• Korean Journal of Food Science and Technology
• /
• v.37 no.3
• /
• pp.438-442
• /
• 2005

Granule swelling is essential phenomenon of starch gelatinization in excess water, and characteristic of heated starch dispersion depends largely on size and distribution of swelled starch granule. Although swelling characteristic of starch granules depends on type of starch, heating rate, and moisture content, influence of heating rate on swelling phenomenon of starch granule has not been fully discussed, because constant heating rate of starch dispersion cannot be obtained by conventional heating method. Ohmic heating, electric-resistant heat generation method, applies alternative current to food materials, through which heating rate can be easily controlled precisely and conveniently at wide range of constant heating rates. Starch dispersion heated at low heating rates below $7.5^{\circ}C/min$ showed Newtonian fluid behavior, whereas showed pseudoplastic behavior at heating rates above $16.4^{\circ}C/min$. Apparent viscosity of starch dispersion increased linearly with increasing heating rate, and yield stress was dramatically increased at heating rates above $16.4^{\circ}C/min$. Average diameter of corn starch granules during ohmic heating was dramatically increased from $30.97\;to\;37.88\;{\mu}m$ by increasing heating rate from $0.6\;to\;16.4^{\circ}C/min$ (raw corn starch: $13.7\;{\mu}m$). Hardness of starch gel prepared with 15% corn starch dispersion after heating to $90^{\circ}C$ at different heating rates decreased gradually with increasing heating rate, then showed nearly constant value from $9.4\;to\;23.2^{\circ}C/min$. Hardness increased with increase of heating rate higher than $23.2^{\circ}C/min$.

• Korean Journal of Remote Sensing
• /
• v.33 no.6_2
• /
• pp.1101-1118
• /
• 2017

Temperatures in urban areas are steadily rising due to rapid urbanization and on-going climate change. Since the spatial distribution of heat in a city varies by region, it is crucial to investigate detailed thermal characteristics of urban areas. Recently, many studies have been conducted to identify thermal characteristics of urban areas using satellite data. However,satellite data are not sufficient for precise analysis due to the trade-off of temporal and spatial resolutions.In this study, in order to examine the thermal characteristics of Daegu Metropolitan City during the summers between 2012 and 2016, Moderate Resolution Imaging Spectroradiometer (MODIS) daytime and nighttime land surface temperature (LST) data at 1 km spatial resolution were downscaled to a spatial resolution of 250 m using a machine learning method called random forest. Compared to the original 1 km LST, the downscaled 250 m LST showed a higher correlation between the proportion of impervious areas and mean land surface temperatures in Daegu by the administrative neighborhood unit. Hot spot analysis was then conducted using downscaled daytime and nighttime 250 m LST. The clustered hot spot areas for daytime and nighttime were compared and examined based on the land cover data provided by the Ministry of Environment. The high-value hot spots were relatively more clustered in industrial and commercial areas during the daytime and in residential areas at night. The thermal characterization of urban areas using the method proposed in this study is expected to contribute to the establishment of city and national security policies.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.3
• /
• pp.271-282
• /
• 2020

Sewage treatment plants are social infrastructure of cities. The sewage distribution rate in Korea is reaching 94% based on the sewage statistics based in the year of 2017. In Korean sewage treatment plants, use of PAC (Poly Aluminum Chloride) accounts for 58%. It contains a large amount of impurities (heavy metal) according to the quality standards, however, there have been insufficient efforts to reinforce the standards or technically improve the quality, which resulted in secondary pollution problems from injecting excessive coagulant. Also, the increase in the use of chemicals is leading to the increases in the annual amount of sewage sludge generated in 2017 and the need to reuse sludge. As such, this study aims to verify the possibility of reusing sludge by evaluating the stability of heavy metals based on the injection of coagulant mixture during water treatment which uses the torrefield wood powder and natural materials, and evaluating the sedimentation and heating value of sewage sludge. As a result of analyzing heavy metals (Cr, Fe, Zn, Cu, Cd, As, Pb, and Ni) from the coagulant mixture and PAC (10%), Cr, Cd, Pb, Ni, and Hg were not detected. As for Zn, while its concentration notified in the quality standards for drinking water is 3 mg/L, only a small amount of 0.007 mg/L was detected in the coagulant mixture. Maximum amounts of over double amounts of Fe, Cu, and As were found with PAC (10%) compared to the coagulant mixture. Also, an analysis of sludge sedimentation found that the coagulant mixture showed a better performance of up to double the speed of the conventional coagulant, PAC (10%). The dry-basis lower heating value of sewage sludge produced by injecting the coagulant mixture was 3,378 kcal/kg, while that of sewage sludge generated due to PAC (10%) was 3,171 kcal/kg; although both coagulants met the requirements to be used as auxiliary fuel at thermal power plants, the coagulant mixture developed in this study could secure heating values 200 kal/kg higher than the counterpart. Therefore, utilization of the coagulant mixture for water treatment rather than PAC (10%) is expected to be more environmentally stable and effective, as it helps generating sludge with better stability against heavy metals, having a faster sludge sedimentation, and higher heating value.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 1993.12a
• /
• pp.6-9
• /
• 1993

According to changes in population, economic conditions, life-stile and eating habits, the frui ts and vegetables market wi 11 be shi fted from processed (i. e. , canned) to fresh. Undressed fresh produce, consisting of washed, disinfected and peeled fruits and vegetables that either sliced or grated, are currently increased in demand by retail and institutional market which use them as salad components or in ready-to use foods, Main attributes of minimally processed fruits and vegetables are convenience and fresh-like quality. Minimally processed Products readily deteriorate in quality, especially color and texture, as a result of endogeneous enzyme enhanced respiration and microorganisms which lead to reduced shelf Iife. According to changes in population, economic conditions, life-stile and eating habits, the frui ts and vegetables market wi 11 be shi fted from processed (i. e. , canned) to fresh. Undressed fresh produce, consisting of washed, disinfected and peeled fruits and vegetables that either sliced or grated, are currently increased in demand by retail and institutional market which use them as salad components or in ready-to use foods, Main attributes of minimally processed fruits and vegetables are convenience and fresh-like quality. Minimally processed Products readily deteriorate in quality, especially color and texture, as a result of endogeneous enzyme enhanced respiration and microorganisms which lead to reduced shelf Iife. Thus. to prevent these undesirable changes , val'ious techniques such as controlled atmosphere (CA) storage, modified atmosphere OIA) storage, including vacuum packaging have been receiving considerable attention, Although milch research has been done to find optimal conditions for whole intact frui ts and vegetables, only limi ted information is avai lable on fresh cut. and other minimally processed products. 81 iced frui ts exhibi t increas~d ethylene production and respiration compal'ed to whole f, 'uits during distribution in response to tissue damage. As a result, accelerated senescence and enzymatic browning OCCUI', Recent l'esearch on minimally processed fl'uits and vegetables has mainly focused on methods to inhibit browning, due to ban on use of sulfur dioxide, In order to retard or prevent these physiological changes, val'ious al ternatives, reducing agents. acidulants, chelating agents and inol'ganic sal ts have been evaluated for use on fresh cut fl'ui ts. Al though some agents were effective replacement for sulfur dioxide. consum$\textregistered$I'S demandless use of chemical on such products. Shel~ life of minimally processed products has been extended by inhibition of metabolic reactions associated with loss of quality and by inhibition of aerobic spoilage caused by wide variety of microorganisms. Appl ication of ~I.-\ packaging, including vacuum packaging, retards the rate of respiration, prevents growth of aerobic spoilage organisms, inhibits oxidation and color deterioration. Tissue softening is another major problem in minimally processed products because enzymes re 1 a ted to ce 11 wa 11 degrada t i on are not inactivated. Various treatments have been investigated for retardation of the softening of sliced products. Some studies have concentrated on the application of an active packaging system with ~I, l. packaging and calcium infi 1 tration as possible measures to retain firmness of processed products. In my opinion, one important step for production of minimally processed frui ts wi th favorabl e color of cut surface and firm texture is the selection of better cultivar. As the view, changing tendency of fresh color by apple cultivars and relationship between the tendency and PPO activity will be discussed in the seminar. In addition to the topic, research result on quality enhancement of fresh apple slices by heat shock treatment will be introduced.

• Journal of the Korean Geographical Society
• /
• v.29 no.1
• /
• pp.46-64
• /
• 1994

Among every civilized people salt has been recognized as an essential foodstuff to the human society without which even man's survivor is unthinkable. The cultural-anthropological meaning of salt is estimated highly as well, and in geographical perspective salt itself symbolize regional interrelationship. Playing a decisive role in freeing innermost settlement from isolation, salt aiso made a contribution to expanding human habitats. This study tries to reconstruct historica geography of 18th and 19th century surrounding traditional salt-roasting (chayeom). The Joolpo Inlet area which is located on the mid-western coast in Honem Region is selected for study area. Established on the basis of optimum physical geographical conditions such as topography, climate and vegetation, salt-making of Joolpo Inlet area was run dynamically with the sudden turn of events in the 18-19th century which was chacterized as an age of transition from medieval society to modern one. In this paper the writer attempts to clarify mainly following three points: physical conditions and socio-economic background leading to the initiation and later development of roasting of salt in Joolpo Bay; distribution of saltworks; methods of saltmaking. Main points drawn from these analyses can be summarized as follows: of iron pan and cow-drawn tools rendered labour-saving and output growth. 1, Saltworks of Joolpo Inlet area in the 18-19th century were distributed evenly over Kobu, Puan, Mujang and Heungduck counties among which Kobu's was located in Puanmyon - a sort of exclave. All saltworks belonging to above four counties were clasified as most lucrative ones in Honam Region on government archives. In particular, Gumdang saltwork which belongs to Mujang county is noteworthy in that it was first introduced by one Paekje priest in 6th century and therefore it provides a clue to examine the history of salt-roasting of Joolpo Inlet area. In light of the fact that temple or monastery economy, regardless of East and West, has been closely connected with traditional industry, the case of Gumdang is not unusual. 2. The process of saltmaking follows this order: harrowing of salt field exposed to solar heat; construction of saltern mound with saline earth; acquiring of brine by leaching saline earth; roasting of salt. Salterns (saltworks) are consisted with various salt making facilities such as roasting shed, saltern mound, salt field, salt well) salt pit or brine pit) and seawater reservoir. Among them roasting shed which is constructed chiefly with hundreds of pieces of pine tree as a frame and with straw as roof and wall is customarily considered as an unit of saltwork. And inside it is saltpan made of two kinds of materials, that is iron pan or plaster pan. The area attached to one unit of roasting shed is approximately 1 ha, and that of saltern mound is a tenth of it.

• Investigative Magnetic Resonance Imaging
• /
• v.12 no.2
• /
• pp.131-141
• /
• 2008

Purpose : To investigate the feasibility and accuracy of Proton Resonance Frequency (PRF) shift based magnetic resonance (MR) temperature mapping utilizing the self-developed center array-sequencing phase unwrapping (PU) method for non-invasive temperature monitoring. Materials and Methods : The computer simulation was done on the PU algorithm for performance evaluation before further application to MR thermometry. The MR experiments were conducted in two approaches namely PU experiment, and temperature mapping experiment based on the PU technique with all the image postprocessing implemented in MATLAB. A 1.5T MR scanner employing a knee coil with $T2^*$ GRE (Gradient Recalled Echo) pulse sequence were used throughout the experiments. Various subjects such as water phantom, orange, and agarose gel phantom were used for the assessment of the self-developed PU algorithm. The MR temperature mapping experiment was initially attempted on the agarose gel phantom only with the application of a custom-made thermoregulating water pump as the heating source. Heat was generated to the phantom via hot water circulation whilst temperature variation was observed with T-type thermocouple. The PU program was implemented on the reconstructed wrapped phase images prior to map the temperature distribution of subjects. As the temperature change is directly proportional to the phase difference map, the absolute temperature could be estimated from the summation of the computed temperature difference with the measured ambient temperature of subjects. Results : The PU technique successfully recovered and removed the phase wrapping artifacts on MR phase images with various subjects by producing a smooth and continuous phase map thus producing a more reliable temperature map. Conclusion : This work presented a rapid, and robust self-developed center array-sequencing PU algorithm feasible for the application of MR temperature mapping according to the PRF phase shift property.

• Korean Journal of Materials Research
• /
• v.6 no.7
• /
• pp.700-708
• /
• 1996

Electroless plating technique was utilized to flip chip bonding to improve surface mount characteristics. Each step of plating procedure was studied in terms pf pH, plating temperature and plating time. Al patterned 4 inch Si wafers were used as substrstes and zincate was used as an activation solution. Heat treatment was carried out for all the specimens in the temperature range from room temperature to $400^{\circ}C$ for $30^{\circ}C$ minutes in a vacuum furnace. Homogeneous distribution of Zn particles of size was obtained by the zincate treatment with pH 13 ~ 13.5, solution concentration of 15 ~ 25% at room temperature. The plating rates for both Ni-P and Au electroless plating steps increased with increasing the plating temperature and pH. The main crystallization planes of the plated Au were found to be (111) a pH 7 and (200) and (111) at pH 9 independent of the annealing temperature.

• Korean Journal of Food Science and Technology
• /
• v.12 no.3
• /
• pp.170-175
• /
• 1980

A mass production of chestnut necessiates the development of economic long-term storage method. The main objective of this study was to confirm the technical aspect of the chestnut storage method which was developed by two year project and to review the method of commercial application. The chestnut used for the experiments were separated in brine $(5.5{\sim}6.0^{\circ}\:B{\acute{a}}ume)$ into matured and unmatured lots and fumigated with $CS_2$ at a 5 $lb/27\;m^3$ level for $25{\sim}30\;hrs.$ The chestnuts were packed in wooden boxes with sawdust (50% moisture) in the ratio of 1 : 1 by volume. The boxes were stored in the cold room $(1{\pm}1^{\circ}C,\;85{\sim}95%\;RH)$ and the cellar ($0{\sim}10^{\circ}C$, controlled only by circulating night cool air). The results obtained were as follows: 1. Fully matured chestnut could be successfully preserved $8{\sim}9\;months$ at a l0% decay level in the cold room and $4{\sim}5\;months$ months in cellar. 2. Immatured chestnuts wire inferior to the matured in storage stability. At the maximum storage period, its storage life was two months shorter. 3. The heat transfer equation of piled chestnuts with sawdust can be suggested as $T_{\infty}-T_0=(T_{\infty}-T_0){\cdot}10^{-t/320}$ and j and $f_h$ values were 1 and 320 min, respectively. 4. The chestnuts in the package of storage unit had longer shelf life than naked chestnut during the retail distribution at ambient temperature.

• Korean Journal of Ecology and Environment
• /
• v.47 no.3
• /
• pp.186-193
• /
• 2014

This study aimed to analyze spatio-temporal trends of phenological characteristics in South Korea by using MODIS EVI. For the phenology analysis, we had applied double logistic function to MODIS time-series data. Our results showed that starting date of phenology seems to have a tendency along with latitudinal trends. Starting date of phenology of Jeju Island and Mt. Sobeak went back for 0.38, 0.174 days per year, respectively whereas, Mt. Jiri and Mt. Seolak went forward for 0.32 days, 0.239 days and 0.119 days, respectively. Our results exhibited the fluctuation of plant phonological season rather than the change of phonological timing and season. Starting date of plant phenology by spatial distribution revealed tendency that starting date of mountain area was late, and basin and south foot of mountain was fast. In urban ares such as Seoul metropolitan, Masan, Changwon, Milyang, Daegu and Jeju, the phonological starting date went forward quickly. Pheonoligcal attributes such as starting date and leaf fall in urban areas likely being affected from heat island effect and related warming. Our study expressed that local and regional monitoring on phonological events and changes in Korea would be possible through MODIS data.

• Nuclear Engineering and Technology
• /
• v.39 no.5
• /
• pp.603-616
• /
• 2007

Roy Huddle, having invented the coated particle in Harwell 1957, stated in the early 1970s that we know now everything about particles and coatings and should be going over to deal with other problems. This was on the occasion of the Dragon fuel performance information meeting London 1973: How wrong a genius be! It took until 1978 that really good particles were made in Germany, then during the Japanese HTTR production in the 1990s and finally the Chinese 2000-2001 campaign for HTR-10. Here, we present a review of history and present status. Today, good fuel is measured by different standards from the seventies: where $9*10^{-4}$ initial free heavy metal fraction was typical for early AVR carbide fuel and $3*10^{-4}$ initial free heavy metal fraction was acceptable for oxide fuel in THTR, we insist on values more than an order of magnitude below this value today. Half a percent of particle failure at the end-of-irradiation, another ancient standard, is not even acceptable today, even for the most severe accidents. While legislation and licensing has not changed, one of the reasons we insist on these improvements is the preference for passive systems rather than active controls of earlier times. After renewed HTGR interest, we are reporting about the start of new or reactivated coated particle work in several parts of the world, considering the aspects of designs/ traditional and new materials, manufacturing technologies/ quality control quality assurance, irradiation and accident performance, modeling and performance predictions, and fuel cycle aspects and spent fuel treatment. In very general terms, the coated particle should be strong, reliable, retentive, and affordable. These properties have to be quantified and will be eventually optimized for a specific application system. Results obtained so far indicate that the same particle can be used for steam cycle applications with $700-750^{\circ}C$ helium coolant gas exit, for gas turbine applications at $850-900^{\circ}C$ and for process heat/hydrogen generation applications with $950^{\circ}C$ outlet temperatures. There is a clear set of standards for modem high quality fuel in terms of low levels of heavy metal contamination, manufacture-induced particle defects during fuel body and fuel element making, irradiation/accident induced particle failures and limits on fission product release from intact particles. While gas-cooled reactor design is still open-ended with blocks for the prismatic and spherical fuel elements for the pebble-bed design, there is near worldwide agreement on high quality fuel: a $500{\mu}m$ diameter $UO_2$ kernel of 10% enrichment is surrounded by a $100{\mu}m$ thick sacrificial buffer layer to be followed by a dense inner pyrocarbon layer, a high quality silicon carbide layer of $35{\mu}m$ thickness and theoretical density and another outer pyrocarbon layer. Good performance has been demonstrated both under operational and under accident conditions, i.e. to 10% FIMA and maximum $1600^{\circ}C$ afterwards. And it is the wide-ranging demonstration experience that makes this particle superior. Recommendations are made for further work: 1. Generation of data for presently manufactured materials, e.g. SiC strength and strength distribution, PyC creep and shrinkage and many more material data sets. 2. Renewed start of irradiation and accident testing of modem coated particle fuel. 3. Analysis of existing and newly created data with a view to demonstrate satisfactory performance at burnups beyond 10% FIMA and complete fission product retention even in accidents that go beyond $1600^{\circ}C$ for a short period of time. This work should proceed at both national and international level.