site, protect environment at the same time. The earth or ground is a useful medium for a long-term heat source and storage of it's heat. Also the underground space has the status of stabilization, the lower heating load and the similar heat transfer coefficient of the inside wall surface comparing to that of residential space. Utilization of underground space has many advantages to cope with lack of building sites and energy conservation, etc. As a result, it is expected to provide a useful information for the practical use of Underground building.

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2310-2312
• /
• 2004

In Korea Electric Power Corporation (or KEPCO), several Demand-Side Management (or DSM) program have been carried out to effectively meet electric power demand at least costs by modifying customers electricity use patterns. As one of them, KEPCO applies low-priced night thermal-storage power service for heat appliances to facilitate efficient use of power facilities by shifting relatively high daytime demands to night hours to build loads during the off-peak periods. In the market of heat-storage type water-heater, electric water-heater has been mostly used, but it has low energy efficiency and needs high capacity electric equipments. So in order to replace these electric water heaters, 15 HP air-source heat pump water heater is developed in Korea Electric Research Institute (or KEPRI). This paper shows that measurement system for performance testing of heat pump water heater is established and heating capacity and performance is analyzed and measured for out-door environmental change.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.2
• /
• pp.305-311
• /
• 2003

This Paper Presents an information about the heat transfer characteristics of a separate type thermosyphon in electronic equipments. The heat removal problem of electronic equipments is regarded as an important factor and a separate type heatpipes can be utilized as a cooling device of electronic equipments (such as CPU of a Personal computer or notebook). In this study. heat source ($50\times50\times2 mm $aluminum Pseudo CPU) was used for the experiment. The device can transfer heat from the evaporator to the condenser through natural circulation (without any external driving forces) and the results indicate that the device is capable of dissipating over 60W of thermal energy and keeping the heating plate surface temperature under $50^{\circ}C$.

• Journal of computational fluids engineering
• /
• v.5 no.2
• /
• pp.47-54
• /
• 2000

A robust Navier-Stokes code has been developed to efficiently predict hypersonic flows in chemical nonequilibrium. The HLLE+ flux discretization scheme is used to improve accuracy and robustness of hypersonic flow analysis. An efficient LU approximate factorization method is also used to solve the flow equations and species continuity equations in fully coupled fashion to implicitly treat stiff source terms of chemical reactions. The HLLE+ scheme shows lower grid dependency for the wall heating rates than other schemes. The developed code has been used to compute chemical nonequilibrium air flow through expanding hypersonic nozzle and past two and three dimensional blunt-nosed bodies. The results are in good agreement with existing numerical and experimental results.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.77-82
• /
• 2009

If we can supply accurate minute flow rate to the households, we can solve many problems that are occurring in consequences of uncontrolled flow rate for the households. Therefore, this paper presents an innovative solution to the source of the problems by illustrating how we can control the flow rate to the household. This paper proves such problems even can be solved in a case when there is a room turned off the heating.

• Journal of the Korean Ceramic Society
• /
• v.27 no.4
• /
• pp.553-559
• /
• 1990

The nonuniform shrinkage has been investigaed in pressureless sintering of $\alpha$-SiC, where born carbide and phenolic resin as a carbon source are used as densification aids. Compacted specimens, prepared from the granulated powder, were sintered at 215$0^{\circ}C$ for 30min in Ar atmosphere. Using the fresh and unseasoned graphite crucible, the upwarped specimens were obtained, while specimens were uniformly shrunk in the seasoned crucible. This effect is mainly due to the nonuniform distributjion of boron carbide during heatig, which originates in the reaction of boron carbide with CO gas, providing from the result of SiO2 reduction with carbon during heating.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2000.11a
• /
• pp.169-172
• /
• 2000

This paper describes a Push-Pull type high frequency resonant inverter composed of consolidation of boost converter circuit and resonant inverter circuit. By using a boost converter circuit, the proposed inverter can obtain a twice input voltage of resonant circuit and reduce a secondary turn ratios. also, by using both switching device of boost-converter and resonant circuit, the number of switching device can be reduced by half, the analysis of the proposed circuit was generally described by using normalized parameter and operating characteristics have been evaluated as to switching frequency and parameters. In the future, this proposed inverter shows that is can be practically used as a power source system for the lighting equipment of discharge lamp, induction heating applications.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.04a
• /
• pp.100-103
• /
• 2005

This work discusses the numerical analysis, the design and experimental test of the SMA (Shape Memory Alloy) actuator along with its capabilities and limitations. Convection heating and cooling using water actuate the SMA element of the actuator. The fuel such as propane, having a high energy density, is used as the energy source for the SMA actuator in order to increase power and energy density of the system, and thus in order to obviate the need for electrical power supplies such as batteries. The system is composed of a pump, valves, bellows, a heater (burner), control unit and a displacement amplification device. The actuation frequency is compared with the prediction obtained from numerical analysis. For the designed SMA actuator system, the results of numerical analysis were utilized in determining design parameters and operating conditions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.7 s.238
• /
• pp.970-975
• /
• 2005

This paper presents a novel microgenerator of $CO_2$ (carbon dioxide) gas. $NaHCO_3$ (sodium bicarbonate) in a chamber is decomposed by the underlaid microheater. Alternatively, water droplet is caged by paraffin layer and released by heating. The released water dissolve HOC(COOH)$(CH_2COOH)_2$ (citric acid) powder and then, $NaHCO_3$ reacts with the solubilized HOC(COOH)$(CH_2COOH)_2$ and $CO_2$ is produced. Micropumps actuated by $CO_2$ generation were fabricated. A portable micro cell incubator of which pH is controlled by the produced $CO_2$ is also presented as one of the further applications.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.42-44
• /
• 2007

Methods of repair welding are different to production welding for welding position, welding process, welding power source, heating methods. This study investigated proper the welding process used the welding process SMAW and GTAW in the weldment of inconel filler metals. Mechanical test showed that SMAW and GTAW process had higher mechanical properties than those of material specification. Both SMAW and GTAW welding process can appy the repair welding. In comparison, GTAW welding process had more higher mechanical properties in the weldment.