• Nuclear Engineering and Technology
• /
• 제41권7호
• /
• pp.921-928
• /
• 2009

As part of an evaluation for an in-vessel severe accident management strategy, a coolant injection into the reactor vessel under depressurization of the reactor coolant system (RCS) has been evaluated in detail using the SCDAP/RELAP5 computer code. A high-pressure sequence of a small break loss of coolant accident (SBLOCA) has been analyzed in the Optimized Power Reactor (OPR) 1000. The SCDAP/RELAP5 results have shown that safety injection timing and capacity with RCS depressurization timing and capacity are very effective on the reactor vessel failure during a severe accident. Only one train operation of the high pressure safety injection (HPSI) for 30,000 seconds with RCS depressurization prevents failure of the reactor vessel. In this case, the operation of only the low pressure safety injection (LPSI) without a HPSI does not prevent failure of the reactor vessel.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 추계학술발표회논문집(1)
• /
• pp.395-400
• /
• 1996

Scoping analyses for the Safety Injection System (SIS) configuration for Korean Next Generation Reactor (KNGR) are peformed in this study. The KNGR SIS consists of four mechanically separated hydraulic trains. Each hydraulic train consisting of a High Pressure Safety Injection (HPSI) pump and a Safety Injection Tank (SIT) is connected to the Direct Vessel Injection (DVI) nozzle located above the elevation of cold leg and thus injects water into the upper portion of reactor vessel annulus. Also, the KNGR is going to adopt the advanced design feature of passive fluidic device which will be installed in the discharge line of SIT to allow more effective use of borated water during the transient of large break LOCA. To determine the feasible configuration and capacity of SIT and HPSI pump with the elimination of the Low Pressure Safety Injection (LPSI) pump for KNGR, licensing design basis evaluations are performed for the limiting large break LOCA. The study shows that the DVI injection with the fluidic device SIT enhances the SIS performance by allowing more effective use of borated water for an extended period of time during the large break LOCA.

• Journal of Mechanical Science and Technology
• /
• 제17권9호
• /
• pp.1380-1387
• /
• 2003

When a cold HPSI (High pressure Safety Injection) fluid associated with an overcooling transient, such as SGTR (Steam Generator Tube Rupture), MSLB (Main Steam Line Break) etc., enters the cold legs of a stagnated primary coolant loop, thermal stratification phenomena will arise due to incomplete mixing. If the stratified flow enters the downcomer of the reactor pressure vessel, severe thermal stresses are created in a radiation embrittled vessel wall by local overcooling. As general thermal-hydraulic system analysis codes cannot properly predict the thermal stratification phenomena, RG 1.154 requires that a detailed thermal-mixing analysis of PTS (pressurized Thermal Shock) evaluation be performed. Also. previous PTS studies have assumed that the thermal stratification phenomena generated in the stagnated loop side of a partially stagnated primary coolant loop are neutralized in the vessel downcomer by the strong flow from the unstagnated loop. On the basis of these reasons, this paper focuses on the development of a 3-dimensional thermal-mixing analysis model using PHOENICS code which can be applied to both partial and total loop stagnated cases. In addition, this paper verifies the fact that, for partial loop stagnated cases, the cold plume generated in the vessel downcomer due to the thermal stratification phenomena of the stagnated loop is almost neutralized by the strong flow of the unstagnated loop but is not fully eliminated.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 1998년도 춘계 학술발표회 논문집
• /
• pp.159-165
• /
• 1998

한정된 자원의 효율적인 배분을 통하여 원자력발전소를 최적정비 하고자 신뢰도중심정비전략이 수립되고 있다. 본 연구에서는 영광 1,2호기 신뢰도중심정비 연구의 시범계통인 고압안전주입계통에 대하여 확률론적 안전성평가 모델을 이용하여 노심손상 빈도에 대한 중요도를 분석하였다 고압안전주입계통의 신뢰도 모델을 재구성하여 16개 초기사건에 대한 노심손상 빈도를 제정량화 하였고 고압 안전주입계통 고장수목에 모델링된 74개의 기본사건에 대하여 노심손상 빈도에 대한 중요도를 평가하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.51-54
• /
• 2002

When a cold HPSI (High Pressure Safety Injection) fluid associated with an design basis accident, such as LOCA (Loss of Coolant Accident), enters the cold legs of a stagnated primary coolant loop, thermal stratification phenomena will arise due to incomplete mixing. If the stratified flow enters a reactor pressure vessel downcomer, severe thermal stresses are created in a radiation embrittled vessel wall by local overcooling. Previous thermal-mixing analyses have assumed that the thermal stratification phenomena generated in stagnated loop of a partially stagnated coolant loop are neutralized in the vessel downcomer by strong flow from unstagnated loop. On the basis of these reasons, this paper presents the thermal-mixing analysis results in order to identify the fact that the cold plume generated in the vessel downcomer due to the thermal stratification phenomena of the stagnated loop is affected by the strong flow of the unstagnated loop.

• 한국분무공학회지
• /
• 제8권1호
• /
• pp.23-28
• /
• 2003

When a cold HPSI (High Pressure Safety Injection) fluid associated with a design basis accident, such as LOCA (Loss of Coolant Accident), enters the cold legs of a stagnated primary coolant loop, thermal stratification phenomena may arise due to incomplete mixing. If the stratified flow enters a reactor pressure vessel downcomer, severe thermal stresses are created in a radiation embrittled vessel wall by local overcooling. Previous thermal-mixing analyses have assumed that the thermal stratification phenomena generated in stagnated loop of a partially stagnated collant loop are neutralized in the vessel downcomer by strong flow from unstagnated loop. On the basis of these reasons, this paper presents the thermal-mixing analysis results in order to identify the fact that the cold plume generated in the vessel downcomer due to the thermal stratification phenomena of the stagnated loop is affected by the strong flow of the unstagnated loop.

• Nuclear Engineering and Technology
• /
• 제36권6호
• /
• pp.497-511
• /
• 2004

A PSV (pressurizer safety valve) popping test carried out in the early phases of a refueling outage may trigger a test-induced LOCA(loss of coolant accident) if a PSV fails to fully close and is stuck in a partially open position. According to a KSNP (Korea standard nuclear power plant) low power and shutdown PSA (probabilistic safety assessment), the failure of a high pressure safety injection (HPSI) accompanied by the failure of a PSV to fully close was identified as a dominant accident sequence with a significant impact on low power and shutdown risks (LPSR). In this study, we aim to investigate and verify a new means for mitigating this type of accident using a thermal-hydraulic analysis. In particular, we explore the applicability of an aggressive cool-down combined with operator actions. The results of the various sensitivity studies performed there will help reduce LPSR and improve Refueling outage safety.

• Nuclear Engineering and Technology
• /
• 제28권3호
• /
• pp.257-264
• /
• 1996

The conventional Equipment Environment Qualification (EEQ) envelope is developed based on the containment responses during the design basis events. The Safety Depressurization System (SDS) design without In-containment Refueling Water Storage Tank (IRWST) adopted in the Ulchin 3&4 challenges the conventional EEQ envelope during long term Feed and Bleed (F&B) operation due to the direct discharge of high mass and energy into the containment. Therefore, it is necessary to confirm that the containment pressure and temperature history during the long term F&B operation does not violate the conventional EEQ envelope. However, this subject has never been quantitatively assessed before. To investigate the success path of long term F&B operation this paper analyzes the thermal hydraulic response of the containment and Reactor Coolant System (RCS) until the completion of depressurization and cooldown of RCS into Shutdown Cooling System (SCS) entry condition. It is found that the SCS entry condition can be reached within 6 hours without violating the EEQ curve by proper operation of SDS valves, High Pressure Safety Injection (HPSI) pumps and active Containment Heat Removal System (CHRS). The suggested strategy not only demonstrates the feasibility of long term F&B operation but also can be utilized in the preparation of Emergency Procedure Guidelines (EPGs)

• Nuclear Engineering and Technology
• /
• 제31권1호
• /
• pp.17-28
• /
• 1999

A thermal-hydraulic analysis is conducted on the loss-of-coolant-accident (LOCA) during shutdown operation of YGN Units 3/4. Based on the review of plant-specific characteristics of YGN Units 3/4 in design and operation, a set of analysis cases is determined, and predicted by the RELAP5/MOD3.2 code during LOCA in the hot-standby mode. The evaluated thermal-hydraulic phenomena are blowdown, break flow, inventory distribution, natural circulation, and core thermal response. The difference in thermal-hydraulic behavior of LOCA at shutolown condition from that of LOCA at full power is identified as depressurization rate, the delay in peak natural circulation timing and the loop seal clearing (LSC) timing. In addition, the effect of high pressure safety injection (HPSI) on plant response is also evaluated. The break spectrum analysis shows that the critical break size can be between 1% to 2% of cold leg area, and that the available operator action time for the Sl actuation and the margin in the peak clad temperature (PCT) could be reduced when considering uncertainties of the present RELAP5 calculation.

• Nuclear Engineering and Technology
• /
• 제27권4호
• /
• pp.470-482
• /
• 1995

2025 MWt 가압경수로인 울진 3, 4호기에는 설계기준초과사고인 완전급수상실사고를 완화하기 위하여 안전감압계통이 채택되었다. 본 논문은 울진 3, 4호기의 안전감압계통의 방출유량을 결정하기 위한 해석방법 및 결과에 대하여 논의하였다. 안전감압계통의 방출용량을 다음과 같은 두가지의 설계요건에 따라 결정하였다 : 1) 두 개의 고압안전주입펌프 중 하나의 펌프만이 작동하고 운전원이 안전감압계통의 한 계열의 감압경로를 가압기안전밸브가 열리자마자 개방하였을 경우 노심노출을 방지하여야 한다 2) 두 개의 고압안전주입펌프가 모두 작동하고 두 계열의 안전감압경로를 가압기안전밸브가 열린 후 30분 뒤에 개방하였을 경우 노심노출을 방지하여야 한다. CEFLASH-4AS/REM 전산코드의 모델 및 해석 결과의 타당성을 검토하기 위하여 REL-AP5/MOD3를 이용한 해석을 수행하였다. 운전원의 복구과정이 없을 경우와 운전원이 충전 및 유출운전에 의해 사고를 완화하는 경우의 완전급수상실사고 경위에 대해 수치모사를 수행하였다. 두 사고 경 위에 대해 CEFLASH-4AS/REM에 의해 예측된 원자로계통의 주요 열수력학적 거동이 RELAP5 /MOD3에 의한 결과와 정성·정량적으로 잘 일치하는 것을 알 수 있었다. 결론적으로 울진 3, 4호기에 대해 완전급수상실사고시 안전감압계통을 이용한 충전 및 유출운전에 의해 잔열제거 및 일차계통냉각재 재고량 유지가 성공적으로 이루어짐을 수치모사를 통해 확인 할 수 있었다.