• Analytical Science and Technology
• /
• v.7 no.2
• /
• pp.237-243
• /
• 1994

The stability of W/O emulsions (milk fat : water=4 : 1, w/w) containing various emulsifiers was compared to determine the effect of different chemical types of emulsifiers in relation to the change of HLB value caused by emulsifier type and the influence of single vs. binary emulsifier systems. These variables were compared at emulsifier HLB values of 0.5~16.7 and at emulsifier concentrations of 1.0~3.0%(w/w). Eleven emulsifiers used as 11 different single mixtures and 16 different binary mixtures were evaluated in W/O type emulsion systems containing 20.0%(w/w) of water in milk fat. This W/O emulsion was stable (more than 90.0 of ESI value) in the range of low value of emulsifier HLB (less than 4.7 of HLB value). All the ESI values of binary emulsifier systems were higher than those of single emulsifier systems. But, the influence pattern of emulsifier HLB on this emulsion stability in single emulsifier systems was very similar to the trend in binary emulsifier systems.

• Korean Journal of Food Science and Technology
• /
• v.30 no.5
• /
• pp.1114-1119
• /
• 1998

The stabilities of O/W emulsions (lipophilic core material:lipophobic wall material=3:2, w/w) containing various kinds of emulsifiers were compared to determine the optimal conditions of the HLB (hydrophilic lipophilic balance) value, the concentration and composition of emulsifier, the ratio of core material to the wall material, and the concentration and composition of polymers in the wall material. The effect of different chemical types of emulsifiers and the influence of single vs. binary emulsifier systems were compared with 13 kinds of emulsifier HLB values of $0.6{\sim}16.7$ at the concentration of 0.50%(w/w). The emulsion system was stable (more than 99.0 of ESI value) when the HLB value of the emulsifier was more than 11.0 or less than 2.8 of emulsifier HLB value. But it was unstable (less than 40.0 of ESI value) at the HLB value of the emulsifier between 3.4 and 8.6. Especially, we could find out the emulsion containing the emulsifier of polyglycerol polyricinoleate (PGPR, HLB 0.6) became stable creamy state. And, the ESI value of binary emulsifier system containing 0.25%(w/w) of PGPR and 0.25%(w/w) of polyoxyethylene sorbitan monolaurate (PSML, HLB 16.7) was higher than that of any single emulsifier system at the concentration of 0.50%(w/w). The highest emulsion stability was obtained in the liquefied wall material composed of 0.25%(w/v) of waxy corn starch and 0.50%(w/v) of agar.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.40 no.3
• /
• pp.227-236
• /
• 2014

In this study, O/W and W/S emulsions were prepared by combining oils having different required hydrophilic lipophilic balance (HLB) values under the diverse conditions of HLB values composed of a hydrophilic surfactant and a lipophilic surfactant and their stability was investigated. Results showed that the higher the viscosity of O/W emulsions was as the lower the HLB value of emulsifier and emulsion particle showed a tendency to be a smaller and compact and stabler in centrifugal filtration. W/S emulsions also showed a similar tendency to be a smaller and compact as HLB values of emulsifier was higher and stabler in centrifugal filtration. However, the viscosity of W/S emulsion tended to get lower in HLB conditions of all emulsifiers as the time passed. This indicated that the emulsions had an unstable feature in long-term stability. In conclusion, the results showed opposite to the known theory that O/W emulsion is proper to be applied by nonionic surfactant with a high HLB value and W/S emulsion to be applied by nonionic surfactant with a low HLB value and provide useful information for the cosmetics research and related areas.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.6 no.4
• /
• pp.284-288
• /
• 2001

Lipid emulsions with saturated triacylglycerols (TAGs) with 4 to 10 carbons in each acyl chain were prepared to study how the oil component alters the stability of the lipid emul-sions when phosphatidylcholines were used as emulsifiers. The average droplet size of the emul-sions became smaller as the chain length of the TAG increased. For a given oil emulsion with smaller droplets was formed with an emulsifier having higher HLB value. The influence of HLB values on the droplet size was biggest for the tributyrin (C4) emulsion. For the tricaprylin(C8) emulsions, droplet size was identical at given emulsifier concentrations regardless of HLB values. The HLB value and the concentration of the emulsifiers also affect the droplet size of the emul-sions. The emulsions with smaller average droplet size were more stable than with bigger size for 20 days. The oil and water (o/w) interfacial tension in inversely proportional to the initial droplet size of the emulsion.

• Applied Chemistry for Engineering
• /
• v.29 no.4
• /
• pp.440-445
• /
• 2018

In this study, the stability of O/W cosmetic facial cream emulsions according to HLB values was evaluated by mixing nonionic surfactants, such as Brij 78&72 and Brij 98&92. Brij 78&72 (steareth-20&steareth-2, EMS-01), saturated fatty acid, and Brij 98&92 (oleth-20&oleth-2, EMS-02), unsaturated fatty acid, were used as mixed surfactants. The stability of the O/W emulsion was evaluated by using the emulsion viscosity, particle size, particle size distribution, and zeta-potential. The viscosity of the emulsion increased with the increase of time for EMS-01 while that of EMS-02 decreased with the increase of HLB value. The particle size of both EMS-01 and EMS-02 increased with time. The emulsifier with a HLB value of 10.8, which is the most similar to the required HLB value of mineral oil, 10.5, had the smallest particle size and highest density and also showed the highest emulsion stability. The zeta-potential of both emulsions tended to increase with the HLB value. No significant changes were observed in emulsions of the HLB value of 10.8 or more. The saturated fatty acid system, EMS-01, exhibited a higher zeta-potential value than that of the unsaturated fatty acid EMS-02 and also was superior in the stability.

• Journal of Environmental Science International
• /
• v.7 no.6
• /
• pp.875-881
• /
• 1998

Microemulsion is prepared by the method of phase inversion emulsification with d-limonene that is environmental friendly substance and nontoxic to human body as dispersed phase. Emulsifier used for preparation of microemulsion is nonionic surfactants, polyoxyethylene nonylphenyl ether. Stability of prepared microemulsion was estimated by the various method of ξ-potential, hydrodynamic diameter and electric conductivity. When d-limonene is emulsified by NP series, microemulsion is most stable and narrowly distributed at HLB value of 12.3(either one emulsifier or mixed emulsifiers). Stability of microemulsion is increased as the amount of emulsifiers is increased at same HLB value of 12.3. In the case of using the same amount of emulsifiers, number of produced micelle are relatively large as hydrodynamic diameter is small. Therefore, the state of microemulsion is stable and the electric conductivity is increased. One can determine that higher electric conductivity value means that microemulsion has more micelles and is more stable.

• Applied Chemistry for Engineering
• /
• v.30 no.4
• /
• pp.453-459
• /
• 2019

In this study, the influence factors on the stability of the O/W (oil in water) emulsions prepared with coconut oil and the nonionic mixed surfactant (Tween 80-Span 80) were evaluated. The concentration and HLB value of the nonionic mixed surfactant, and the degree of agitation were used as manufacture factors. The stability of prepared O/W emulsions were measured with the mean droplet size, zeta-potential, emulsion stability index (ESI), and thermal instability index (TII). The mean droplet size of the prepared O/W emulsions was from 100 to 200 nm. As the concentration of mixed surfactant and the homogenization speed increased, the droplet sizes decreased, while the zeta-potential values increased. The effect of HLB values increased in the order of 6.0, 10.0 and 8.0, and at the HLB value of 8 the smallest mean droplet size as 120 nm was obtained whereas the largest value of the zeta-potential between 10 and 60 mV. From the results of ESI and TII, the stability of prepared O/W emulsions increased in order of 6.0, 10.0 and 8.0 of HLB values, and ESI and TII values were above 80% and below 20% respectively at HLB value of 8.0.

• Journal of Adhesion and Interface
• /
• v.11 no.1
• /
• pp.9-14
• /
• 2010

O/W emulsions were prepared with the phase inversion emulsification methods. The emulsifiers were used the UNIQ-1 (isopropylamine alkyl aryl sulphonate) and UNIQ-2 (alkoxylated glycol ether). Investigated effect that HLB value, agitator velocity and manufacture temperature get in mean particle size of emulsions. Mean particle size receives much effect of HLB value. Also, estimated stability about storage temperature and light. Emulsion's mean particle size was 193 nm lastly, reduced VOC amount used 90% than existing alkyd resin.

• Applied Chemistry for Engineering
• /
• v.4 no.1
• /
• pp.196-203
• /
• 1993

Emulsions were prepared with the inversion emulsification method which adopted the agent-in-oil method-dissolving the mixed surfactants composed of the glycerin monostearate, polyoxyethylene(100) monostearate, and polyoxyethylene(20) sorbitan monostearate into mixtures of liquid paraffin and beeswax, and adding the aqueous solution of propylene glycol, gradually-and then their phases and viscosities behaviors in the emulsifying process were investigated. The fine and homogeneous o/w emulsions were formed in the HLB region (HLB 10.1~12.3), showing liquid crystalline phase and white gel phase in the emulsifying process. The phase inversion steps in the emulsifying process appeared as follows, i.e., oil continuous phase${\rightarrow}$liquid crystalline phase${\rightarrow}$white gel phase${\rightarrow}$o/w emulsion. Shear rate-shear stress curves of the prepared emulsions had the yield values which pointed out the existence of inner structure between emulsion particles, and the hysteresis loop which showed that the inner structure wasbroken irreversibly by the shear. The area of hystersis loop, an index of breakdown of inner structure, was increased with the decreasing of the HLB value of emulsifier, Shear time-shear stress curves showed the time dependence of plastic viscosity, and the relaxation time in time thinning behavior(${\lambda}$) indicated that the stability of emulsions prepared with the inversion emulsification method was decreased with the increasing of HLB values of emulsifier and was higher than that of emulsions prepared by homomixer.

• Applied Chemistry for Engineering
• /
• v.32 no.5
• /
• pp.562-568
• /
• 2021

An O/W (oil in water) emulsion, wheat germ oil raw material, was produced by using natural wheat germ oil and composite sugar-ester. The effects of variables such as the hydrophile-lipophile balance (HLB) value, added emulsifier amount, and emulsification time on the average particle size, emulsification viscosity and ESI of O/W wheat germ oil emulsion were investigated. The parameters of the emulsification process produced by the central composite design model of the response surface methodology (CCD-RSM), which is a reaction surface analysis method, were simulated and optimized. The optimum process conditions obtained from this paper for the production of O/W wheat germ oil emulsion were 8.4, 6.4 wt%, 25.4 min for the HLB value, amount of emulsifier, and emulsion time, respectively. The predicted reaction values by CCD-RSM model under the optimum conditions were 206 nm, 8125 cP, and 98.2% for mean droplet size (MDS), viscosity, and ESI, respectively, based on the emulsion after 7 days. The MDS, viscosity and ESI of the emulsion obtained from actual experiments were 209 nm, 7974 cP and 98.7%, respectively. Therefore, it was possible to design an optimization process for evaluating the stability of the emulsion of wheat germ oil raw material by CCD-RSM.