• 에너지공학
• /
• 제17권2호
• /
• pp.107-115
• /
• 2008

신에너지원으로 주목받고 있는 중질 잔사유를 기존 중유화력의 대체 연료로 사용하는 경우에 대하여 상용 해석코드로 플랜트의 에너지 및 물질 수지, 플랜트의 성능을 분석하였다. 국내 A 중유 화력발전소에 대한 플랜트 성능분석 모델을 구축하였으며 플랜트의 성능 및 효율 등에 대한 시뮬레이션 결과를 설계 및 실제 운전 데이터와 비교하여 그 건전성을 확인하였다. 중질 잔사유 적용에 대한 시뮬레이션 결과 출력은 315 MW로서 중유 적용시의 300 MW 보다 높게 나타났으며 플랜트 효율은 약간 감소함을 알 수 있었다. 외기온도 및 냉각수 온도, 배가스 순환량, 출력에 따른 열소비율의 민감도 분석으로부터 중질 잔사유 연소시의 최적 운전을 위한 기본 자료를 얻을 수 있었다.

• 자원리싸이클링
• /
• 제9권3호
• /
• pp.13-21
• /
• 2000

본 연구는 폐용제를 가열, 증발 및 음축과정을 거쳐 용제를 회수하는 시스템의 열교환기 해석에 관한 것으로, 고온 열매체유로 가열되는 이중관형 열교환기를 사용하여 용제 증발과정의 열전달 특성을 분석하고 용제유량과 가열온도에 따라 물, 벤젠 및 알칼벤젠의 증발을 위해 요구되는 전열면적을 분석하였다. 폐용제 회수장치는 용제 공급펌프 이중관형 열교환기, 진공 스프레이 챕버 및 응축기동으로 구성되며, 이중관형 열교환기는 용제액을 열적 포화온도를 가열시키는 구간과 포화된 용제액을 증발시키는 구간으로 구성된다. 관 내 용제의 증발을 위한 전열면적을 열평형 모델링에 의해 예측하였고, 이중관형 열교화기의 관 내 온도분포 측정을 통해 이론값과 비교 분석하였다. 용제유량 0.1~0.51l/mm 및 가열온도 130~$260^{\circ}C$의 범위에서 용제유향 증가 및 가열온도 감속에 따라 단위전열면적당 열전달양이 감소하기 때문에 용제 증발을 위한 전열면적은 증가하였다. 관 내 용제 증발을 위한 전열면적의 이론적 분석결과는 측정값과 일치하였으며, 이중관형 열교환기를 사용한 폐용제의 증발과정을 통해 용제를 회수하는 기술에 적용이 가능하다.

• 분석과학
• /
• 제31권1호
• /
• pp.31-38
• /
• 2018

기존 폐기물 저위발열량 측정 분석 방법은 소량의 시료에 대한 발열량계 측정 및 원소분석 결과로 저위발열량 환산식을 적용하여 산정하도록 규정하고 있다. 즉, 기존 저위발열량 산정방법은 폐기물의 불균질성, 지역적 특성, 계절적 특성 등을 충분히 반영하지 못하여 대표성과 객관성 측면에서의 한계를 나타내고 있다. 이러한 문제로 환경부 고시(제2015-251호)에서는 저위발열량의 대표성 확보를 위하여 산정방법을 개정하였으며, "KS B 6205 육상용 보일러의 열정산방식"을 바탕으로 열정산방법을 적용한 사업장폐기물 소각시설에서의 저위발열량 산정방법을 제시하고 있다. 본 연구에서는 현재 운영 중인 사업장폐기물 소각시설을 대상으로 열정산법에 따라 시설별 투입 폐기물의 저위발열량을 분석 평가하였다. 사업장폐기물 소각시설 7 개소 (10 개호기)에 대한 저위발열량 평가 결과 평균 약 3,404.7 kcal/kg로 산정되었으며, 세부 산정 인자에는 실제 시설 운영 데이터를 수집 종합 하여 적용하였다. 본 연구에서 적용한 개정된 저위발열량 산정 방법은 불균질한 성상의 폐기물 특성을 반영할 수 있는 방법으로, 기존 폐기물 발열량 산정방법과 비교하여 보다 객관성을 확보한 방법인 것으로 판단된다. 본 연구의 결과는 추후 세부적인 저위발열량 산정방법 개선 및 산정인자 도출 등을 위한 기초자료로 활용 될 수 있을 것으로 판단된다.

• Journal of Dairy Science and Biotechnology
• /
• 제35권4호
• /
• pp.270-285
• /
• 2017

Among milk proteins, caseins are not subjected to chemical changes during heat treatment of milk; however, whey proteins are partially denatured following heat treatment. The degree of whey protein denaturation by heat treatment is decreased in the order of high temperature short time (HTST) > low temperature long time (LTLT) > direct-ultra-high temperature (UHT) > indirect-UHT. As a result of heat treatment, several changes, including variations in milk nitrogen, interactions between beta-lactoglobulin and k-casein, variations in calcium sulfate and casein micelle size, and delay of milk coagulation by chymosin action, were observed. Lysine, an important essential amino acid found in milk, was partially inactivated during heat treatment. Therefore, the available amount of lysine decreased slightly (1~4% decrease) after heat treatment, However, the influence of heat treatment on the nutritional value of milk was negligible. Nutritional value and nitrogen balance did not differ significantly between UHT and LTLT in milk. In conclusion, our results showed that heat treatment of milk did not alter protein quality. Whey proteins denatured to a limited extent during the heat treatment process, and the nutritional value and protein quality were unaffected by heat treatment.

• 설비공학논문집
• /
• 제3권2호
• /
• pp.114-122
• /
• 1991

A thermal analysis method taking into account energy balance in each elements of heat exchanger was introduced. This method has a merit in predicting the temperature field over the heat exchanger in detail. To verify this method, the results were compared with the published ones. The thermal analysis of the radiator in vehicles was also conducted and the results were compared with experimental ones. It is concluded that this method can be used in thermal analysis with relatively small error. When the velocity profile of inlet air is not uniform, the outlet temperature of cooling water is higher than that of uniform velocity profile.

• 한국환경과학회지
• /
• 제8권2호
• /
• pp.151-154
• /
• 1999

To verify the accuracy of the numerical experiment of Part I, measurements at the matured rice canopy located around Junam reservoir were performed at August 14, 1995. According to the measured data, the foliage temperature recorded the highest value, and the ground temperature was the lowest around noon, and these results coincided with those of the numerical experiment using the combined model of Part I. From the estimation using measured data, the maximum value of the latent heat flux was 380$Wm^2$, the highest value among energy balance terms, and the energy redistribution ratio of the latent heat flux was averaged as 0.5, the highest values among redistribution ratios. These results are the same as those of the numerical experiment in tendency, but they reveals a little lower in the absolute values than those from the numerical experiment.

• 대한기계학회논문집B
• /
• 제23권9호
• /
• pp.1201-1212
• /
• 1999

A numerical analysis is performed to predict the thermal response and ablation rate for charring or non-charring material which is designed to be used as thermal protection system (TPS). The numerical program composed of in-depth energy balance equation and the aerotherm chemical equilibrium (ACE) program. The ACE program calculates various thermochemical state from ablation products. The developed numerical program is verified by comparing the reported results from literature. The sensitivity tests for input parameters are performed. The thermal behavior of ablating material is mainly affected by density of ablating material, convective heat transfer coefficient and recovery enthalpy of flow field.

• Architectural research
• /
• 제14권1호
• /
• pp.11-18
• /
• 2012

College of Architecture, Georgia Institute of Technology, Atlanta, GA, US Abstract The intermittent heating and cooling energy need calculation of the ISO 13790 monthly method was examined. The current ISO 13790 method applies a reduction factor to the continuous heating and cooling need calculation result to derive the intermittent heating and cooling for each month. This paper proposes a method for the intermittent energy need calculation based on the internal mean temperature calculation. The internal temperature calculation procedure was introduced considering the heat-balance taking into account of heat gain, heat loss, and thermal inertia for reduced heating and cooling period. Then, the calculated internal mean temperature was used for the intermittent heating and cooling energy need calculation. The calculation results from the proposed method were compared to the current ISO 13790 method and validated with a dynamic simulation using EnergyPlus. The study indicates that the intermittent heating and cooling energy need calculation method using the proposed model improves transparency of the current ISO 13790 method and draws more rational outcomes in the monthly heating and cooling energy need calculation.

• 한국태양에너지학회 논문집
• /
• 제25권3호
• /
• pp.27-35
• /
• 2005

In this paper, a thermodynamic analysis was performed to provide design data for a double-effect absorption heating system with water-LiBr-LiSCN mixture which utilizes solar energy as evaporator heat source. In addition, a comparative study of the water-LiBr-LiSCN mixture against the water-LiBr pair was conducted by a computer simulation. The computer simulation is based on mass, material and heat balance equations for each part of the system. Coefficients of performance and flow ratios for effects of different operating temperatures are investigated. It is found that the heating COP is higher for the water-LiBr-LiSCN mixture than for the water-LiBr pair, and FR is lower for the former.

• Tribology and Lubricants
• /
• 제12권3호
• /
• pp.79-84
• /
• 1996

One of the greatest dangers in mechanical face seals is the formation of heat checking and thermal stress cracks on the sliding surfaces. These thermal distortions due to non-uniform heating lead to increase the leakage of the sealed fluids and wear, and with balance of the seal can cause the seal faces to part. In this study heat checking and thermal stress cracks are investigated experimentally. These thermal distortions are explained using the thermal models of the conatct geometries between the seal ring and the seal seat. To overcome these thermal problems, the thermohydrodynamic seal is presented. The newly developed mechanical seal may substantially reduce the friction torque, frictional heating which causes heat checking and thermal stress cracks, and wear.