• Computers and Concrete
• /
• 제19권6호
• /
• pp.617-623
• /
• 2017

This work is conducted with the aim of using waste material to reserve the natural resources. The objective is accomplished by conducting experimentation and verify by modeling based on fuzzy logic. In experimentation, concrete is casted by using natural/river sand as fine aggregate and termed as control specimen. Natural sand is conserved by replacing it with used foundry sand (UFS) by an amount of 10, 20 and 30% by weight. Fresh and hardened properties of concrete are investigated at different ages. It is observed that compressive strength and modulus of elasticity reduced with the increase in amount of UFS. Furthermore, concrete compressive strength is predicted by using fuzzy logic model and verified at different replacement ratio and age with experimental observations.

• 한국안전학회지
• /
• 제30권1호
• /
• pp.66-71
• /
• 2015

Safety, resilience and comfort of pedestrian were assessed by the British Pendulum Test and SB/GB factor test at 8 kinds of sidewalk pavement. Sidewalk paving materials were normal concrete, porous concrete, concrete block, soil concrete, asphalt, rubber chip/resin mixture, wood chip/resin mixture and floor tile. In addition, a survey was conducted to investigate the perception of pedestrians on the sidewalk paving material. As a result, while the skid resistance value was measured in the most 60BPN above, the floor tile showed a low value of about 30BPN. The ratios of SB factor to GB factor of the elastic pavements(rubber/resin mixture and wood chip/resin mixture) appeared to be relatively large when compared with those of the conventional sidewalks. The survey showed that respondents perceived as more safe and comfortable elastic pavements compared to conventional pavements. Approximately 50% of respondents answered that hardened soil pavement was the most environmentally friendly.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1993년도 봄 학술발표회 논문집
• /
• pp.34-39
• /
• 1993

Recently inappropriate aggregates are used as a raw material for ready-mixed concretes, due to the shortage of natural aggregate resources and the prohibition of their extraction for the environmental protection. We, therefore, have conducted experiments to obtain some knowledge of properties of domestic aggregates and to investigate subsequent changes in the properties of the fresh and hardened concretes. To this end, aggregates currently used in 13 domestic ready-mixed concrete plants were collected. Most of aggregate used in this experiment satisfied the KS in density and unit weight. But some of the aggregates have the particle size distribution that can effect bad influence on concrete. In this experiment the aggregates are found to have a bad particle size distribution, resulting in high amount of a unit water content and a unit cement content in concrete.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.15-218
• /
• 1999

Concrete is the most generous, universal main structural material. There is active study for processing quality, stable quality mangement. Especially, strength is basic factor of evaluating stability of concrete building. Regaining required strength and homogeneity is very important to get self-stability in building to evaluate another characteristic. Concrete strength is important to the quality management. But, result of hardened concrete's quality test is hardly reflected to works immediately. When required strength is not enough, it could bring out safe problem, economic and administrative cost. It is pointed out that problems from strength evaluation, so early evaluation of concrete quality is required. From the trend that accelerating high quality concrete development, improving the method of quality test and early evaluation measure is urgent project. Throughout this report, it is suggested the method with use of microwave to evaluate 28-days concrete strength.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.281-286
• /
• 2001

The development of automobile, vessel, rail road, and machine industry leads increase of foundry production used as their components, which cause a by-product, waste foundry sand (WFS). The amount of the WFS produced in Korea is over 900,000 ton a year, but most WFS buries itself and only 5~6% WFS is recycled as a material in construction materials. In this study, WFS is used as a fine aggregate for concrete. Five types of concretes aimed at the specified strength of 240$\pm$10 kgf/$cm^{2}$ , air contents of 4.5$\pm$1% and slump of 12$\pm$1.5cm were mixed with washed coarse seashore sand(WFS) in which salt was removed and then optimum mix proportion of concrete was determined. Moreover, basic properties such as setting time, workability, bleeding and slump loss of the fresh concrete with WFS were tested and compared with those of the concrete mixed without WFS. In .addition, both compressive strength of hardened concrete at each ages and tensile strength of it at the age of 28 days were measured and discussed.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 봄 학술발표회 논문집
• /
• pp.142-147
• /
• 1994

Lately, among concrete component used in construction works, the aggregate is the most important material because it hold about 70~80 Vo1% of most structural materials. Considering that the demand of aggregate is on the continuous increase in the construction works year after year, it is a very urgent thing to develop a substitute aggregate for river aggregate. This paper, an experimental study on the effect of corrosion protection by tighting concrete used fly-ash and silica fume, is to investigate workability and engineering properties of concrete used fly-ash and silica fume. As a test results, contrary to SF, workability of concrete used FA is inclined to be improved. And in the case of containing SF, the compressive strength containing admixtures is higher than plain concrete with increasing curing age.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.207-208
• /
• 2012

This study is aimed to utilize for basic material of concrete quality management through evaluate properties of fresh and hardened concrete with the aggregate quality. As a result, fine aggregate's slump change of between one grade was 8~82% and in case of coarse aggregate, slump change of between one grade was 2~22% on same mixing condition. The unit water for same workability condition, unit water was increased 16kg/㎥ with decreasing of one grade for fine aggregate and unit water was increased 5kg/㎥ with decreasing of one grade for coarse aggregate.

• 대한기계학회논문집A
• /
• 제24권4호
• /
• pp.900-906
• /
• 2000

Ceramic, PCD and CBN tools are available for the difficult-to-cut-materials such as hardened carbon tool steel, stainless steel, Inconel 718 and etc. Ceramic tools are likely to be chipped and abruptly broken before the appearance of normal wear in turning. Ceramic tools are suitable for continuous in turning, not for intermittent in milling. In this study, TiN/TiCN multi-layer coated ceramic tools were found to restrain the chipping, breaking and early fracture and to increase the critical cutting speed owing to TiN/TiCN multi-layer coating in Arc Ion Plating of PVD method.

• 한국생산제조학회지
• /
• 제9권2호
• /
• pp.87-95
• /
• 2000

By using AIP(Arc Ion Plating) of a physical vapor deposition for the first time in Korea a ceramic tool whose surface is coated single layeredly with TiN is developed. In addition cutting resistance appearing in the process of finishing cut of hardened carbon tool steel STC3 is studied. The principal and radial components of cutting resistance in those cutting conditions appear to be the same or similar and the feed component is relatively small. The feed component is found to be in proportion to cutting width and the radial component in proportion to cutting thickness. Owing to coating the cutting resistance of a TiN coated ceramic tool increas-es compared with that of a general ceramic tool.

• 한국정밀공학회지
• /
• 제14권12호
• /
• pp.121-126
• /
• 1997

The use of CBN tool material has been greatly increased because of the superior metal cutting performance for the machining of hardened steel. This paper presents some experimental results on the ball endmiling of harened steels. Three different hardnesses of STD11 workpieces were machined using CBN ball endimills, and the machining characteristics including cutting forces tool wear, and surface roughness of machined surface were compared. It has been found that the CBN ball endmill works better in the machining of harder workpieces. The microscopic examination explains that this unusual phenomenon is caused by the difference of microstructure of each workpieces.