• Korean Chemical Engineering Research
• /
• v.55 no.4
• /
• pp.530-534
• /
• 2017

Chitosan is a promising flocculant for microalgae harvesting, but its scale-up application is not economically supported yet. Low solubility of chitosan in microalgae suspension demands high dosage (as a flocculant) to destabilize the cells, and thus, increases the cost of microalgae harvesting. This study identifies efficient solvents for the chitosan, and optimizes the concentration of solvents and chitosan dose to improve the harvesting efficiency. Chitosan was dissolved in different acids, and subsequently used as a flocculant. The flocculant efficacy was measured in terms of harvesting efficiency and reduction in chemical oxygen demand (COD) of the microalgae suspension. It was found that chitosan dissolved in 0.05 M HCl showed the highest harvesting efficiency ($89{\pm}0.87%$) at only 30 mg/L of dosage. In comparison, 270 mg/L of $FeCl_3{\cdot}6H_2O$ was required to attain $86{\pm}0.083%$ of the harvesting efficiency. $H_2SO_4$ dissolved chitosan required high flocculant dose (150 mg/L) and resulted in relatively low harvesting efficiency ($77{\pm}0.11%$). It was concluded that the efficacy of chitosan is solvent dependent, and the selection of proper solvent can decrease the dosage requirement for microalgae harvesting.

• Journal of Biosystems Engineering
• /
• v.27 no.6
• /
• pp.513-520
• /
• 2002

A 5-row walking garlic harvester with pulling mechanism was developed in the study, based upon a kinematical analysis and related preliminary field tests on the conventional garlic harvesting method. The harvesting efficiency of the developed harvester was more than 98% in the garlic field irrigated before harvesting, 80-85% in the field without irrigation. The harvesting performance of the harvester was 660∼825㎡/hr at the forward speed of harvester of 0.3m/s in the irrigated field before garlic harvesting. For proper garlic drying and collection, the harvester discharged the harvested garlic on the ground uniformly at the angles of 135。∼150。 to its forward direction with the garlic bulb's placing toward the harvester. In the field tests, it was recommended that the forward speed of the harvester be approximately less than 0.2m/s, and that the spacing of planting garlic seeds should be standardized in the future fur increasing its harvesting efficiency.

• Journal of Electrochemical Science and Technology
• /
• v.1 no.2
• /
• pp.69-74
• /
• 2010

Methodologies to improve photovoltaic performance of dye-sensitized solar cell (DSSC) are reviewed. DSSC is usually composed of a dye-adsorbed $TiO_2$ photoanode, a tri-iodide/iodide redox electrolyte and a Pt counter electrode. Among the photovoltaic parameters of short-circuit photocurrent density, open-circuit voltage and fill factor, short-circuit photocurrent density is the collective measure of light harvesting, charge separation and charge collection efficiencies. Internal quantum efficiency is known to reach almost 100%, which indicates that charge separation occurs without loss by recombination. Thus, light harvesting efficiency plays an important role in improvement of photocurrent. In this paper, technologies to improve light harvesting efficiency, including surface area improvement by nano-dispersion, size-dependent light scattering efficiency, bi-functional nano material, panchromatic absorption by selective positioning of three different dyes and transparent conductive oxide (TCO)-less DSSC, are introduced.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.925-926
• /
• 2014

The purpose of this study is intended to improve the efficiency of energy harvesting through the optimal design of the PZT system and the electrical system. To improve the efficiency of energy harvesting, it is necessary to increase the output voltage generated from the PZT. In this study, first the mounting position and shape of the PZT which is attached to the cantilever were optimized. Second electric circuit was optimized by using a series connection of a circuit and the electrical resonance frequency. As a result, we improve the output voltage about 5V.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.60 no.1
• /
• pp.31-36
• /
• 2018

A rainwater harvesting device was developed for runoff flow harvesting in a small stream or channel and its performance was evaluated in small fields. The rainwater harvesting device has slits on its side of cylindrical volume in 15 cm diameter and 70 cm length, which is designed to increase its water flow harvesting capacity. The maximum collectable water quantity was about 0.0022 ton/sec (130 L/min). Rainwater harvesting device were installed in two locations (P1, P2). P1 is a point for rainfall runoff flow harvesting. P2 is a point for ordinary flow harvesting. During this study, total rainfall depth was 334.5 mm. Runoff of 1,722 ton and 7,984 ton occurred in P1 and P2, and 273 ton and 125 ton were collected by this rainwater harvesting device. Harvesting efficiency was calculated as 15.85 % and 1.57 % in P1 and P2. Clogging of screen filter media in the cylinder due to soil and suspended solids has lowered the harvesting efficiency. However, it was possible to harvest 30 ton/month of rainwater harvesting and it is expected that it will help to solve short-term water shortage.

• Journal of Drive and Control
• /
• v.20 no.3
• /
• pp.35-41
• /
• 2023

Radish and Chinese cabbage are the most produced and consumed vegetables in Korea. The mechanization of harvesting operations is necessary to minimize the need for manual labor. This study to develop and evaluate the performance of a multi-purpose driving platform that can apply modular Radish and Chinese cabbage harvesting devices. The multi-purpose driving platform consisted of driving, device control, engine, hydraulic, harvesting, conveying, and loading part. Radish and Chinese cabbage harvesting conducted using the multi-purpose driving platform each harvesting module. The performance of the multi-purpose driving platform was evaluated the field efficiency and loss rate. The total Radish harvesting operation time 34.3 min., including 28.8 min., of harvesting time, 1.9 min., of turning time, and 3.6 min., of replacement time of bulk bag. During Radish harvesting, the field efficiency and average loss rate of the multi-purpose driving platform were 2.0 hr/10a and 3.1 %. Chinese cabbage harvesting operation 49.3 min., including 26.6 min., of harvesting time, 4.6 min., of turning time, and 18.1 min., of replacement time of bulk bag. During Chinese cabbage harvesting, the field efficiency and average loss rate of the multi-purpose driving platform 2.1 hr/10a and 0.1 %. Performance evaluation of the multi-purpose driving platform that harvesting work was possible by installing Radish and Chinese cabbage harvest modules. Performance analysis through harvest performance evaluation in various Radish and Chinese cabbage cultivation environments is necessary.

• Journal of Semiconductor Engineering
• /
• v.1 no.1
• /
• pp.13-30
• /
• 2020

Radio frequency (RF) energy harvesting technology have become a reliable and promising alternative to extend the lifetime of power-constrained wireless networks by eliminating the need for batteries. This emerging technology enables the low-power wireless devices to be self-sustaining and eco-friendly by scavenging RF energy from ambient environment or dedicated energy sources. These attributes make RF energy harvesting technology feasible and attractive to an extended range of applications. However, despite being the most reliable energy harvesting technology, there are several challenges (especially power conversion efficiency, output DC voltage and sensitivity) poised for the implementation of RF energy harvesting systems. In this article, a detailed literature on RF energy harvesting technology has been surveyed to provide guidance for RF energy harvesters design. Since signal strength of the received RF power is limited and weak, high efficiency state-of-the-art RF energy harvesters are required to design for providing sufficient DC supply voltage to wireless networks. Therefore, various designs and their trade-offs with comprehensive analysis for RF energy harvesters have been discussed. This paper can serve as a good reference for the researchers to catch new research topics in the field of RF energy harvesting.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.67 no.3
• /
• pp.137-142
• /
• 2018

Energy harvesting technology is drawing attention as a means of collecting various eco-friendly energy and accumulating residual energy. Recently, differential power processing (DPP) is being developed as part of energy harvesting. This is being studied as a solution to the loss of power generation between power modules and the problems caused by module small losses depending on the size of power production. In this paper, we propose the necessity of the DPP by comparing and analyzing energy harvesting related module integration system and power supply efficiency of DPP. The power efficiency of the converter and the power difference between the wind power and the photovoltaic power supply have been changed to demonstrate the effectiveness of the proposed system.

• Journal of Korean Society on Water Environment
• /
• v.31 no.3
• /
• pp.328-333
• /
• 2015

In this study, Mg-Sericite was used as a flocculant to harvest freshwater microalgae, Chlorella. vulgaris. Mg-Sericite separated successfully >95% of the C. vulgaris at the following optimal parameters: Mg/Si mol ratio 1.25 to 1.50, mixing time of 20 min and settling time of 20 min. The harvesting efficiency was pH dependent. The highest harvesting efficiency ($99{\pm}0.3%$) was obtained at Mg/Si mol ratio 1.5 and pH 9 to 11. These results indicated that a biopolymer, Mg-Sericite, can be a promising flocculant due to its high efficiency, low dose requirements, short mixing and settling times. This harvesting method is helpful to lower the production cost of algae for biodiesel.

• Journal of the Korean Society of Visualization
• /
• v.19 no.3
• /
• pp.31-38
• /
• 2021

The energy harvesting system using an inverted flag is analyzed by using an immersed boundary method to consider the fluid and solid interaction. The inverted flag flutters at a lower critical velocity than a conventional flag. A fluttering motion is classified into straight, symmetric, asymmetric, biased, and over flapping modes. The optimal energy harvesting efficiency is observed at the biased flapping mode. Using the three different machine learning algorithms, i.e., artificial neural network, random forest, support vector regression, the energy harvesting efficiency is predicted by taking bending rigidity, inclination angle, and flapping frequency as input variables. The R² value of the artificial neural network and random forest algorithms is observed to be more than 0.9.