• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.747-749
• /
• 2000

This study deals with the characteristic analysis of slotless PMLSM based on the analytical method. Slotless PMLSM produces the thrust ripples due to the harmonic component of back-EMF. Therefore, this paper presents the thrust ripple minimization technique, by modifying the pole ratio and the coil width. The results of the proposed mehtod are compared the ones of FEM.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.2
• /
• pp.53-59
• /
• 2005

In this paper, optimum shape design of permanent magnet in slotted type Permanent Magnet Linear Synchronous Motor(PMLSM) is progressed for minimization of detent force owing to structure of slot-teeth and thrust ripple by harmonic magnetic flux of permanent magnet. In order to reduce remodeling time as changing design parameter for Permanent Magnet shape optimization, the moving model node technique was applied. The characteristics of thrust and detent force computed by finite element analysis are acquired equal effect both skewed basic model and optimum model which is optimization of permanent magnet shape. In addition to, thrust per unit volume is improved 4.l2[%] in optimum model.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.7
• /
• pp.323-328
• /
• 2005

This paper is proposed maximum thrust design of slotted permanent magnet linear synchronous motor(PMLSM) using surface harmonic method(SHM) considering slot effect. The genetic a1gorithm is used for optimization. The functional are selected the maximum thrust and the minimum detent force. This time. design parameters are set as permanent magnet(PM) width. PM height and slot width. Thrust is increased from 272[N] to 295[N] and detent force is decreased from 5[N] to 2.43[N] greatly in optimum design. Therefore, thrust ripple isn't generating almost. Also, the results of 2D EMC considering slot-effect are compared with ones of experimental and finite element analysis..

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.1
• /
• pp.24-29
• /
• 2004

A new low cost hybrid active filter for thyristor-controlled rectifier load is presented to overcome the high cost problem of the active or the other hybrid active filters. The proposed hybrid active filter which consists of tuned (5th and 7th harmonics) LC passive filters, power factor improvement(PFI) capacitor bank, and active filter compensates power factor as well as harmonic currents. Since most of harmonic currents are filtered by the passive filter and most of reactive power is compensated by the PFI capacitor bank, the power rating of active filter can be minimized, resulting in cost minimization of the proposed hybrid active filter. A 300kVA hybrid active filter system is implemented and tested using 1MVA thyristor rectifier load to verify the operation and performance.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.34 no.9
• /
• pp.368-375
• /
• 1985

This paper describes the OPTIMAL PWM strategy to reduce harmonic losses for a variaboe-speed drive of an induction motor. This OPTIMAL theory is the strategy which can reduce motor losses by defining harmonic losses as a performance index and achieving it's minimization. This PWM strategy is compared with the conventional NATURAL PWM technique by a numerical method, and verified the validity of numerical method by a result of implementing in a practical 1 Hp-3 Phase induction motor drive system. Also, we could achieve a maximum efficiency to drive an induction motor by selecting appropriately one alternative between OPTIMAL and NATURAL PWM techniques, and employing it in a full driving range.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.268-269
• /
• 2017

This paper presents an improved current control strategy for a three-phase grid-connected inverter under distorted grid conditions. Distorted grid condition is undesirable due to negative effects such as power losses and heating problem in electrical equipments. To enhance the power quality of distributed generation systems under such a condition, a modulated finite control set - model predictive control (MFCS-MPC) scheme will be proposed, in which the optimal switching signals of inverter are chosen by online basis using the principle of current error minimization. In addition, the moving average filter (MAF) is used to improve the phase-lock loop in order to obtain the harmonic-free reference currents on the stationary frame. The usefulness of the proposed MFCS-MPC method is proved by the comparative simulation results under different operating conditions.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.273-274
• /
• 2012

This paper investigates control algorithms for a doubly fed induction generator(DFIG) with a back-to-back three-level neutral-point clamped voltage source converter in medium voltage wind power system under unbalanced grid conditions. Two different control algorithms to compensate for unbalanced conditions are proposed. Evaluation factors of control algorithm are fault ride-through(FRT) capability, efficiency, harmonic distortions and torque pulsation. Zero regulated negative sequence stator current control algorithm has the most effective performance concerning FRT capability and efficiency. Ripple-free control algorithm nullifies oscillation component of active power and reactive power. Ripple-free control algorithm shows the least harmonic distortions and torque pulsation. Combination of zero regulated negative sequence stator current and ripple-free control algorithm control algorithm depending on the operating requirements and depth of grid unbalance presents the most optimized performance factors under the generalized unbalanced operating conditions leading to high performance DFIG wind turbine system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.11
• /
• pp.943-950
• /
• 2013

This paper discusses a harmonic response estimation method on the L$\acute{e}$vy plate with two opposite edges simply supported and the other two edges having free boundary conditions. Since the equation of motion of the plate is not self-adjoint, the modes are not orthogonal to each other on the domain. Noting that the L$\acute{e}$vy plate can be expressed using one term sinusoidal function that is orthogonal to other sinusoidal functions, this paper suggested the calculation method that is equivalent to finding a least square error minimization solution of the finite number of algebraic equations. Example problems subjected to a distributed area loading and a distributed line loading are defined and their solutions are provided. The solutions are compared to those of the commercial code, ANSYS. According to the verification results, it is expected that the suggested method will be useful to predict the forced response on the L$\acute{e}$vy plate with the distributed area or line loading conditions.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.15 no.11
• /
• pp.886-897
• /
• 1990

This paper is proposed new optimal PWM scheme is based on a defined linear relationship between the successive pulsewidths of the PWM pattern. The calculation of the pulsewidths in the new PWM scheme is caried out without referring to the equations of CW and MW. With this scheme the PWM pattern for microprocessor controlled inverters can be composed easily by obtaining the optimal increment in sucessive pulsiwidths of the pattern. Furthmore, the harmonic level at the output of PWM inverter are always very low because this PWM pattern is selected on the basis of minimum THD. Theis scheme is applied to 1(Hp), three phase induction motor, and compared with conventional regular PWM scheme. The results of calculations and experiments show that new optimal PWM scheme could provide an effective generalized approach for minimization of harmonics in the VSI-PWM inverter.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.2C no.6
• /
• pp.309-313
• /
• 2002

In this paper, we have studied minimization of the kerf-width and surface burning, which occurred after the conventional singulation process of the multi-layer BGA board with copper, polyethylene and epoxy glass fiber. The high thermal energy of a pulsed Nd:YAG laser is used to cut the multi-layer board. The most considerable matter in the laser cutting of the multi-layer BGA boards is their different absorption coefficient to the laser beam and their different heat conductivity. The cut mechanism of a multi-layer BGA board using a 2$^{nd}$ harmonic Nd:YAG laser is the thermal vaporization by high temperature rise based on the Gaussian profile and copper melting point. In this experiment, we found that the sacrifice layer and Na blowing are effective in minimizing the surface burning by the reaction between oxygen in the air and the laser beam. In addition, N2 blowing reduces laser energy loss by debris and suppresses surface oxidation. Also, the beam incidence on the epoxy layer compared to polyimide was much more suitable to reduce damage to polyimide with copper wire for the multi layer BGA singulation. When the polyester double-sided tape is used as a sacrifice layer, surface carbonization becomes less. The SEM, non-contact 3D inspector and high-resolution microscope are used to measure cut line-width and surface morphology.