• 설비공학논문집
• /
• 제27권1호
• /
• pp.31-38
• /
• 2015

Geothermal heat pump (GHP) systems have become an efficient alternative to conventional cooling and heating methods due to their higher energy using efficiency. These systems use the ground as a heat source in heating mode operation and a heat sink in cooling mode operation. The aim of this study is to evaluate the heating performance of the GHP system for a residential building ($420m^2$) in Ulaanbaatar, Mongolia. In order to demonstrate the feasibility of a sustainable performance of this system, we installed the water-to-water geothermal heat pump with ten vertical ground heat exchangers and measured operation parameters from October 19, 2013 to March 26, 2014. The results showed that the entering source temperature of brine from the ground heat exchangers was in a range of the design target temperature of $-10^{\circ}C$ for heating. For total values of the representative results, the ground heat exchangers extracted heat of 53.51 MWh from the ground. In addition, the GHP system supplied heat of 83.55 MWh to the building and consumed power of 30.27 MWh. Consequently, the average heating seasonal performance factor ($SPF_h$) of the overall system was evaluated to be 2.76 during the measurement period of the heating season.

• 대한기계학회논문집A
• /
• 제34권12호
• /
• pp.1829-1836
• /
• 2010

지역난방은 열병합 발전소에서 생산된 열을 온수의 형태로 열배관 네트워크를 통해 넓은 지역에 일괄적으로 공급하는 난방시스템이다. 일반적으로 지역난방 열배관은 지중에 매설되며 내부를 흐르는 온수의 압력과 온도변화, 매설 토사와의 마찰 및 반력에 의한 하중을 받게 되므로 열공급 효율과 함께 기계적인 안전성에 대한 검토가 반드시 필요하다. 본 논문에서는 강관의 한계상태 설계법을 이용하여 한계판폭두께비와 한계변형률, 두 가지 관점에서 열배관의 국부좌굴 발생여부를 평가하였으며 그 결과 현재 국내에서 사용되고 있는 모든 열배관은 국부좌굴이 발생하지 않음을 확인하였다. 마지막으로 국부좌굴을 피하기 위한 최소 예열온도를 산출함으로써 예열온도에 대한 시공 기준을 제시하였다.

• Applied Microscopy
• /
• 제31권4호
• /
• pp.315-323
• /
• 2001

Kaolinite분말 시료를 이용한 TEM 직접 가열 실험에서 얻은 결론은 아래와 같다. (1) Gatan사의 가열 시료지지대에서 사용하고 있는 증류수 순환장치는 $500^{\circ}C$이상의 가열 실험에서 시료의 유동을 막는 필수적인 장비이다. (2) $600^{\circ}C$이하의 가열 실험에서는 분말의 두께에 따른 상전이 진행정도의 차이가 나타나기 때문에 앙은 시편과 두꺼운 시편을 고루 관찰하는 노력이 필요하다. (3) $900^{\circ}C$ 이상의 고온 가열 실험에서는 융점이 높은 Mo-grid의 사용이 필수적이다. 전체적으로 온도 상승률이나 온도 지속 시간이 상전이 과정에 미치는 영향이 증가하기 때문에 이들의 정량적인 제어가 가능한 자동제어방식의 사용이 필요하다. (4) 단면 관찰을 위해 고온용 epoxy에 포매된 kaolinite분말의 TEM가열 실험은 고온 가열시 epoxy의 유동 문제를 극복할 새로운 방법의 개발이 필요하다.

• 동아시아식생활학회지
• /
• 제23권2호
• /
• pp.203-210
• /
• 2013

In this study, cod bone were used as the main ingredient of a stock that can be eaten with Korean dried noodles. The stock was produced with heating for 30, 40, 50, 60, or 70 minutes using high-pressure extraction methods. Moisture content, chromaticity, pH, sugar content, salinity, mineral contents, quantitative analysis, and overall acceptance were studied to determine the optimal heating time. In our result, S1 the showed highest water contents 98.10%, while S5 showed the lowest moisture content (97.47%). There were no significant difference in pH between samples, while salinity and sugar content increased with increases in heating time. In terms of mineral contents, sodium and potassium showed proportional difference with increases in heating time, however, magnesium, calcium, and iron did not change. The results from a quantitative analysis test showed that transparency, fishy smell, delicate flavor, savory flavor, salt taste, and umami taste became stronger with increases in heating time increase. From the above results, the overall taste of the stock increases with increases in high-pressure heating time. Specifically, S4 high-pressure heating scored the highest on appearance, flavor, taste, after-taste, and overall acceptance. Thus, 60 minutes of high-pressure heating time is most desirable when producing stock with cod bones as a main ingredient.

• Journal of Welding and Joining
• /
• 제26권4호
• /
• pp.79-84
• /
• 2008

Use of sheet metal structure is increased in various fields such as automobile, aerospace and communication equipment industry. When this structure is welded, welding distortion is generated due to the non-uniformity of temperature distribution. Recently welding distortion becomes a matter of great importance in the structure manufacture industry because it deteriorates the product's quality by bringing about shape error. Accordingly many studies for solving the problems by controlling the welding distortion are being performed. However, it is difficult to remove all kinds of distortion by welding process, though various kinds of methods for reducing distortion are applied to production. Consequently, straightening process is operated if the high precision quality is requested after welding. The local heating method induces compression plastic deformation by thermal expansion in the heating stage and then leaves constriction of length direction in the cooling stage. Accordingly, in the case of sheet metal structure, straightening effect is expected by heating for the part of distortion. This study includes numerical analysis of straightening effect by the local heating method in distortion comes from production of welded sheet metal structure. Particularly straightening effect followed by dimensions of heating area is analyzed according to the numerical analysis. The numerical analysis is performed by constructing 3-dimensional finite element model for 0.4mm stainless steel-sheet metal. Results of this study confirm that straightening effect changes as heating area increases and the optimum value of heating area that proves the maximum straightening effect exists.

• 한국지열·수열에너지학회논문집
• /
• 제12권1호
• /
• pp.17-22
• /
• 2016

It is very important to obtain a out-of season production in horticultural greenhouses corresponding with higher crop prices. A ground source heat pump system has been highly spotlighed as an energy efficient heating system for the greenhouse. This paper investigated the operating cost of the ground source heat pump system with the variation of generating temperature and designing methods for heating system of the greenhouse. Even though the COP of the ground source heat pump system decreased with an increment of generating temperature in heating mode, the operating cost could be reduced. By adopting the high temperature heat pump system and heat storage tank, it could be achieved to save energy and reduce the operating time of auxiliary oil heating system for producing good plant-growth in the greenhouse.

• 비파괴검사학회지
• /
• 제27권3호
• /
• pp.268-279
• /
• 2007

The reliability of cold-bonding repair technique of carbon-fiber reinforced plastics (CFRP) laminates, often used as a temporary repair for the airplane maintenance, has been evaluated during cyclic loading and localized heating by nondestructive methods. Major concern was given to the evolution of damage after repair in the form of delaminations due to localized heating and cyclic loading combined. An area of interest both on the specimen repaired by cold-bonding and the specimen without repair where delaminations were induced by localized heating and cyclic loading was monitored by acoustic emission (AE) testing and further examined by pitch-catch low-frequency bond testing, and pulse-echo high-frequency ultrasonic testing. The results showed that the reliability of cold-bonding repair would be significantly reduced by the localized heating and cyclic loading combined rather than by the cyclic loading only. AE monitoring appeared to be an effective and reliable tool to monitor the integrity of temporarily repaired CFRP laminates in terms of the structural health monitoring (SHM) philosophy.

• 교육녹색환경연구
• /
• 제12권2호
• /
• pp.61-70
• /
• 2013

As the existing school building power consumption is expressed by total power consumption, in the view of energy saving is disadvantage. The the power consumption of school building is divided as cooling, heating, lighting and others. The cooling power consumption, heating power consumption, lighting power consumption can be calculated using real total power consumption that gained from Korea Electric Power Corporation(KEPCO). The power consumption for cooling and heating can be calculated using heat transmittance, wall area and floor area, and for lighting is calculated by artificial lighting calculation. but this calculation methods is difficult for laymen. This study was carried out in order to establish the regression equation for cooling power consumption, heating power consumption, lighting power consumption and other power consumption in school building. In order to verify the validity of the regression equation, it is compared regression equation results and calculation results based on real power consumption. As the results, difference between regression result and calculation results for cooling and heating power consumption showed 0.6% and 3.6%.

• 대한간호학회지
• /
• 제42권4호
• /
• pp.579-588
• /
• 2012

Purpose: The purpose of this study was to identify the effects of heating on the non-affected hand on blood flow velocity, wound healing, and pain for hand microsurgery patients. Methods: This study was designed using the nonequivalent control group pretest-posttest design. Thirty-nine patients were assigned either to the experimental group (20 patients) or control group (19 patients). Data were analyzed with $x^2$-test, Fisher's exact test, t-test, and repeated measure ANOVA using SPSS/WIN 17.0 program. Results: After treatment in this program, blood flow velocity (F=5.13, p=.008) and wound healing (F=4.11, p=.020) improved significantly in the experimental group compared to the control group. But there was no significant improvement in pain in the experimental group compared to the control group (F=2.40, p=.097). Conclusion: Based upon these results, the non-affected side hand heating was recommended as an independent nursing intervention for the patients who need improvement in blood flow velocity and wound healing such as patients who have microsurgery. As the heating was effective even when applied on the non-affected side, it is the applicable to patients who cannot tolerate any therapy on affected side.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.315-318
• /
• 2004

The Advantages of hot machining are the reduction of cutting forces, tool wear, and the increase of material removal rates. In this study, a hot-machining characteristics of milling by CBN tip was exprimentely analyzed, and the influence of the surface temperature and the depth of cut on the tool life were investigated. The selection of a heating method for obtaining ideal temperature of metals in machining is important. Faulty heating methods could induce unwanted structural changes in the workpiece and increase the cost. This study uses gas flame heating. It is obtained that tungsten carbide-alloyed has a recrystallisation temperature range of $800-1000^{\circ}C$ which is the high heating temperature that might induce unwanted structural changes. If it is performed at temperatures higher than $800^{\circ}C$ in machining, the possibility of unwanted structural changes and the increased wear of tool can be shown. Consequently, in hot machining of tungsten carbide-alloy, this study has chosen $400^{\circ}C-600^{\circ}C$ because the heating temperature might be appropriate in view of the cost and workpiece considerations. The results of this study experimentally shows a new machining method for tungsten carbide-alloyed that decreases the wear rate of machining tools