• The Journal of the Petrological Society of Korea
• /
• v.15 no.1 s.43
• /
• pp.10-24
• /
• 2006

Staurolite grains in staurolite, kyanite and sillimanite zones occurred in the Littleton Formation, Northcentral Massachusetts have interpreted to form by Barrovian-type metamorphism during Acadian orogeny. However, various occurrence of staurolite in the three zones, (a) porphyroblast, (b) randomly oriented and coarse-grained muscovite pseudomorph after staurolite, (c) recrystallized staurolite at the margin of garnet porphyroblast and within the pseudomorph, indicates that they have resulted from polymetamorphism. Staurolite in these three metamorphic zones can be formed by demise of chlorite or chloritoid that depends on difference of bulk-rock compositions and changes of P-T conditions. Staurolite modal proportion calculated in MnNCKFHASH system using THERMOCALC program reveals that staurolite could have grown with garnet with increasing pressure and temperature, if it coexist with chlorite. After demise of chlorite and appearance of biotite, staurolite mode decrease with increasing pressure and temperature. Therefore, based on the previous P-T paths for the Acadian metamorhism, staurolite porphyroblast grew with garnet during 400-370 Ma. Randomly oriented and coarse-grained muscovite pseudomorphs after staurolite probably have grown due to heating with appearance of kyanite and sillimanite. Consequently, pseudomorphisrn of staurolite occurred by heating derived from locally intense Alleghanian shearing (ca. 320-300 Ma) overprinted the Acadian metamorphism. Recrystallized fine-grained staurolite in sillimanite zone observed between the grain boundaries of muscovite in the pseudomorphs and at the edge of garnet porphyrobasts has formed during decreasing temperature and pressure (ca. 300-280 Ma) after peak temperature (ca. $700^{\circ}C$) of the Allegllanian metamorphism.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.69-75
• /
• 2019

The cooling performance of heat pump system for light-duty commercial electric vehicle was evaluated experimentally. The cooling performance characteristics of the heat pump for light-duty commercial electric vehicles were evaluated by varying the temperature, flow rate of chiller coolant, and electric compressor speed, under the exterior air temperature of 35 ℃ and interior air temperature of 25 ℃. Increasing the compressor speeds decreased the cooling system efficiency by 16.4 % on average with the cooling capacity increasing by 8.0 % on average and the compressor work increasing by 27% on average. To use waste heat from the coolant to chill power electronic components, such as the motor and inverter, a chiller was installed to transfer heat between the coolant and refrigerant. Increasing the temperature of the chiller coolant from 35 ℃ to 55 ℃ decreased the efficiency by 18.2 % on average due to higher condensing heat source. Increasing the coolant flow rate from 10 liter/min to 20 liter/min did not affect the cooling capacity of the system due to a similar total condensing heat transfer rate at the chiller and the exterior heat exchanger. In future works, heating performance will be investigated by varying the operating conditions to use the chiller's waste heat with an improvement of heating capacity.

• Journal of Energy Engineering
• /
• v.21 no.2
• /
• pp.168-178
• /
• 2012

The objective of this study is applied to office buildings to evaluate quantitative evaluation method about performance of double-skin at design stage to establish the basis for the purpose of evaluation performance. Select the evaluation building about design plan for applying the double-skin using the dynamic heat load analysis program the annual heating and cooling load of before and after the double-skin. Using CFD to analyze wind factor and applied ventilation for realistic results. Effects of double-skin to apply, and control techniques that can be done more realistically proposed through to set and control for shade control mode of ventilator and inside cavity wall of double-skin. Apply for the building the double-skin due to interpretation of the annual heating and cooling loads applied to interpret the quantitative effect confirmed the possibility. According to the form of a double skin was confirmed cavity environmental changes.

• Analytical Science and Technology
• /
• v.29 no.5
• /
• pp.242-247
• /
• 2016

This research aims to set up and validate methods of analyzing the methanol in wet wipes and verifies the analysis methods that applied to the wet wipes. We used Headspace (HS) Gas Chromatography (GC) - Flame Ionization Detector (FID) to the establish analysis method of methanol in wet wipes and optimized heating temperature, heating time, GC conditions with column. The result indicated that 3 mL of sample in 20 mL headspace vial can be equilibrated efficiently in headspace sampler at 70 ℃ for 10 min and sample was measured by GC with spli injection mode(10:1). The results show that linearity from 1 to 100 ppm was over R2 0.9995, precision was RSD 1.83 % and accuracy(recovery rate) was 105.44 (±1.05 %) on water matrix and wet wipes matrix removed non-woven fabric. Also, monitoring results of total 20 cosmetics on the market, from 0.00017 to 0.00156 % of methanol was detected from wet wipes.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.4
• /
• pp.176-181
• /
• 2003

Rapid densification of a SiC powder with additive 0.5 wt% $B_4$C was conducted by spark plasma sintering (SPS). The unique features of the process are the possibilities of using very fast heating rate and short holding time to obtain fully dense materials. The heating rate and applied pressure were kept to be $100^{\circ}C$/min and 40 MPa, while sintering temperature and soaking time varied to 1800, 1850, 1900 and $1950^{\circ}C$ and 10, 20 and 30 min, respectively. All of the SPS-sintered specimens at $1950^{\circ}C$ reached near-theoretical density. The XRD found that 3C-to-6H transformation at $1850^{\circ}C$. The microstructures of the rapidly densified SiC ceramics consisted of duplex microstructure with ultrafine equiaxed grains under 2 $\mu\textrm{m}$ and elongated grains of 0.5∼2 $\mu\textrm{m}$ wide, length 3∼10 $\mu\textrm{m}$. The biaxial strength increased with the increase of sintering time. Strength of 392.7 MPa was obtained with the fully densified specimen sintered at $1950^{\circ}C$ for 30 min, in agreement with the general tendency that strength increases with decreases pore. On the other hand, the fracture toughness shows the value of 2.17∼2.34 MPa$.$$m^{1/2}$ which might be due to the transgranular fracture mode.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.134-134
• /
• 2015

최근 액체 플라즈마에 대한 주된 이슈는 방전에 의해 발생하는 히드록실라디칼(OH-)과 버블이다. 액체 플라즈마를 이용한 다양한 응용분야에서는 히드록실라디칼에 주목하고 있다. 액체 플라즈마는 그래핀 파생물의 용액 친화도 향상을 위해 이용될 수 있다. 흑연이 포함된 과산화수소(H2O2) 용액에서 전기적인 방전으로 만들어진 히드록실라디칼로 그래핀 파생물의 용액 친화도를 향상시킨다. 이는 잠재적인 프린팅(printing) 기술 발전에 기대된다. 그리고 이 라디칼은 폐수에서 발암성의 트라이클로로아세트산(CCl3COOH)을 탈 염소하고 분해하는 역할을 하여 액체 플라즈마가 새로운 수처리 기술로 부상되고 있다. 또한 인체에서는 살균 작용을 하는 것 뿐만 아니라 단백질 고리를 끊는 역할을 하여 전립선 수술과 같은 인체수술에 적용될 수 있다. 최근 액체 플라즈마를 이용한 돼지 각막 임상수술에서 레이저와 필적할 정도로 매우 정밀하게 수술된 연구결과가 발표되어 인체 각막수술 적용에 기대된다. 이처럼 액체 플라즈마를 이용한 대부분의 응용분야에서 히드록실라디칼의 역할이 중요하다. 액체 플라즈마의 또 다른 이슈인 버블은 2가지의 역할을 한다. 첫 번째로 방전소스의 역할이다. 액체 속에 담긴 얇은 전극에 전압을 인가하면 전극 주변에서 강한 전기장의 발생으로 줄열(joule heating)에 의해 버블이 생성된다. 전극에서 버블이 생성되었을 때, 서로 다른 유전율을 가진 두 물질로 나누어진다. (버블 안은 공기로 상대 유전율 ${\varepsilon}r{\fallingdotseq}=1$, 용액은 ${\varepsilon}r{\fallingdotseq}=80$이다.) 시스템에 인가된 전압이 항복 전압(breakdown voltage)을 넘어서면 유전율이 상대적으로 낮은 버블내부에 강한 전기장이 걸리게 되어 방전이 일어난다. 만약 버블이 존재하지 않는다면 방전을 위해서 매우 높은 전압이 필요하다. 따라서 버블은 플라즈마 방전의 소스역할을 한다. 두번째로 버블은 전극의 부식을 방지하는 역할을 한다. 전극 부식은 주로 전기분해로 인한 산화반응에 의해 발생하는데 버블을 전극에 오래 머무르게 하면 부식을 방지할 수 있다. 이처럼 액체 플라즈마 시스템에서 버블의 역할들은 상당히 중요하다. 일반적으로 버블은 시스템에 인가하는 전원, 전극 극성 그리고 전압크기에 따라 거동이 달라진다. 시스템에 AC파워를 인가하면 버블은 주파수가 높을수록 전극에서 떨어지는 속도가 빨라지는 특성을 보인다. 핀 전극 극성이 음극일 때는 양극일 때보다 버블이 더 잘 생성된다. 또한 인가전압크기에 따라 거동이 달라지며 시스템에 같은 전압을 인가하여도 크기가 항상 같지 않고, 거동도 일관성을 보이지 않은 랜덤적인 모습을 보인다. 본 연구에서는 이 랜덤적인 버블의 거동을 정리하고 응용분야에서 중요하게 여기는 히드록실라디칼 생성에 대해 공부하기 위해 염류 용액(saline solution)에 핀(pin)-면(plane) 전극 구조를 설치하여 10Hz 주파수(1% duty cycle)를 가진 0-600V 구형펄스로 실험하였다. 실험을 통한 결과로서 랜덤적인 버블의 거동을 전극에서 버블이 떨어지는 속도와 플라즈마 특성에 따라 슈팅모드(shooting mode)와 유지모드(keeping mode) 2가지 모드로 분류하였다. 슈팅모드에서는 버블이 핀 전극에서 성장하지 못하고 빠른 속도로 떨어지는 모드로 플라즈마 방전이 잘 이루어지지 않는다. 반면 유지모드에서는 버블이 핀 전극에서 떨어지지 않고 지속적으로 성장한다. 이 모드에서는 펄스 시간 동안 하나의 버블로 연속적인 방전이 가능하다. 방전이 일어날 때 발생하는 히드록실라디칼의 생성은 버블 내부의 쉬스와 관련이 있다. 이 라디칼을 만들기 위해서는 높은 에너지가 요구되기 때문에 버블 내부의 쉬스(sheath)에서 만들어진다. 펄스 동안 쉬스는 주로 핀 전극 주변에서 유지되며 히드록실라디칼은 이곳에서 주로 만들어진다. 따라서 버블과 함께 쉬스도 성장하는 버블유지모드에서 슈팅모드보다 히드록실라디칼이 더 많이 생성된다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.22-28
• /
• 2017

The performance of lithium ion batteries used in electric vehicles (EV) varies greatly depending on the battery temperature. In this paper, the finite difference method was used to evaluate the temperature change, state of charge (SOC), internal resistance, and voltage change of the battery due to heat generation in the battery. The simulation model was linked with AMESim to calculate the driving range of an EV traveling in New European Driving Cycle (NEDC) mode. As the temperature dropped below $25^{\circ}C$, the internal resistance of the battery increased, which increased the amount of heat generated and decreased the driving range of EV. At battery temperatures above $25^{\circ}C$, the driving range was also decreased due to reduced SOC that deteriorated the battery performance. The battery showed optimal performance and the driving range was maximized at $25^{\circ}C$. When battery temperatures of $-20^{\circ}C$ and $45^{\circ}C$, the driving range of EV decreased by 33% and 1.8%, respectively. Maintaining the optimum battery temperature requires heating the battery at low temperature and cooling it down at high temperature through efficient battery thermal management. Approximately 500 W of heat should be supplied to the battery when the ambient temperature is $-20^{\circ}C$, while 250 W of heat should be removed for the battery to be maintained at $25^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.139.2-139.2
• /
• 2015

In this study, We applied the magnetic field that has CW frequency and AM frequency to heating magnetic nano powder. For this experiment, We set up the devices flat-type magnetic field generator with CW frequency and AM frequency. We supplied the current to encircling coil by adjusting the power of generating of magnetic field device for AC voltage through Slidacs and using way of LC resonance circuit and SMPS(Switching Mode Power Supply). Above the encircling coil, We covered the circular flat insulator like glass. And we located the well plate containing the magnetic nano powder liquor above the circular flat insulator and exposed the magnetic field to this well plate. Using the flat-type magnetic field generator with CW and AM frequency and the magnetic field measurement sensor(Magnetic pick up coil or Hall sensor), We measured the strength of the magnetic field of circular flat insulator's surface in each position. The temperature of the magnetic nano powder in the well plate was quantitatively measured by the magnetic field strength through the Fluoroptic thermometer.

• Journal of Sensor Science and Technology
• /
• v.11 no.5
• /
• pp.279-285
• /
• 2002

Two $SnO_2$ based sensing films(pure $SnO_2$ and $SnO_2$/Pt) and a Pt thin film for temperature sensor on an alumina substrate were designed and fabricated for classifying the indoor environmental gases. By controlling the heating power in the shape of trapezoid, unique four sensing response curves created from both $SnO_2$ film and $SnO_2$/Pt film. Then, various parameters were extracted from sensing response curves and carried out principal component analysis(PCA). The results confirm that a sensor array with the proposed operating mode was extremely effective in classifying indoor environmental gases such as $CO_2$, $C_3H_8$, $C_4H_{10}$.

• Journal of Power System Engineering
• /
• v.9 no.2
• /
• pp.81-87
• /
• 2005

This study is numerical analysis on the increasing temperature characteristics of vaporizer fin for liquefied natural gas with super low temperature. Existing LNG vaporizers use the direct contact heat transfer mode where the extreme super low temperature LNG of $-162^{\circ}C$ flows inside of the tubes and about $20^{\circ}C$air flows on outside of the fin. Recently, the vaporizers with great enhanced performance compared to conventional type have been developed to fulfill these requirements. The vaporizing characteristic of LNG vaporizer with air as heat source has a fixed iced. These characteristic cause a low efficiency in vaporizer, total plant cost and installing space can be increased. The vaporizing characteristics of LNG via heat exchanger with air are analytically studied for an air heating type vaporizer. This study is intended to supply the design data for the domestic fabrication of the thickness and angle vaporizer fin. Governing conservation equations for mass, momentum and energy are solved by STAR-CD based on an finite volume method and SIMPLE algorithm. Calculation parameter is fin thickness, setup angle and LNG temperature. If the vaporization performance of the early stage and late stage of operating is considered, the case of ${\phi}=90^{\circ}$ was very suitable. In this paper was estimated that the heat transfer was most promoted in case of THF=2mm.