• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.4 no.2
• /
• pp.93-100
• /
• 1999

Analyzing the tide data taken at Kunsan inner and Outer ports, non-tidal and mean sea level and harmonic constants of major constituents are investigated to examine the effects of the dyke gate operation on the sea level change in Keum River estuary. Non-tidal and annual mean sea levels decrease at Kunsan Inner and Outer ports after the dyke gate operation, especially showing an abrupt drop of non-tidal sea level at Kunsan Inner port. This non-tidal sea level drop results in the mean sea level gradient change between the inner and outer port, which can be mainly explained in terms of the decrease of river discharge from the dyke. Amplitudes of the $M_2$ and $S_2$ tides at the Inner port increase after the dyke gate operation, showing an abrupt jump, and phases of both tides slightly decrease. Amplitude and phase of the $K_1$ and $O_1$ tides show slight changes after the dyke gate operation. This significant change of semi diurnal tide amplitude is believed as a result of superposition of incident tidal wave and reflected tidal wave from the dyke.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.8 s.99
• /
• pp.815-824
• /
• 2005

In this paper, we proposed a new DGS(Defected Ground Structure) Doherty amplifier for IMT-2000 band. Originally, active load-pull analysis of a Doherty amplifier assumes ideal harmonic termination condition. However, there have been no papers considering this ideal harmonic termination condition. We obtained excellent improvements of efficiency, gain, maximum output power as well as superior size reduction of a Doherly amplifier by satisfying the overlooked assumption of ideal harmonic termination through the adaptation of DGS at the output transmission line of carrier and peaking amplifier that is essential for Doherty operation. The amount of both the 2nd and the 3rd harmonic rejection of the proposed DGS Doherty amplifier over the conventional one are 44.92 dB and over 23.77 dB, respectively. The acquired improvement in Pl dB, gain, drain efficiency, and ACPR to WCDMA 1FA signal were 0.42 dB, 0.33 dB, $6.4\%$ and 5.4 dBc, respectively. Moreover, electrical length of $90{\circ}$ is reduced at each of the DGS carrier amplifier path and DGS peaking amplifier path, therefore the whole amplifier circuit size is considerably reduced.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.1B
• /
• pp.101-110
• /
• 2011

With the deployment of broadband networking technology, many clients are enabled to receive various Video on Demand (VoD) services. To support many clients, the network should be designed by considering the following factors: viewer's waiting time, buffer requirement at each client, number of channel required for video delivery, and video segmentation complexity. Among the currently available VoD service approaches, the Polyharmonic and Staircase broadcasting approaches show best performance with respect to each viewer's waiting time and buffer requirement, respectively. However, these approaches have the problem of dividing a video into too many segments, which causes very many channels to be managed and used at a time. To overcome this problem, we propose Polyharmonic-Staircase-Staggered (PSS) broadcasting approach that uses the Polyharmonic and Staircase approaches for the head part transmission and the Staggered approach for the tail part transmission. It is simple and bandwidth efficient. The numerical results demonstrate that our approach shows viewer's waiting time is comparable to that in the Harmonic approach with a slight increase in the bandwidth requirement, and saves the buffer requirement by about 60\% compared to the Harmonic broadcasting approach by simply adjusting the video partitioning coefficient factor. More importantly, our approach shows the best performance in terms of the number of segments and the number of channels managed and used simultaneously, which is a critical factor in real operation of VoD services. Lastly, we present how to configure the system adaptively according to the video partitioning coefficient.

• Journal of the Society of Disaster Information
• /
• v.17 no.1
• /
• pp.184-193
• /
• 2021

Purpose: In this study, since the operation principle of the CCFL Exit light is the same as that of general lighting equipment, the characteristics of the CCFL Exit light were analyzed by deriving test items that can affect the characteristics of the light source from the KS standard, which is the standard for lamp ballast performance certification of general lighting equipment. Method: The samples used in the experiment were performed on products of two manufacturers for each size, such as large, medium, and small, and the test items were power factor, crest factor, and current harmonic distortion. Result: As a result of the experiment, the power factor showed a value between 0.4 and 0.6 in all samples, which was smaller than the 0.9 value set by KS. The crest factor ranged from 3.6 to 3.7 for large, 4.4 to 4.7 for medium, and 3.5 to 3.7 for small. It showed a value more than two times higher than the KS standard of 1.7. Current total harmonic distortion ranged from 81% to 110%, and considering that the KS standard was less than 20%, it could be confirmed that all samples had a value significantly exceeding the KS standard. Conclusion: The crest factor and current total harmonic distortion may affect the temperature rise of the light source and the burnout of the device. When developing an exit light, if this item is developed within the scope of the KS standard, the quality improvement and maintenance of the exit light will be greatly improved.

• Journal of electromagnetic engineering and science
• /
• v.14 no.1
• /
• pp.1-8
• /
• 2014

A differential-cascode CMOS power amplifier (PA) with a supply modulator for envelope tracking (ET) has been implemented by 0.18 ${\mu}m$ RF CMOS technology. The loss at the output is minimized by implementing the output transformer on a FR-4 printed circuit board (PCB). The CMOS PA utilizes the $2^{nd}$ harmonic short at the input to enhance the linearity. The measurement was done by the 10MHz bandwidth 16QAM 6.88 dB peak-to-average power ratio long-term evolution (LTE) signal at 1.85 GHz. The ET operation of the CMOS PA with the supply modulator enhances the power-added efficiency (PAE) by 2.5, to 10% over the stand-alone CMOS PA for the LTE signal. The ET PA achieves a PAE of 36.5% and an $ACLR_{E-UTRA}$ of -32.7 dBc at an average output power of 27 dBm.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.2152_2153
• /
• 2009

In this study, the dynamic characteristic of a contact wire and pantograph suppling electrical power to high-speed trains are investigated from an electrical response point of view. To analysis power line disturbance by induced contact loss phenomenon for high speed operation, a hardware Simulator which considered contact loss between contact wire and the pantograph as well as contact wire deviation is developed. It is confirmed that a contact wire and pantograph model are necessary for studying the dynamic behavior of the pantograph system. One of the most important needs accompanied by increasing the speed of high-speed train is reduced that an arc phenomenon by loss of contact brings out EMI. In case of a high-speed train using electrical power, as comparison with diesel rolling stock, PLD(Power Line Disturbance) such as harmonic, transient voltage and current, EMI, dummy signal injection etc usually occurs. Throughout experiment, it is verified that an arc phenomenon is brought out for simulator operation and consequently conducted noise is flowed in electric circuit by power line disturbance.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.4
• /
• pp.427-431
• /
• 2009

In this study, the dynamic characteristic of a contact wire and pantograph suppling electrical power to high-speed trains are investigated from an electrical response point of view. To analysis power line disturbance by induced contact loss phenomenon for high speed operation, a hardware Simulator which considered contact loss between contact wire and the pantograph as well as contact wire deviation is developed. It is confirmed that a contact wire and pantograph model are necessary for studying the dynamic behavior of the pantograph system. One of the most important needs accompanied by increasing the speed of high-speed train is reduced that an arc phenomenon by loss of contact brings out EMI. In case of a high-speed train using electrical power, as comparison with diesel rolling stock, PLD(Power Line Disturbance) such as harmonic, transient voltage and current, EMI(Electromagnetic Interference), dummy signal injection etc usually occurs. Throughout experiment, it is verified that an arc phenomenon is brought out for simulator operation and consequently conducted noise is flowed in electric circuit by power line disturbance.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.3
• /
• pp.499-505
• /
• 2020

Capacitor-run single-phase induction motor is cheaper than motors that use permanent magnets and is widely used in home appliances and industries based on relatively high durability and productivity. It can also be operated by line. However speed cannot be controlled because the line frequency is free. In this paper we dealt pole change method one of the method controlling speed of capacitor-run single-phase induction motor. The conventional pole change method is difficult to improve the power and efficiency of the motor because the composition of the pole change device is complex and do not have enough area of the windings because of windings not used according to the driving conditions. In this paper, we proposed the pole change method that is used main windings and auxiliary windings at 4 poles operation and used auxiliary windings as compensation windings at 2 poles operation. The proposed method was verified through finite element analysis.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.5
• /
• pp.410-415
• /
• 2004

To ensure a safe operation of the prototype KGT-74 kW small gas turbine, vibrational reliabilities of the compressor 1st, 2nd, and 3rd stages and turbine blades have been estimated and reviewed. FE analyses have been carried out to obtain the natural vibration characteristics of the blades, and impact modal testings have been performed on every each one of the blades to measure their 1st natural frequencies. Then, the Campbell diagram analyses have been carried out to judge the safety of the blades from resonant failures up to 6k harmonics. Results show that the compressor 1st stage blade is exposed to a potential resonant failure with 3k harmonic around a rated speed of 30,000 rpm but that the other compressor 2nd and 3rd stages and turbine blades are safe from resonant failures. Finally, 27,900 rpm is selected as the safe operation limit for the KGT-74 ㎾ gas turbine relative to the blade vibrations.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.12
• /
• pp.1640-1648
• /
• 2014

This paper proposes a switching frequency reduction method for MMC (Modular Multilevel Converter) utilizing redundancy operation of sub-module, which can offer reduction of voltage harmonics and switching loss. The feasibility of proposed method was verified through computer simulations with PSCAD/EMTDC software. Based on simulation analysis, a hardware scaled-model of 10kVA, DC-1000V MMC was designed and manufactured in the lab. Various experiments were conducted to verify the feasibility of proposed method in the actual hardware system. The hardware scaled-model can be effectively utilized for analyzing the performance of MMC according to the modulation scheme and redundancy operation.