• Journal of Broadcast Engineering
• /
• v.22 no.1
• /
• pp.28-41
• /
• 2017

In this paper, the fast encoding algorithm in High Efficiency Video Coding (HEVC) encoder was studied. For the encoding efficiency, the current HEVC reference software is divided the input image into Coding Tree Unit (CTU). then, it should be re-divided into CU up to maximum depth in form of quad-tree for RDO (Rate-Distortion Optimization) in encoding precess. But, it is one of the reason why complexity is high in the encoding precess. In this paper, to reduce the high complexity in the encoding process, it proposed the method by determining the maximum depth of the CU using a hierarchical clustering at the pre-processing. The hierarchical clustering results represented an average combination of motion vectors (MV) on neighboring blocks. Experimental results showed that the proposed method could achieve an average of 16% time saving with minimal BD-rate loss at 1080p video resolution. When combined the previous fast algorithm, the proposed method could achieve an average 45.13% time saving with 1.84% BD-rate loss.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.31 no.4
• /
• pp.5-11
• /
• 2023

This study was conducted to improve energy efficiency and problems such as clumping and fouling in the glue zone that occur in the moisture content range of 40 to 60% when sewage dehydration residue is directly fed into the dryer. The temperature of the hot air is low at 270~300℃, and the paddle-type flotation method and dehydrated residue are applied to the circulated heat storage media to increase the contact area with the hot air, thereby reducing energy recovery and gas emissions. The water content of the dried residue is 2.7. ~7 .5%, the heat of evaporation of moisture was 608.0~690.6 kcal/kg·H₂O, which confirmed an energy saving effect of about 8.8% compared to the heat of evaporation of moisture of 714.5 kcal/kg·H₂O when no heat storage media was used.

• Proceedings of the Korean Society of Embryo Transfer Conference
• /
• 2002.11a
• /
• pp.83-83
• /
• 2002

The purpose of this study was to investigate the warming temperature and exposed time on the post-thaw survival rate and viability of bovine blastocyst cryopreserved by GMP vitrification. Groups of three bovine IVP blastocysts were sequentially placed into vitrification solution before being loaded into the GMP straws and immersed into LN$_2$within 20 to 25 sec. The warming rate was increased 2 times of warming temperature for improvement of post-thaw survival rates. The frozen embryos were warmed either at 35 or 70$^{\circ}C$ for 1 or 2 sec and then diluted in sucrose solution. Post-thaw blastocysts were serially washed in 0.25 and 0.15 M sucrose in holding medium (HM: TCM199 supplemented with 10% FCS) and TCM-199 for each 5 min, respectively, and then cultured in TCM199 for 24 h. The rate of re-expanded blastocyst was significantly different fer 35 and 70$^{\circ}C$ warming temporature (76.4 vs. 89.3%; P<0.05). The rate of re-expanded blastocyst at 70$^{\circ}C$ for 1 sec was significantly higher than that for 2 sec (91.1 vs. 70.9%; P<0.05). The number of nuclei counted were significantly different among control, 35 and 70$^{\circ}C$ (121${\pm}$8.5 vs. 104${\pm}$11.7 vs. 114${\pm}$10.3; P<0.05). These results indicated that the increasing of warming rate can provide high survival rates of bovine IVP blastocysts. Especially, the best viability of post-thaw blastocyst could be thaw at 70$^{\circ}C$ for 1 sec. The warming temperature and exposed time far warming was considered to be limiting factors to the viability of bovine IVP embryos. he purpose of this study was to investigate the warming temperature and expose.

• IEIE Transactions on Smart Processing and Computing
• /
• v.1 no.3
• /
• pp.152-160
• /
• 2012

This paper proposes a frame-level rate control algorithm for low delay video applications to reduce the fluctuations in the bitrate. The proposed algorithm minimizes the bitrate fluctuations in two ways with minimal coding loss. First, the proposed rate control applies R-Q model to all frames including the first frame of every group of pictures (GOP) except for the first one of a sequence. Conventional rate control algorithms do not use any R-Q models for the first frame of each GOP and do not estimate the generated-bit. An unexpected output rate result from the first frame affects the remainder of the pictures in the rate control. Second, a rate-distortion (R-D) cost is calculated regardless of the hierarchical coding structure for low bitrate fluctuations because the hierarchical coding structure controls the output bitrate in rate distortion optimization (RDO) process. The experimental results show that the average variance of per-frame bits with the proposed algorithm can reduce by approximately 33.8% with a delta peak signal-to-noise ratio (PSNR) degradation of 1.4dB for a "low-delay B" coding structure and by approximately 35.7% with a delta-PSNR degradation of 1.3dB for a "low-delay P" coding structure, compared to HM 8.0 rate control.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2007.11a
• /
• pp.305-306
• /
• 2007

ACP(Advanced Spent Fuel Conditioning Process)의 금속전환로에 $U_3O_8$을 공급하기 위하여 20 kgHM/batch의 $UO_2$ 펠릿(pellets)을 처리할 수 있는 건식분말화 장치가 개발되고있다. 건식분말화 장치는 500 $^{\circ}C$온도에서 공기를 공급하여 일정한 입도범위의 균질한 $U_3O_8$을 만든다. 이런 건식 분말화 장치의 효율을 높이기 위해서는 반웅로에 불어 넣어주는 공기의 유량을 증가시킬 필요가 있다. 하지만 공기와 반응하여 생성되는 $U_3O_8$ 입자는 그 크기가 최소 3 ${\mu}$m 정도로 매우 미세하여，반응로 출구를 통해 외부로 빠져나갈 가능성 이있다. 이를 방지하기 위해 분말화 장치 출구 바깥에는 필터가 설치되어 있으나 공기와 함께 $U_3O_8$ 입자가 계속해서 빠져 나갈 경우 입자로 인해 필터가 막혀 제 기능을 할 수 없게 된다. 따라서 건식 분말화 장치는 미세한 $U_3O_8$ 입자가 반응로 밖으로 빠져나가지 않도록 입구에서의 공기 유량을 일정 수준 이하로 조절해주는 것이 필요하다. 이 연구의 목적은 초기 유량으로부터 유량을 점점 증가시키면서 시간변화에 따른 입자 거동 특성을 해석하며， 결과로부터 주어진 크기의 타원입자에 대해 최대 허용 공기 유량을 결정하고자한다. 이 해석을 위해 유동과 입자를 동시에 해석할 수 있는 ANSYS-CFX 5.7.1과 ANSYS-CFX 10.0 두 가지의 소프트웨어가 사용되었다. 해석 결과를 바탕으로 좀더 정확한 유량 한계치 계산을 위해 추가로 수행되어야 할 해석에 대해 제안하였다.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.1
• /
• pp.118-128
• /
• 2001

This study was performed to evaluate the toothbrush abrasion characteristics of seven commercially available light-cured cervical restorative materials one resin-modified glass-ionomer material(Fuji II LC) three polyacid-modified composites(Compoglass, Dyract, F2000), and three light-cured composites(Heliomolar, Palpique Estelite, UniFil F). All samples were stored in distilled water at $37^{\circ}C$ for 10 days. 2.0N of weight was loaded during the test and the abraded surfaces were examined with profilometer and SEM after 100,000 cycles. The results obtained were summarized as follows; 1. The highest hardness value of 79.7 was observed in the FT group and the lowest value of 20.0 was observed in the HM group. Results of Tukey test showed that an overall significant difference was indicated except the CG and DR groups(p<0.05). 2. The highest surface roughness was observed in the FL group and the lowest was observed in the UF group. Results of Tukey test showed the significant difference between the FL or FT and UF groups(p<0.05). 3. Statistically higher abrasion and surface roughness were observed for the dentifrice of paste type, Perio A+, than for that of gel paste type, Tom & Jerry. 4. The surface roughness values increased on the abraded surfaces because of the protrusion of filler particles due to selective removal of matrix resin.

• Journal of Digital Contents Society
• /
• v.18 no.1
• /
• pp.141-147
• /
• 2017

Scalable extension of High Efficiency Video Coding (SHVC) standard uses the up-sampled residual data from the base layer to make a residual data in the enhancement layer. This paper describes an efficient algorithm for improving coding gain by using the filtered residual signal of base layer in the Scalable extension of High Efficiency Video Coding (SHVC). The proposed adaptive filter selection mechanism uses the smoothing and sharpening filters to enhance the quality of inter-layer prediction. Based on two filters and the existing up-sampling filter, a rate-distortion (RD)-cost fuction-based competitive scheme is proposed to get better quality of video. Experimental results showed that average BD-rate gains of 1.5%, 2.1%, and 1.7% for Y, U and V components, respectively, were achieved, compared with SHVC reference software 5.0, which is based on HEVC reference model (HM) 13.

• Korean Journal of Animal Reproduction
• /
• v.23 no.1
• /
• pp.85-92
• /
• 1999

This study was designed to determine effect of cryoprotectant kinds and cell stages on OPP vitrification method in mouse embryos. The freezing speed, cryoprotectants and cell stage could affect of embryo viability following various vitrification methods. The vitrification solution used were consisting of 40% (v/v) ethylene glycol, 18% (w/v) Ficoll, 0.3 M sucrose solution in holding medium (D-PBS supplemented with 5% FCS: HM) (EFS) or 16.5% ethylene glycol , 16.5% dimethyl sulfoxide, 0.5 M sucrose in HM (EDS). The embryos were collected from oviduct at 18 h after hCG injection and then washed and cultured in mHTF medium until use. In experiment 1, the blastocysts were vitrified by OPP straw to determine the optimal vitrification solution of EFS or EDS. The post-thaw survival rates at re-expanded stage rates were significantly different between EFS and EDS (95.0 vs 100%), but at hatching stage was not different between EFS and EDS (90.0 vs 95.0%). respectively. In experiment 2, zygotes, 2-, 4-cell, morula and blastocysts were vitrified by OPP method to determine the acceptable of early stage embryos. The development rates to expanded blastocyst in zygote (70.0%) were significantly lower rather than those in 2-, 4- 8-cell, compacted morula or blastocyst (89.7, 90.0, 92.8, 97.6 or 97.5%), respectively. However, the cell number of post-thaw developed to expanded blastocyst in blastocyst and control blastocyst stage (39.6$\pm$2.81, 35.7$\pm$2.98) were significanty higher than those in zygote, 2-, 4-, 8-cell, compacted morula (29.8$\pm$3.21, 31.3$\pm$3.83, 29.3$\pm$3.58, 28.9$\pm$3.21 or 30.8$\pm$2.93). In experiment 3, the zygotes were exposed in VSl for 1, 2, and 3 min to the optimal exposed time. The cleavage rates (91.6, 88.5, 88.9%) and develop mental rates to blastocyst (83.3, 74.3 and 69.4%) depends on the exposed time in VSl were not significantly different among 1, 2, or 3 min, respectively. The cell number also were not significantly different among exposed time in VS1. respectively. These results indicate that OPP method could be useful for vitrification either EFS or EDS vitrification solution. The post-thaw survival rates at zygote were significantly lower than those at 2-, 4-, 8-cell, morula or blastocyst, respectively. The zygote stage were more sensitive rather than late stage embryos. The exposing time in VS1 for 1 min was better than that for 2 or 3 min, even it was not significantly different. The OPP vitrification method could be useful of mouse embryos either with EFS or EDS vitrification solution.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.1103-1107
• /
• 2009

최근 기상이변에 따른 국지성 호우 등으로 인하여 지역별로 홍수량 차이가 많이 나고 있는 상황으로 유역내 중요시설물 및 인명의 보호를 위해서는 유역의 특성을 정확하게 반영한 홍수분석이 필수적인 실정이다. 유역 주요지점의 정확한 홍수량을 산정하기 위해서는 지역특성이 반영된 호우를 선정하고, 유출모의를 위한 유역특성이 잘 구현되어야 한다. 이를 위해서는 홍수량산정에 영향을 주는 매개변수의 정확한 산정이 필요하며 본 연구에서는 미공병단(US Army Corps)에서 개발하여 배포한 차세대 프로그램인 HEC-HMS(v3.3)를 이용하여 집중시간, 저류상수, Curved Number, 감수상수, 초기손실, 초기기저유량, Threshold 등 7가지 매개변수에 대한 최적화를 수행하였다. 종래에는 첨두홍수량을 중시하여 집중시간과 저류상수는 최적화하고 나머지 변수들은 실측치 및 계산값을 적용하였으나, 금번 연구에서는 첨두홍수량 및 총유출량 모두 관측값에 최대한 일치하도록 7가지 매개변수를 최적화하는 방안 및 최적화시 초기값 선정이 매개변수 최적화에 미치는 영향을 연구하였다. 매개변수 최적화 순서는 먼저 전체적인 평균유출량 또는 평균유출고가 실측치와 모의치 간에 일치하도록 CN, RC를 보정하고 다음 단계로 첨두발생시간이 일치하도록 Tc, K를 보정하고, 마지막으로 홍수 수문곡선의 형태를 결정하는 나머지 매개변수를 조정하여 전체적인 수문곡선의 형태와 첨두홍수량이 일치하도록 수행하였으며, Tc, K, CN 등의 중요 매개변수는 신뢰구간(계산치의 0.8${\sim}$1.2)을 설정하여 목적함수의 수렴을 유도하였다. 위를 이용하여 수렴된 매개변수들로 강우-유출 모의를 분석한 결과를 기존 홍수사상과 비교한 결과 상당히 근접한 결과를 도출할 수 있어, 매개변수는 7가지 모두에 대한 최적화를 가능한 것으로 연구되었으나 목적함수들의 수렴되는 과정에 대해서는 좀 더 심도있는 고찰이 필요할 것으로 판단된다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.255-261
• /
• 2020

This study was undertaken to evaluate the growth, body shape and carcass cutting yield traits of Duroc (D) and crossbred (Duroc×Pietrain×Pietrain; DPP) pigs. A total of 147 D and 101 DPP pigs were used for analyzing the growth trait, whereas 16 D and 16 DPP pigs were evaluated for carcass yields. Backfat thickness (BF) and average daily feed intake (ADFI) were significantly higher in D (14.07±0.24 mm, 2,101 g) than in DPP (12.69±3.25 mm, 1,909 g) (p <0.001). Moreover, D exhibited significantly higher body shape traits including body height (BH), chest depth (CD) and chest width (CW), as compared to DPP pigs (p <0.001). No differences were observed for body length (BL) between the two strains. Analysis of the carcass cutting yield traits determined for D and DPP were in the order: ham (HM; 31.17% and 33.43%), belly (BY; 23.40% and 19.55%), and picnic shoulder (PS; 16.54% and 16.87%), respectively. Then, HM showed a difference of 2.26% P with D(31.17%) and DPP(33.43%), while BY showed a difference of 3.85% P with D(23.40%) and DPP(19.55%). Taken together, our results indicate that DPP has a better feed efficiency than D, and therefore has the potential to increase the production of low-fat pork, targeting consumers having a high preference who have opted for a healthy lifestyle. These results can be used as basic data for developing an ideal pig breed.