• Journal of Environmental Health Sciences
• /
• v.42 no.2
• /
• pp.118-125
• /
• 2016

Objectives: The traditional type of residence in used in Mongolia, called a ger, is an important residential form and applies coal combustion for cooking and heating. The combustion of coal in ger is the major source of indoor air pollution. The purposes of this study were to measure indoor air pollution in ger and determine the effect of cooking and heating activities. Methods: Indoor temperature, relative humidity, particulate matter less than $2.5{\mu}m$ ($PM_{2.5}$) and black carbon (BC) were continuously measured for 24 hours in eight ger. The measurements were conducted in January or February 2015. Heavy metals in $PM_{2.5}$ filter samples were analyzed by ICP-MS. Results: Average indoor temperature and relative humidity were $19.6{\pm}4.6^{\circ}C$ and $21.4{\pm}5.2%$, respectively. The average indoor $PM_{2.5}$ concentration in the eight ger was $119.8{\mu}g/m^3$ and ranged from 69.4 to $202.7{\mu}g/m^3$. The peak concentrations of $PM_{2.5}$ and BC during cooking and heating periods were several times higher than the 24- hour average concentration. Conclusion: The major contributor to indoor $PM_{2.5}$ and BC concentrations in the ger was coal combustion for cooking and heating.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.1
• /
• pp.43-48
• /
• 2017

In recent years, the demand for ships and offshore platforms that can navigate and operate through the Arctic Ocean has been rapidly increasing due to global warming and large reservoirs of oil and natural gas in the area. Winterization design is one of the key issues to consider in the robust structural safety design and building of ships that operate in the Arctic and Sub-Arctic regions. However, international regulations for winterization design in Arctic condition regulated that only those ships and offshore platforms with a Polar Class designation and/or an alternative standard. In order to cope with the rising demand for operating in the Arctic region, existing and new Arctic vessels with a Polar Class designation are lacking to cover for adequate winterization design with HSE philosophy. Existing ships and offshore platform was not designed based on reliable data based on numerical and experiment studies. There are only designed as a performance and functional purposes. It is very important to obtain of reliable data and provide of design guidance of the anti-icing structures by taking the effects of low temperature into consideration. Therefore, the main objective of this paper reconsiders anti-icing design of aluminum helideck using the heating cable. To evaluate of reliable data and recommend of anti-icing design method, various types of analysis and methods can be applied in general. In the present study, finite element method carried out the thermal analysis with cold chamber testing for performance and capacity of heating cables.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.244-251
• /
• 2003

A two-dimensional BEM code, $FRACOD^{2D}$, was applied to simulate fracture initiation and propagation processes in a rock pillar during an in situ heater test of a rock pillar planned at the $\"{A}sp\"{o}$ Underground Rock laboratory of SKB, in Southern Sweden. To take the advantage of conventional BEM for simulating fracturing processes, but without efforts for domain integral transformation, a hybrid approach is developed to simulate the fracturing processes in rock pillar under coupled thermo-mechanical loading. The code FRACOD was used for simulating the fracture initiation and propagation processes with its boundary tractions reflecting the effects of the initial and redistributed thermomechanical stresses in the domain of interest at multiple excavation and heating steps were produced by a special algorithm of stress inversion, based on resultant thermo-mechanical stress fields at each excavation and heat loading step by a FEM code without considering fracturing processes. This hybrid approach can take the advantages of both types of numerical methods and avoids their shortcomings for fracturing process simulation and domain effects, respectively. In this paper, we present the hybrid approach for the stress, displacements, and fracturing processes at sequential excavation and heating steps of the in situ heater test as a predictive modelling, the formulation of the fracturing models and the predictive results. Two sections of borehole depth, 0.5 m and 1.5 m below the tunnel floor are considered. The pillar area is modelled with the FRACOD and the stress field produced by excavation and heating is transferred with corresponding boundary stresses. From the modelling results, the degree of fracturing and damage are evaluated for 120 days of heating. Dominated shear fracturing in the vicinity of the central pillar was observed from the models at both sections, but spalled area appears to be limited. Based on the modelling results, a sensitivity study for the effect of pre-existing fractures in the vicinity of the holes is also conducted, and the initiation and evolution of EDZ around the deposition holes are investigated using this particular numerical technique.

• Radiation Oncology Journal
• /
• v.2 no.1
• /
• pp.11-20
• /
• 1984

The renewed interest in the use of hyperthermia in cancer therapy is bases on radiobiological and clinical evidence indicated that there may be a significant therapeutic advantage with the use of heat alone or combined with radiation or chemotherapy, There are many methods for generating heat for localized tumor as like radiofrequency, microwave, electromagnetic induction and ultrasound. But it is very difficult to be even thermal dose distribution and stable output of power and then the detection of temperature in tumor is difficult to be precise with thermocouples and semiconductor sensors. We designed the microwave heating generator, dipole antenna applicators and autometic temperature controlled thermocouples for localized hyperthermia on skin and in cavities. 1. The microwave generator with 120 W, 2,450MHz magnetron could be heating up to $40^{\circ}C\~50^{\circ}C\;for\;1\~2$ hours in living tissues. 2. The thermal dose distribution in tissue with microwave was described $42^{\circ}C\~44^{\circ}C$ with in 3 cm depth and $2\~6cm$ diameter area. 3. Skin surface heating applicator with spiral 3 times wave length antenna radiated high Power of microwave. 4, Intracavitary heating applicator with dipole antenna with autometic control temperature sensor kept up continuously constant temperature in tissue. 5. For constant thermal distribution, applied two steps power with 10W microwave after $17\~20W$ during first 10 minutes. 6. The cooling rate by blood flew in living tissue was rised as $10\%$ then meats.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.4
• /
• pp.591-597
• /
• 2009

Egg white protein (EWP) was glycated with maltopentaose (MP) through the Maillard reaction and subsequently phosphorylated by $85^{\circ}C$ dry-heating at pH 4.0 for 1 d in the presence of pyrophosphate. The functional properties of glycated, phosphorylated EWP were compared with those of native EWP and with EWP which was phosphorylated by dry-heating in the presence of pyrophosphate under the same conditions. The phosphorus content of EWP was increased to ~0.60% by phosphorylation, and to ~0.74% by glycation with MP and subsequent phosphorylation. The electrophoretic mobility of EWP increased through phosphorylation. The stability of EWP against heat-induced insolubility at pH 7.0 was considerably improved by phosphorylation alone and further by phosphorylation after glycation. The anti-ovalbumin antibody response was reduced significantly by glycation and phosphorylation, and further reduced by phosphorylation after glycation. The anti-ovomucoid antibody response was reduced significantly by glycation, phosphorylation and phosphorylation after glycation. The calcium phosphate-solubilizing ability of EWP was enhanced by both phosphorylation methods.

• Korean Journal of Food Science and Technology
• /
• v.25 no.5
• /
• pp.461-467
• /
• 1993

The purpose of this study was to investigate the physico-chemical properties of potato starch heated with microwave. Two types of potato starches are prepared; in group A raw potato starch was heated with microwave and in group B potato starch was isolated from potato heated with microwave. Both groups were exposed to the microwave energy in a 560 W, 2,450 MHz oven for 60, 120, 180 and 300 seconds. As the microwave heating time took longer, free lipid decreased and bound lipid increased in both groups. The shape of starch granules, birefrigence and X-ray diffraction pattern were not changed much by microwave heating in both groups. Water binding capacity increased, but amylose content, swelling power and solubility decreased as the microwave heating time took longer. It was also found that the extent of decreases in swelling power and solubility were different between group A and group B.

• Applied Biological Chemistry
• /
• v.40 no.3
• /
• pp.220-224
• /
• 1997

As corn starches with different amylose content were heated at different temperature $(100^{\circ}C,\;121^{\circ}C)$ with starch / water ratio (1:3.5, 1:9) and heating-cooling treatment was repeated up to 4 times, the yield of RS(resistant starch) from heated corn starches was investigated by the enzymatic-gravimetric method and the ${\alpha}-amylase$ treatment. Compared to ${\alpha}-amylase$ method, enzymatic-gravimetric method was more effective to hydrolyze the amorphous region of heated corn starch. With increasing the amylose content and the number of heating-cooling treatment, the yield of RS increased, regardless of isolation method. Heated corn starches formed at $121^{\circ}C$ provided higher yield of RS than those formed at $100^{\circ}C$. Higher RS yield was also observed in the case of starch/water ratio (1:3.5) compared to the case of ratio (1:9).

• Plant Journal
• /
• v.15 no.1
• /
• pp.31-37
• /
• 2019

In this study, to improve the accuracy of forecast of heat demand in the district heating system, this study applied heat demand performance among the main factors of district heating demand forecast in Pankyo area as the heat sales information of the user facility instead of existing heat source facility heat supply information, and compared the existing method with the accuracy based on the actual value. As a result of comparing the difference of the forecasts values of the existing and changed methods based on the performance values over the one week (2018.01.08 ~ 01.14) during the hot water peak, the relative error decreased from 7% to 3% The relative error between the existing and revised forecasts was 9% and 4%, respectively, for the five-month cumulative heat demand from February to February 2018, Also, in case of the weekend where the demand of heat is differentiated, the relative error of the forecasts value is consistently reduced from 10% to 5%.

• Carbon letters
• /
• v.17 no.1
• /
• pp.1-10
• /
• 2016

Lignocellulosic biomass conversion to biofuels such as ethanol and other value-added bio-products including activated carbons has attracted much attention. The development of an efficient, cost-effective, and eco-friendly pretreatment process is a major challenge in lignocellulosic biomass to biofuel conversion. Although several modern pretreatment technologies have been introduced, few promising technologies have been reported. Microwave irradiation or microwave-assisted methods (physical and chemical) for pretreatment (disintegration) of biomass have been gaining popularity over the last few years owing to their high heating efficiency, lower energy requirements, and easy operation. Acid and alkali pretreatments assisted by microwave heating meanwhile have been widely used for different types of lignocellulosic biomass conversion. Additional advantages of microwave-based pretreatments include faster treatment time, selective processing, instantaneous control, and acceleration of the reaction rate. The present review provides insights into the current research and advantages of using microwave-assisted pretreatment technologies for the conversion of lignocellulosic biomass to fermentable sugars in the process of cellulosic ethanol production.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.239.2-239.2
• /
• 2015

Graphene is a most interesting material due to its unique and outstanding properties. However, semi-metallic properties of graphene along with zero bandgap energy structure limit further application to optoelectronic devices. Recently, many researchers have shown that band gap can be induced in the Bernal stacked bilayer graphene. Several methods have been used for the controlled growth of the Bernal staked bilayer graphene, but it is still challenging to control the growth process. In this paper, we synthesize the large area Bernal stacked bilayer graphene using multi heating zone low pressure chemical vapor deposition (LPCVD). The synthesized bilayer graphenes are characterized by Raman spectroscopy, optical microscope (OM), scanning electron microscopy (SEM). High resolution transmission electron microscopy (HRTEM) is used for the observation of atomic resolution image of the graphene layers.