• 전자공학회논문지
• /
• 제53권6호
• /
• pp.155-166
• /
• 2016

전자유도 가열시설에서 정밀하고 일정한 주파수 성분에 의해 가열물체에 발열을 유도하려면 LC공진회로 설계단계에서 출력 주파수에 대한 커패시터의 정전용량(C)과 워크코일의 유도계수(L) 설정이 중요하다. 하지만 고유의 발열계수를 가진 물체의 가열위치와 범위에 직접유도를 하는 워크코일은 고정적으로 설계되는 반면 커패시터는 가변되도록 설계되어야만 전체장비의 활용도가 높아진다. 본 논문에서는 $1000V_{MAX}$ 최대전압과 $200I_{MAX}$ 전류에서 최대 700kHz의 고주파 LC공진 출력이 되도록 커패시터 내부구성 원자재 선정 및 공정설계 단계까지 단일전극 용량별 샘플을 추출하였다. 그리고 정전용량 규격변화에 따라 주파수 변화특성과 출력 파라메타 결과를 바탕으로 HF-LC공진용 전도냉각 커패시터의 최적설계를 위한 관계를 증명하는 기초 실험결과를 제시하였다.

• 한국광학회지
• /
• 제20권5호
• /
• pp.266-271
• /
• 2009

본 논문에서는 높은 소멸비뿐만 아니라 낮은 파워 소모를 가지는 방향성 결합기 구조의 열광학 스위치를 설계하였다. 설계된 스위치는 전극의 열발생 유무에 따라 폴리머의 굴절률이 변하는 열광학 효과를 이용하여 동작한다. 전극에 파워가 인가되지 않으면(OFF), 입사된 빛은 반대쪽 도파로로 대부분 전이된다. 전극에 일정수준 이상으로 파워가 인가되면(ON), 입력 도파로로 입사된 빛은 반대쪽 도파로의 굴절률이 낮아져 입력 도파로로 진행한다. 방향성 결합기 스위치는 소멸비 일반화 곡선과 입력 도파로의 수평이동 방법을 이용하여 설계되었다. 결합길이는 1,610 ${\mu}m$, on과 off 상태의 소멸비는 각각 -28, -30 dB로 설계되었다. 또한, 본 논문에서 전극 구조는 열분석을 통해 최적화되었다. 전극의 폭(w)이 증가하고 전극과 도파로의 중심간격(d)이 감소할수록 도파로로 전달되는 열은 증가하였다. 전극에서 발생된 열은 반대쪽 도파로에도 영향을 주기 때문에 두 도파로간의 온도차이는 주어진 w와 d에 따라 변한다. 이때, 최대의 온도차이를 보이는 특정한 조건이 존재하였다. 최대 온도차이는 전극의 폭이 넓을수록, 전극의 온도가 높을수록 증가한다. 특히, 스위칭에 필요한 온도차이를 최대 온도차이 조건으로 설계하면 전극의 온도를 낮출 수 있다. 최대 온도차이 조건은 열광학 스위치의 파워소모를 감소시키는 방안이 될 것으로 기대된다.

• Transactions on Electrical and Electronic Materials
• /
• 제13권4호
• /
• pp.185-187
• /
• 2012

Ga doped ZnO (GZO)/copper (Cu) bi-layered film was deposited on glass substrate by RF and DC magnetron sputtering and then the effect of the Cu bottom layer on the optical, electrical and structural properties of GZO films were considered. As-deposited 100 nm thick GZO films had an optical transmittance of 82% in the visible wavelength region and a sheet resistance of 4139 ${\Omega}/{\Box}$, while the GZO/Cu film had optical and electrical properties that were influenced by the Cu bottom layer. GZO films with 5 nm thick Cu film show the lower sheet resistance of 268 ${\Omega}/{\Box}$ and an optical transmittance of 65% due to increased optical absorption by the Cu metallic bottom layer. Based on the figure of merit, it can be concluded that the thin Cu bottom layer effectively increases the performance of GZO films as a transparent and conducting electrode without intentional substrate heating or a post deposition annealing process.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 하계종합학술대회 논문집(2)
• /
• pp.383-386
• /
• 2004

The one of important requisites for fabricating molecular electronic device is the single crystal direction of bottom substrate nowadays. [1,2]. We obtain the optimum SAM result when the Au crystal is <111> structure for Self-Assembled molecular. To get the <111> crystal Au, we generally repeat heating and cooling course after evaporating Au [3]. However, we can fabricate <111> crystal Av thin film except post treatment because we simultaneously evaporate and anneal using Effusion Cell. In this paper, we study on thin film growth of <111> crystal Au as bottom electrode which is essential for Self-Assembled molecular by Effusion Cell and analyze crystal structure, thickness, surface conductivity and so on as each process condition.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.504-507
• /
• 2004

Previous studies on the liquid Gallium ion sources used an electro-chemically etched tungsten wire with a coil-type heater. Such a structure requires excessive power consumption in the course of heating the liquid metal. In this work, a new structure is proposed that replaces the coil-type heater. It uses a Gallium reservoir made of six pre-etched 250 $\mu\textrm{m}$ tungsten wires that surround the needle electrode. Gallium loading at the reservoir is observed to be much more stable, resulting in an improved beam stability.

• 센서학회지
• /
• 제13권4호
• /
• pp.292-297
• /
• 2004

Carbon nanotubes (CNT) were synthesized by arc-discharge method. To fabricate CNT sensor, CNT powder was dispersed in ${\alpha}$-Terpinol($C_{10}H_{17}OH$) solution. The CNT tilms were fabricated by screen printing method on the interdigitated Pt/Pd alloy electrode. The microstructure of CNT film was observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). In order to investigate the gas sensing characteristics of the film, the CNT film was experimented to measure NO response and recovery time. The CNT sensor with a heater was compared to that without a heater. And this sensor shows better reproductibility and faster recovery time than another CNT sensors. We suggest the possibility to utilize a CNT as new sensing materials for environmental monitoring.

• 전기학회논문지
• /
• 제62권7호
• /
• pp.980-986
• /
• 2013

In this paper, the discharge characteristics of ac-type cylindrical discharge devices with diameters (D) in the $50{\sim}400{\mu}m$ range have been investigated numerically. The cylindrical devices have much lower breakdown voltages compared to the coplanar electrode structures. The breakdown voltage of the cylindrical structures increases with the decrease of diameters in $50{\sim}100{\mu}m$ range. In $100{\sim}200{\mu}m$ range, however, the breakdown voltage decreases slightly with the decrease of diameters. Also, as the diameter gets smaller, the electron heating efficiency is greatly improved.

• International Journal of Safety
• /
• 제11권2호
• /
• pp.5-9
• /
• 2012

The discharge properties of super high-pressure mercury lamp are due to resistance heating for energy input, and results in temperature increase. The cooling equilibrium state is reached by the heat conduction, convection and radiation. In order to predict the fluid flow and heat transfer in and around the mercury lamp accurately, its visualization is of utmost importance. Such visualization is carried out by CFD program in this study. We focus on Anode shape to calculate four cases, namely AA, AB, AC and AD separately, and compare the temperature distribution and velocity vector in each case to predict cooling capacity and fluid flow properties. It can be concluded that the shape of anode plays an important role that affects the fluid flow and heat transfer in a mercury lamp.

• Journal of Welding and Joining
• /
• 제21권2호
• /
• pp.70-75
• /
• 2003

Spot welding is a process that sheet metals are joined in one or more spot by heating at the faying interface. In this process, the spatter is dispersed from melted area. It has been reported that spatter generation has adverse effects on weld quality. However, no systematic study has been carried out to find out its effect on weld quality in resistance spot welding processes. In this study, specially designed specimen are used to perform experimental investigation of spatter generation and its effect. Major finding of this study show trends in tensile-shear strength for various amounts of spatter generated during spot welding process. Thus, optimum welding conditions are proposed in view of spatter generation and tensile-shear strength. (Received December 11, 2002)

• Journal of the Optical Society of Korea
• /
• 제19권1호
• /
• pp.88-94
• /
• 2015

This paper reports the fabrication of a lenticular liquid crystal (LC) lens array with thermally tunable focus and with the function of a convertible lens type, using the surface structure of a UV-curable polymer and a twisted-nematic (TN) LC cell. The TN LC cell makes the LC lenticular lens function as a converging or diverging lens by controlling electrically the polarization of input light. Therefore, the focal lengths for both the converging and diverging lenses, which can be switched from the TN cell, can be tuned by changing the effective refractive index of the LC by Joule heating of the transparent electrode. As a result, the focal length of the lens with the E7 LC was changed continuously from 8.7 to 31.2 mm for the converging lens type and from -9.8 to -14.2 mm for the diverging lens when the temperature was increased from 25 to $56^{\circ}C$.