• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.647-653
• /
• 2000

In this research the heat regenerative technology was employed to eliminate frosting on evaporator coil and improve COP of the heat pump system. This heat regenerative device(HRD) has very simple structure consisting a geared motor and a porous fiber belt passing through alternatively between cold and warm air duct. The laboratory test showed that the heat pump system with HRD yielded an impressive COP higher than 3.5 at the outside air temperature of $-7^{circ}C$ in heating mode.

• 설비공학논문집
• /
• 제22권7호
• /
• pp.460-467
• /
• 2010

In housing units constructed recently in Korea, the length of ondol coil is different in each room, so the flow rate of hot water is adjusted by setting valve opening. If the flow rate is not appropriate for heating load, the room temperature seriously deviates from the set temperature range for comfort. In particular, too small valve opening can induce a noise by cavitation. In order to adjust the valve opening, two methods by zone area and a new method by return temperature rise were modelled and simulated using TRNSYS and EES. As a result, heating energy consumption during one week was the same on three methods, but the room temperature of the new method minimally deviated from the range of set temperature with a low possibility of noise.

• 소성∙가공
• /
• 제12권5호
• /
• pp.457-464
• /
• 2003

In the powder compact melting technique, proper precursor fabrication is very important because density distribution after foaming and foamability are determined during precursor fabrication process. The fabrication of the precursor has to be performed very carefully because any residual porosity or other defects will lead to poor results in further processing. In order to evaluate the effect of the compaction parameters on the kinetics of the foaming process, a series of experiments were performed. In this study, aluminium foams with a closed cell structure were fabricated by using both the powder compact method and the induction heating process. A proper induction coil was designed to obtain a uniform temperature distribution over the entire cross sectional area of precursor. To establish the foamable precursor fabrication conditions, effects of process parameters such as the titanium hydride content (0.3∼1.5 wt.%), pressing pressure of the foamable precursor (50∼150kN) on the pore morphology were investigated.

• 한국정보통신학회논문지
• /
• 제14권3호
• /
• pp.729-736
• /
• 2010

본 연구에서는, 펄스포밍 제어기술과 펄스 성형을 가지는 자기 자극장치에 대해 언급 하고자 한다. 자기자극장치는 5-100초 사이에 펄스성형 기술적용과 순간적 방전코일 전류 6kA까지 상승되므로 스너버 회로를 가지는 IGBT 전력소자를 사용하였다. 57-67%의 열손실을 줄였고, 2-34%의 적은 에너지를 사용한 유도전계펄스로 전형적인 코사인 펄스와 매칭 되는것을 알수가 있었다. 자기자극장치는 펄스성형하는 기술 증가와 함께 한계 펄스진폭의 예측 되는 감소인 20-100초 사이에서 펄스성형 기술을 운동신경에 활발한 자극하기 위하여 사용된다. 자기 자극장치 프로트 타입에서 이용된 기초과학 기술에 의하여 기능을 확장할 수 있고, 전력소비를 줄일 수 있었고, 자기자극장치의 열손실에 대해서도 축소할 수가 있어, 더 나은 연구와 치료에 통해 응용할 수가 있다.

• 대한조선학회논문집
• /
• 제42권3호
• /
• pp.241-248
• /
• 2005

The induction heating is more efficient for a plate bending because of its easy operation and control of working parameters compared with the heating by torch. In this study, a more efficient method was proposed for the prediction of plate bending. The existing analysis method using the axi-symmetric coil model could not handle the varying temperature during the heating and the forming process for curved plates like a saddle or a concave type curvature. The proposed method using some discrete steps in this study could overcome these difficulties and show more accurate, reasonable results in temperatures and deflections of fiat or curved plates. This method is composed of multi-disciplinary analyses such as an electro-magnetic analysis, a heat transfer analysis and a deformation analysis based on inherent strain approach.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.411-416
• /
• 2006

In this paper, we performed the experimental and numerical study on the thermal comfort(TC) and indoor air quality(IAQ) in the lecture room with a different airflow rate of the ventilation system and heating system for heating season. Through the experimental results, we found out that there was considerably difference of the PMV but there was little difference of $CO_2$ concentration with a different heating system. From a numerical results, the best operating condition was that discharge airflow rate of SAC is 29 CMM and supply airflow rate of the ventilation system is 1,200 CMH from a viewpoint of TC and IAQ.

• 한국환경보건학회지
• /
• 제39권3호
• /
• pp.268-278
• /
• 2013

Objectives: The purpose of this study was to apply the Hazard Analysis Critical Control Point (HACCP) system to the production of seasoned laver products. The hazard analysis examined microbial evaluations and developed a HACCP management plan through the heating process. Methods: In this study we chose three companies and performed the analysis thrice. During this study, general bacteria along with other food poisoning bacteria such as Salmonella spp., Staphylococcus aureus, Listeria monocytogenes, Bacillus cereus, E.coil, O157:H7, Vibrio parahaemolyticus, were studied at varying temperatures from 100 to $300^{\circ}C$. Results: The presence of general bacteria was detected in raw laver in the samples analyzed from all the three companies, and the number ranged from $10^5-10^7$. Bacillus cereus was detected in samples from only two of the three companies analyzed. However, Salmonella spp., Staphylococcus aureus, Listeria monocytogenes, E.coil, O157:H7, and Vibrio parahaemolyticus were all negative. General bacteria was reduced to $10^5$ after being subjected to temperatures of $100-250^{\circ}C$, but heating to over $270^{\circ}C$ reduced the number to below $10^3$, and the other microbes such as Bacillus cereus were not detected. Conclusions: In conclusion, the heating process ($270-280^{\circ}C$) along with RPM of 100-1200 were identified as CCP to reduce biological hazards.

• Progress in Superconductivity
• /
• 제13권2호
• /
• pp.111-116
• /
• 2011

Since superconducting wires have no resistance, electromagnets based on the superconducting wires produce no resistive heating with DC current as long as the current does not exceed the critical current of the wire. However, unlike resistive wires, superconducting wires exhibit AC heat loss. Embedding fine superconducting filaments inside copper matrix can reduce this AC loss to an acceptable level and opens the way to AC-capable superconducting coils. Here, we introduce an easy and accurate method to measure AC heat loss from sample superconducting coils by measuring changes in the rate of gas helium outflow from the liquid helium dewar in which the sample coil is placed. This method provides accurate information on total heat loss of a superconducting coil without any size limit, as long as the coil can fit inside the liquid helium dewar. With this method, we have evaluated AC heat loss of two superconducting solenoids, a 180-turn solid NbTi wire with 0.127 mm diameter (NbTi coil) and a 100-turn filamented wire with 1.4 mm diameter where 7 NbTi filaments were embedded in a copper matrix with copper to NbTi ratio of 6.7:1 (NbTi-Cu coil). Both coils were wound on 15 mm-diameter G-10 epoxy tubes. The AC heat losses of the NbTi and NbTi-Cu coils were evaluated as $53{\pm}4.7\;{\mu}W/A^2Hzcm^3$ and $0.67{\pm}0.16\;{\mu}W/A^2Hzcm^3$, respectively.

• 한국산학기술학회논문지
• /
• 제16권7호
• /
• pp.4381-4387
• /
• 2015

선체의 외판은 복잡한 곡면 형상이며 대부분의 조선소에서는 이의 제작을 위해 가스 토치를 이용한 선상 가열 방법을 사용하고 있다. 가스 토치를 이용한 전통적인 선상 가열 방법은 입열량의 제어가 어려울 뿐만 아니라 고압의 가스 분출에 따른 소음과 대기 오염 등 열악한 작업 환경의 문제점을 안고 있다. 최근에는 입열량의 제어가 비교적 용이하고 친환경적인 고주파 유도 가열에 주목하여 이를 가열 열원으로 하는 강판의 성형 자동화 연구들이 진행되고 있다. 본 연구에서는 강판의 곡면 성형을 위한 유도 가열 시뮬레이션 방법을 개발하였으며 유도 가열 실험 결과와 비교하여 그 유효성을 검증하였다. 개발된 유도 가열 시뮬레이션 방법은 효율적인 유도 가열 코일 설계와 최적 성형 조건 산출 등 유도 가열을 이용한 선체 외판의 곡가공 자동화 시스템 개발에 유용한 해석적 툴로 활용될 수 있을 것으로 기대된다.

• 전력전자학회논문지
• /
• 제10권5호
• /
• pp.481-487
• /
• 2005

제안한 유도가열 시스템은 증류탑 장치에 사용되는 특수충진체에 의한 열교환기술과 IH(Induction-Heating)전자유도가열용의 특수한 고주파 전력회로 기술을 응용한 차세대 가열방식이다. 특히 일체의 연소과정이 없다는 점에서 작업환경의 개선이 가능하며 본 기술은 IGBT대응의 고주파 인버터를 사용하여 상용교류로부터 수[kHz]의 고주파 교류를 발생시킬 수 있다. 본 논문에서는 절연체 용기 내에 특수 스텐레스 발열체부하를 수납하여 용기 외부의 고주파 공진형 인버터 접속의 워킹코일로부터 비접촉 상태로 전자유도 와전류를 구조체에 흘림으로서 발열하게 되는 새로운 유체가열방식을 제안한다. 그리고 5[kW]급 풀-브릿지 공진형 인버터 시스템과 공진부하의 동작해석, 특성분석 및 본 시스템을 이용한 고효율 스팀 발생장치의 개발과 시스템의 응용에 대해 논하였다.