• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2006년도 춘계학술대회 논문집
• /
• pp.387-390
• /
• 2006

This paper presents a novel soft-switching PWM utility frequency AC to high frequency AC power conversion circuit Incorporating boost-half-bridge inverter topology, which is more suitable and acceptable for cost effective consumer induction heating applications. The operating principle and the operation modes are presented using the switching mode and the operating voltage and current waveforms. The performances of this high-frequency inverter using the latest IGBTs are illustrated, which includes high frequency power regulation and actual efficiency characteristics based on zero voltage soft switching (ZVS) operation ranges and the power dissipation as compared with those of the previously developed high-frequency inverter. In addition, a dual mode control scheme of this high frequency inverter based on asymmetrical pulse width modulation (PWM) and pulse density modulation (PDM) control scheme is discussed in this paper in order to extend the soft switching operation ranges and to improve the power conversion efficiency at the low power settings. The power converter practical effectiveness is substantially proved based on experimental results from practical design example.

• 멤브레인
• /
• 제7권2호
• /
• pp.65-74
• /
• 1997

자동차 배출가스로 인한 대기 오염을 줄일 수 있는 자동차 연료용 고순도 에탄올 농축을 의한 투과증발 pilot test가 발효에탄올 시작 공장에서 PVA 복합막을 이용하여 수행되었다. 약 95% 에탄올 농도를 갖는 에탄올/물 공비혼합물을 탈수, 농축하여 99% 이상의 연료용 고순도 에탄올을 얻는 투과증발 공정에서는 막의 내열 온도 범위 내에서 공급액의 가열 온도를 높일수록 농축 성능이 우수하였으며 투과액의 응축 온도는 경제성을 고려하여 결정해야 하며 $0{\circ}C$가 최적임을 알 수 있었다. 발효에탄올 농축을 위한 투과증발 성능은 합성에탄올 농축과 같은 결과를 보임으로써 투과증발 시스템 성능은 에탄올에 포함된 미량의 성분과는 무관한 결과를 보였으며, 투과증발 pilot test 결과 및 에너지 수지 관계를 이용하여 시스템에 소비되는 에너지의 대부분을 차지하는 투과액의 기화에 필요한 에너지는 공급액의 현열에 의해 공급됨을 확인하였다.

• 설비공학논문집
• /
• 제28권6호
• /
• pp.232-241
• /
• 2016

Installing a ventilator for an apartment house composed of over 100 dwelling units was mandated in 2006 to improve indoor air quality. In the case of mechanical ventilators, the air change rate is kept stable, however 68% of dwellers do not operate their ventilator because of an increased electrical bill and noise. In the case of natural ventilators, the former problems are settled, but there are concerns about cold draught and an increase of heating/cooling cost. Authors are developing a heat recovery type natural ventilator which is a natural ventilator equipped with total heat recovery element, and it is expected that those problems of mechanical ventilator and natural ventilator are resolved by this. The combined type diffuser of this study is an under developed fit to the heat recovery type natural ventilator above. There are no standards to evaluate the performance for this type of diffuser. Due to this issue this study investigated the performance of the ventilation and maintained a thermal environment for the combined type diffuser by comparing it with existing diffusers. The results revealed that the performances of the combined type of diffusers showed different features from the existing ones, and was estimated to be high enough in the performances above.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권6호
• /
• pp.103-110
• /
• 2021

유연한 고무재료와 강재 보강판을 적층으로 구성한 탄성받침은 우수한 수직강성과 유연한 횡강성으로 교량의 내진보강용으로 널리 사용되고 있다. 무엇보다 시공이 간단하고 비용이 높지 않다는 장점을 지니고 있다. 고무재료의 한 종류인 합성고무는 천연고무에 비해 노화에 대한 저항성이 크지만 이 역시 다양한 열화요인으로 성능이 저하된다. 내진설계기준 및 내진성능평가요령에서는 이러한 노화의 특성을 반영하고 있지 않지만 관련 연구가 축적되면 이를 반영하는 것이 합리적이다. 합성고무를 대상으로 노화촉진시간과 노출시간을 변수로 하여 노화촉진시험을 수행하여 전단특성의 변화를 분석하였다. 노화가 진행될수록 최대전단응력과 전단변형율은 감소한다. 또한 동일한 전단변형률에서 전단강성이 크게 증가한다.

• 전기전자학회논문지
• /
• 제23권1호
• /
• pp.295-301
• /
• 2019

바이오샘플의 DNA를 대량 증폭할 수 있는 휴대형 실시간 중합효소연쇄반응(Real-time PCR) 기기에서 히터는 PCR 반응 온도를 제어하기 위한 중요한 요소 중의 하나이다. 보통 빠른 히팅을 위해 소형 PCR 칩에 집적화되어 있고, 반도체 공정을 이용하여 박막형태로 제작되어 PCR 칩 제작 단가가 높은 편이다. 따라서 본 연구에서는 값싸고 온도제어를 정확히 할 수 있는 히터로 칩 저항을 사용하는 것을 제안한다. 칩 저항을 사용한 히터는 구조가 단순하고 제작이 쉽다는 장점이 있다. $2.54{\times}2.54cm^2$ 크기의 실시간 PCR 칩 위에 칩 저항을 1개 또는 2개를 사용했을 때 온도분포를 시뮬레이션 하였고, 고른 온도분포를 갖는 PCR 칩을 제작했다. 또한 효율적인 PCR 칩 냉각을 위해 소형 fan이 내장된 하우징을 설계하였고, 3D 프린터로 제작했다. 온도제어는 마이크로프로세서를 이용한 PID제어법(Proportional-Integral-Differential control)을 적용했다. 온도상승비와 하강비는 각각 $18^{\circ}C/s$, $3^{\circ}C/s$이며, 각 PCR 반응 단계의 유지 시간을 30초로 하였을 때, 한 사이클은 약 2.66분이 걸렸고, 35 사이클은 약 93 분 내로 진행할 수 있었다.

• Computers and Concrete
• /
• 제27권5호
• /
• pp.417-435
• /
• 2021

The optimal distribution of steel fibers over different layers of concrete can be considered as an appropriate method in improving the structural performance and reducing the cost of fiber-reinforced concrete members. In addition, the use of waste tire rubber in concrete mixes, as one of the practical ways to address environmental problems, is highly significant. Thus, this study aimed to evaluate the flexural behavior of functionally graded steel fiber-reinforced concrete containing recycled tire crumb rubber, as a volume replacement of sand, after exposure to elevated temperatures. Little information is available in the literature regarding this subject. To achieve this goal, a set of 54 one-, two-, and three-layer concrete beam specimens with different fiber volume fractions (0, 0.25, 0.5, 1, and 1.25%), but the same overall fiber content, and different volume percentages of the waste tire rubber (0, 5, and 10%) were exposed to different temperatures (23, 300, and 600℃). Afterward, the parameters affecting the post-heating flexural performance of concrete, including flexural strength and stiffness, toughness, fracture energy, and load-deflection diagrams, along with the compressive strength and weight loss of concrete specimens, were evaluated. The results indicated that the flexural strength and stiffness of the three-layer concrete beams respectively increased by 10 and 7%, compared to the one-layer beam specimens with the same fiber content. However, the flexural performance of the two-layer beams was reduced relative to those with one layer and equal fiber content. Besides, the flexural strength, toughness, fracture energy, and stiffness were reduced by approximately 10% when a 10% of natural sand was replaced with tire rubber in the three-layer specimens compared to the corresponding beams without crumb rubber. Although the flexural properties of concrete specimens increased with increasing the temperature up to 300℃, these properties degraded significantly with elevating the temperature up to 600℃, leading to a sharp increase in the deflection at peak load.

• 한국근적외분광분석학회:학술대회논문집
• /
• 한국근적외분광분석학회 2001년도 NIR-2001
• /
• pp.1618-1618
• /
• 2001

Predicting quality traits using near infrared (NIR) spectroscopy on whole grain samples has gained wide acceptance as a non-destructive, rapid and cost effective technique. Barley breeding programs throughout southern Australia currently use this technology as a tool for selecting malting quality lines. For the past 3 years whole grain barley calibrations have been developed at VIDA to predict malting quality traits in the early generation selections of the breeding program. More recently calibrations for whole grain malt have been developed and introduced to aid in selecting malted samples at the mid-generation stage for more complex malting quality traits. Using the same population set, barley and malt calibrations were developed to predict hot water extracts (EBC and IoB), diastatic power, free $\alpha$-amino nitrogen, soluble protein, wort $\beta$-glucan and $\beta$-glucanase. The correlation coefficients between NIR predicted values and laboratory methods for malt were all highly significant ($R^2$ > 0.84), whereas the correlation coefficients for the barley calibrations were lower ($R^2$ > 0.57) but still significant. The magnitude of the error in predicting hot water extract, diastatic power and wort $\beta$-glucan using whole grain malt was reduced by 50% when compared with predicting the same trait using whole grain barley. This can be explained by the complex nature of attempting to develop calibrations on whole grain barley utilizing malt data. During malting, the composition of barley is modified by the action of enzymes throughout the steeping and germination stages and by heating during the kilning stage. Predicting malting quality on whole grain malt is a more reliable alternative to predicting whole grain barley, although there is the added expense of micro-malting the samples. The ability to apply barley and malt calibrations to different generations is an advantage to a barley breeding program that requires thousands of samples to be assessed each year.

• 현장농수산연구지
• /
• 제10권1호
• /
• pp.169-181
• /
• 2008

The purpose of this study was to produce Pleurotus ostreatus using fermenter with bag cultivation. These results are as follows. 1. While mushroom composts were being fermented in a fermenter, the physical property of the fermented composts was getting better when there isn't any screw or revolving flies in the fermenter and the strength of pressing the composts was getting less. 2. The composts were fermented well as slaked lime of 1% density added to the composts. 3. According to the result of examining our fermenting ways, composts were in the best condition after being fermented for 48 hours since the temperature in a fermenter has come to 60℃, which could be reached by heating the fermenter by 40℃ after putting compost materials and water into it. 4. The good condition of fermenting could be maintained by controlling the speed of revolving flies, therefore the speed be down when the temperature is above 60℃ and up bellow 60℃. 5. Since the composts had been added with 1.5~2% of cottonseed meal or rice bran, the fermented composts were in good condition and also the quantity and quality of the mushroom produced on the fermented composts were satisfied. 6. There were needed 7 hours of labour for 3days from the first day of putting composts into a fermenter for fermenting 3.5M/T(10,000~12,000bags of 750~800g per bag) of composts to the third day of finishing the fermenting work, and also the cost was 112,066￦(130$) including 52,066￦(60$) of electric charge and fuel expense.

• 한국지반공학회논문집
• /
• 제26권2호
• /
• pp.33-43
• /
• 2010

지열은 고효율 신재생에너지로 각광을 받고 있으며 건축물의 냉난방 설비 시스템으로 활용이 점차 확산되고 있다. 지열 히트펌프 중에서 지하수를 열원으로 사용하는 단일심정(Standing column well)은 특히 효율이 높고 초기설치비용이 저렴하며 국내 지반 수리조건에 적합하다. 반면, 국내에는 아직 SCW의 성능을 평가할 수 있는 수치해석 모델이 없으며 국내 자료를 적용한 수치해석이 수행된 바 없다. 본 연구에서는 SCW 수치해석 모델을 유한체적해석 프로그램을 이용하여 구축하였다. 수치적 모델은 수리 열 연계해석을 수행하여 열이류, 대류, 전도를 모두 모사한다. SCW 모델은 미국과 국내에서 계측된 현장 데이터를 통하여 검증하였다. 비교 결과 본 연구에서 구축된 수치해석 모델은 정확하게 SCW의 거동을 예측할 수 있는 것으로 나타났다. 검증된 수치해석 모델은 동반논문에서 매개변수연구에 활용되었다.

• 한국재료학회지
• /
• 제34권6호
• /
• pp.267-274
• /
• 2024

In this study, four different samples of Se₆₀Ge_40-xBi_x chalcogenides glasses were synthesized by heating the melt for 18 h in vacuum Pyrex ampoules (under a 10^-4 Torre vacuum), each with a different concentration (x = 0, 10, 15, and 20) of high purity starting materials. The results of direct current (DC) electrical conductivity measurements against a 1,000/T plot for all chalcogenide samples revealed two linear areas at medium and high temperatures, each with a different slope and with different activation energies (E₁ and E₂). In other words, these samples contain two electrical conduction mechanisms: a localized conduction at middle temperatures and extended conduction at high temperatures. The results showed the local and extended state parameters changed due to the effective partial substitution of germanium by bismuth. The density of extended states N(E_ext) and localized states N(E_loc) as a function of bismuth concentration was used to gauge this effect. While the density of the localized states decreased from 1.6 × 10¹⁴ to 4.2 × 10¹² (ev^-1 cm^-3) as the bismuth concentration increased from 0 to 15, the density of the extended states generally increased from 3.552 × 10²¹ to 5.86 × 10²¹ (ev^-1 cm^-3), indicating a reduction in the mullet's randomness. This makes these alloys more widely useful in electronic applications due to the decrease in the cost of manufacturing.