• 한국수산과학회지
• /
• 제33권5호
• /
• pp.399-402
• /
• 2000

일반적인 수산물 통조림의 내용물 속에는 물, 기름 및 조미액즙 등 packing medium이 들어있다. 본 연구에서는 새우, 꽁치 및 굴을 원료로 건조 및 조미 후 packing medium이 없는 새로운 형태의 조미통조림을 제조하고 이들 제품의 진공도별 (15, 30, 45 및 60cmHg) 열침투 특성을 조사할 목적으로 본 연구를 수행하였다. 진공도별 제품의 열침투 속도는 진공도가 높을수록 빠르게 나타났으며 동일시간 살균했을 때 진공도가 높을수록 Fo치가 높게 나타났다. 한편 상법으로 제조된 water pack과 본 시험에서 제조한 조미통조림과의 열침투 속도를 비교했을 때 새우와 꽁치 조미통조림의 경우는 진공도 15cmHg 이상에서는 열침투 속도가 water pack 제품보다는 빠르게 나타났고 굴 제품의 경우는 water pack 제품이 30cmHg 이상에서 열침투 속도가 빠르게 나타났다. 따라서 packing medium이 없는 조미 통조림의 경우 진공도 30cmHg 이상이 되면 기존의 water pack 제품보다 열침투 속도가 빠르다는 사실이 관찰되었다.

• 한국재료학회지
• /
• 제28권9호
• /
• pp.522-527
• /
• 2018

This study investigates the effects of isothermal holding temperature and time on the microstructure, hardness and Charpy impact properties of medium-carbon bainitic steel specimens. Medium-carbon steel specimens with different bainitic microstructures are fabricated by varying the isothermal conditions and their microstructures are characterized using OM, SEM and EBSD analysis. Hardness and Charpy impact tests are also performed to examine the correlation of microstructure and mechanical properties. The microstructural analysis results reveal that granular bainite, bainitic ferrite, lath martensite and retained austenite form differently in the specimens. The volume fraction of granular bainite and bainitic ferrite increases as the isothermal holding temperature increases, which decreases the hardness of specimens isothermally heat-treated at $300^{\circ}C$ or higher. The specimens isothermally heat-treated at $250^{\circ}C$ exhibit the highest hardness due to the formation of lath martensite, irrespective of isothermal holding time. The Charpy impact test results indicate that increasing isothermal holding time improves the impact toughness because of the increase in volume fraction of granular bainite and bainitic ferrite, which have a relatively soft microstructure compared to lath martensite for specimens isothermally heat-treated at $250^{\circ}C$ and $300^{\circ}C$.

• 한국화재소방학회논문지
• /
• 제9권1호
• /
• pp.10-19
• /
• 1995

Study on combined natural convection-radiation In partially open square enclosures filled with absorbing-anisotropic scattering media is performed. A heater block located in the enclosure causes the natural circulation of the fluid in the enclosure which results In significant in-flow of the cold fluid through the partially open wall. Four different locations of the heater are considered to observe the effect of the heater locations on the resulting heat transfer. Results obtained from the combined convection-radiation analyses show much stronger circulation of t he fluid inside the enclosure as compared to those obtained from the pure convection analyses. As the ratio of the open area is Increased, the inflow of the cold fluid and the circulation of the fluid inside the enclosure is increased causing lower fluid temperature Inside the enclosure. It is shown that the location of the heater influences the circulation and heat transfer significantly by showing stronger circulations and more uniform temperature distributions for the cases where the heater is located on the bottom wall as compared to those for the cases where the heater is located on the upper part wall of the enclosure. For pure absorbing medium, the expected circulation in the fluid is relatively week as compared to those with absorbing-scattering medium due to the smaller wall heating as the radiant heat is used to heat the fluid instead. The forward anisotropic scattering phase function is shown to increase the fluid circulation further as compared to the isotropic scattering medium.

• 대한기계학회논문집B
• /
• 제27권5호
• /
• pp.543-552
• /
• 2003

The effects of a directionally emitting and reflecting dielectric surface on the wall heat flux and medium temperature distribution are studied. The system is an infinite square duct enclosing an absorbing and emitting medium. The emissivity and reflectivity of opaque and gray wall vary with direction. Combined effect of conductive and radiative heat transfer is analyzed using finite difference and the direct discrete-ordinates method. The parameters under study are conduction to radiation parameter, optical depth, refractive index ratio. The results with directional and diffuse properties deviate each other when the conduction to radiation parameter is less than around 0.01. The wall heat flux differs fur optical thickness less than around 0.1. However, the medium temperature profiles differ for optical thickness greater than around 1. Deviations from diffuse property calculations are larger for hot wall with directional property than cold wall with directional property. As n increases from 1.5, the trend changes are observed fur refractive index ratio about n=6.10

• 한국정밀공학회지
• /
• 제22권11호
• /
• pp.51-58
• /
• 2005

Laser surface hardening technologies have been used to improve characteristics of wear and to enhance the fatigue resistance for automotive parts. The objective of this research work is to investigate the influence of the process parameters, such as power of laser and defocused spot position, on the characteristics of laser heat treatment for the case of SM45C medium carbon steel. CW Nd:YAG laser is selected as the heat source. The optical lens with the elliptical profile is designed to obtain a wide heat treatment area with a uniform hardness. From the results of the experiments, it has been shown that the maximum hardness is approximatly 780 Hv when the power and the travel speed of laser are 1,095 W and 0.6 m/min, respectively. In addition, the hardening width using the elliptical lens was three time larger than that using the defocusing of laser beam.

• 한국자동차공학회논문집
• /
• 제22권7호
• /
• pp.63-69
• /
• 2014

Domestic automobile companies have adopted drum type brake system for commercial vehicles. However recently those companies have been applying disc-brake system to solve vehicle control-instability and inefficient heat discharge performance of conventional drum brake system for a medium commercial vehicle. Because the kinetic energy of a running commercial vehicle is relatively high, the brake system should discharge lots of heat energy while braking. A ventilated type brake disc has been used to increase heat discharge performance of a brake system. The vent structure of a disc highly affects cooling efficiency. This paper compares thermal characteristics of three types of vent structure in JASO C421 braking condition. It is found that the slant bend type disc has the lowest temperature and thermal stress distributions in the braking condition.

• 한국유기농업학회지
• /
• 제31권4호
• /
• pp.427-439
• /
• 2023

The silverleaf whitefly, Bemisia tabaci, is a major pest distributing worldwide damaging over 900 host plant species, and is highly resistant to chemical pesti- cides. Due to the high pesticide resistance of whitefly, there is a need for alternatives to chemical control. Entomopathogenic fungi are candidates for biological pesticide that can overcome the resistance problem of chemical pesticide. Therefore, in this study, we tested pathogenicity of the entomopathogenic fungi to select high insec- ticidal activity against whitefly. As a result, IPBL-C (Cordyceps fumosorosea) and IPBL-F (Metarhizium pinghaense) isolates showed high insecticidal activity against whitefly. Additionally, as a result of culturing the selected isolates on spent coffee grounds medium, the conidia of IPBL-F produced on coffee grounds medium showed five times higher heat stability after heat treatment at 45℃ for one hour than conidia produced on PDA medium.

• 조명전기설비학회논문지
• /
• 제28권7호
• /
• pp.1-12
• /
• 2014

This paper is proposed to design the new heat-sink apparatus for improving the heat transfer characteristics in the power LED chip, and results of the operation characteristics were discussed. The core design is that the soldering through-hole on the FR-4 PCB board is formed to the effective heat transfer. That is directly filled with Ag-nano materials, which shows the high thermal conductivity. The heat transfer medium consisting of Ag-nano materials is classified into two structures. Mediums are called as the heat slug and the multi-pin in this work. The heat of the high temperature generated from the LED chip was directly transferred to the heat slug of the one large size. And the accumulated heat from the heat slug was quickly dissipated by the medium of the multi-pin, which is the same body with the heat slug. This multi-pin was designed for the multi-dissipation of heat by increasing the surface areas with a little pins. Subsequently, the speed of the heat transfer with this new heat-sink apparatus is three times faster than the conventional heat-sink. Therefore, the efficiency of the illuminating light will be improved by adapting this new heat-sink apparatus in the large area's LED.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2408-2413
• /
• 2007

Since the heat generation in a chip increases as the components are miniaturized and the computing speed becomes faster, suitable heat dissipation has become one of the primary limiting factors to ensure the reliable operation of the electronic devices. A pin-fin array could be used as an alterative cooling system of the electronic equipment. In this study, convective heat transfer through the pin-fin array is analyzed experimentally based on porous medium approach. The influence of the structure of the pin-fin array including the pin-fin spacing, the pin diameter and plate length on heat transfer characteristics is investigated and compared with the previous analytical results and existing correlation equations. Nowadays, electronic and mechanical devices become smaller and smaller. In this sense, the main purpose of this study is to decide the optimum pin-fin arrangement to get similar heat transfer performance when the length of the existing cooling system is reduced as a half.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제16권2호
• /
• pp.125-135
• /
• 2012

The transient magnetohydrodynamic (MHD) generalized Couette flow with heat transfer through a porous medium of an electrically conducting, viscous, incompressible fluid bounded by two parallel insulating porous plates is studied in the presence of uniform suction and injection and a heat source considering the Hall effect. A uniform and constant pressure gradient is imposed in the axial direction and an externally applied uniform magnetic field as well as a uniform suction and injection are applied in the direction perpendicular to the plates. The two plates are kept at different but constant temperatures while the Joule and viscous dissipations are included in the energy equation. The effect of the Hall current, the porosity of the medium and the uniform suction and injection on both the velocity and temperature distributions is investigated.