• 한국유체기계학회 논문집
• /
• 제7권2호
• /
• pp.21-26
• /
• 2004

In this study the effects of fluid viscosity on the pump performances for a conventional centrifugal pump were experimentally investigated. The study aimed to compare the pump characteristics between water and viscosity fluids. In order to measure the flow rate and pressure, v-notch welt and bourdon pressure gauges were used for the codes of KS B6301 and KS B6302. The working fluids were water, aqueous sugar and glycerin solutions. The results were summarized as follows : The experimental results were summarized as follows : the pump characteristics of the total head, shaft power, and efficiency with high viscosity fluids were different from those of water. When the viscosity of the applied fluid was increased, the total head and efficiency were more decreased than those of water. The decreasing gradients of the total head and the efficiency were larger than water due to the increased disk friction losses at the duty operation point. However, the shut-off head was almost constant regardless the viscosity of applied fluids. Each efficiency curves for the sugar $20w\%$ and glycerin $20w\%$ solutions was decreased up to $15.1\%$ and $34.4\%$ than that of water, respectively.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제22권1호
• /
• pp.5-10
• /
• 2011

The effect of sample handling condition on the rheological measurement of regenerated silk fibroin formic acid solution using parallel plate geometry was investigated. In case of loading method, the loading by pouring sample solution resulted in the best reproducibility of rheological measurement. Loading with spoon showed a high variance of viscosity value at low shear rate region ($0.01{\sim}1sec^{-1}$) while loading with syringe exhibited a low reproducibility of viscosity at high shear region ($1{\sim}100sec^{-1}$) with a disappearance of shear thinning phenomenon. It was revealed that the sample loading with small extra amount lead to the most reproducible result. The sample loading with the exact amount for the measuring plate resulted in a lack of reproducibility of high shear viscosity, while the loading with large extra volume produced a limited consistency of low shear viscosity. It was turned out that 3 min. of waiting time before measurement was the optimum condition for reliable result. When the waiting time was less than 1 min., the low shear viscosity was obtained with a lack of consistency. On the other hand, the sample solution started drying when the waiting time increased up to 5 min.

• Tribology and Lubricants
• /
• 제15권4호
• /
• pp.343-353
• /
• 1999

The role of viscosity index improver's(Ⅶ) additives for modem engine lubrication is complex. Under the condition of atmosphere or low shear rate, the characteristics of Ⅶ added lubricant is verified and quoted frequently for mathematical model of lubricant behavior. However, recent research shows that added lubricant has the characteristics of shear thinning at high shear rate condition although it performs well enough over the whole range of working temperature. At high shear rate, they show significant decrease of apparent viscosity irrespective of temperature. Many experimental researches verify that Ⅶ added lubricant shows boundary film layer formation on the solid surface as well as shear thinning effect by its polymeric molecular characteristics. The intend of our research is to verify the effects of Ⅶ from the viewpoint of continuum mechanics, because conventional Reynolds'equation with only pressure-viscosity relation cannot fully predict the lubricant behavior under the Ⅶ added condition. In these aspects, Reynolds'equation of Newtonian fluid model lacks the reflection of real fluid behavior and there is no way to explain the non-linear characteristics of Ⅶ added lubricant. In this research, we mathematically modeled the Ⅶ added lubricant behaviors which are the characteristics of non-Newtonian fluid behavior at high shear rate and boundary film formation on the solid surface. The consideration of elastic deformation in the contact region is also included in our computation and finally the converged film pressure and the film thickness with elastic deformation are obtained. The results are compared with those of Newtonian fluid model.

• 한국수소및신에너지학회논문집
• /
• 제29권6호
• /
• pp.648-653
• /
• 2018

Bran of barley causes high viscosity in bioethanol production due to the large amount of ${\beta}$-glucans and fiber. High viscosity is the main cause of decreased productivity and decreased facility efficiency in ethanol production. In order to prevent high viscosity, this study investigated the possibility of bioethanol from barley by debranning. As a result, it was able to reduced the viscosity (22.8 cP to 17.5 cP). And the fermentation speed and yield were improved as the activity of the enzyme and activity of yeast was also increased was improved due to the removal of non-fermentable components. In conclusion, debranning was advantageous in two ways. Firstly, bran removal increased the starch content of the feedstock and decreased viscosity of mash, improving ethanol fermentation. Secondly, by-products produced by debranning can use valuable products. It was remarkable results to the feasibility of bioethanol production from debranned barley.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.21-24
• /
• 2014

In the entrained-flow coal gasifier, coal ash turns into a molten slag most of which deposits onto the wall to form liquid and solid layers. Critical viscosity refers to the viscosity at the interface of the two layers. The slag layers play an important role in protecting the wall from physical/chemical attack from the hot syngas and in continuously discharging the ash to the slag tap at the bottom of the gasifier. For coal with high ash melting point and slag viscosity, CaO-based flux is added to coal to lower the viscosity. This study evaulates the effect of critical viscosity temperature and ash/flux ratio on the slag behavior using numerical modelling in a commercial gasifier. The changes in the slag layer thickness, heat transfer rate, surface temperature and velocity profiles were analyzed to understand the underlying mechanism of slag flow and heat transfer.

• 한국수소및신에너지학회논문집
• /
• 제26권6호
• /
• pp.581-589
• /
• 2015

In this study, the viscosity of a liquid carbon dioxide ($LCO_2$) that can potentially be used in a wet feed coal gasifier was evaluated. A pressurized capillary viscometer was employed to obtain the viscosity data of $LCO_2$ using two different methods. During the first method, the measurements were conducted under quasi-steady and high pressure flow conditions where two-phase flow was greatly minimized. The viscosity of $LCO_2$ was determined using turbulent friction relationship. At the second flow condition where unsteady flow is induced, the viscosity of $LCO_2$ was measured using the half-time pressure decay data and was further compared with values calculated by the first method.

• 공업화학
• /
• 제20권4호
• /
• pp.411-415
• /
• 2009

고점도인 최저급 폐유를 난방유로 대체하기 위하여 폐유에 희석용제로 경유,벙커C유를 이용하여 일정비율로 혼합한 후 연료 특성을 분석하였다. 혼합조건은 교반속도 3400~3600 rpm에서, 반응 시간을 30 s~30 min으로 조절하였고 반응온도는 $75{\pm}5^{\circ}C$로 유지하였다. 벙커C유, 경유를 이용하여 폐유의 점도를 낮춘 결과 최소 81%, 최대 96% 정도 감소되었다. 난방연료로서 폐유 : 벙커C유 : 경유의 최적 혼합 비율은 1 : 1 : 1이었으며 이 경우 인화점 $78^{\circ}C$, 동점도 $20.02mm^{2}/s$, 발열량 9158 kcal/L을 가짐을 확인하였다.

• 한국분무공학회지
• /
• 제27권2호
• /
• pp.77-83
• /
• 2022

In this study, the thickness of the liquid sheet formed by a low speed impinging jet onto a flat plate was measured by the direct contact method. The spatial distribution characteristics of the sheet thickness in the radial and circumferential directions, and the effects of jet velocity and liquid viscosity were analyzed. The measurement results were compared with the theoretical predictions. The wavy surface was observed in the case of low viscosity water, but not in the high viscosity aqueous glycerol solutions. The sheet thickness increased as the circumferential angle increased or the distance from the impinging point increased, but the thickness decreased as the circumferential angle increased around the impinging point. As the jet speed increased, the sheet thickness decreased, and the sheet thickness increased as the liquid viscosity increased. Comparison with the theoretical predictions showed that the measurement results agreed well in the case of low viscosity water or high viscosity liquids around the impinging point. The distribution characteristics of the sheet thickness can provide useful means for prediction of spray characteristics in splash plate injectors.

• 한국융합학회논문지
• /
• 제10권2호
• /
• pp.41-48
• /
• 2019

본 연구는 HPMC (Hydroxypropyl methyl cellulose)의 점도와 겉보기 점도가 유탕면의 흡유량과 지방 소화율에 미치는 영향을 확인하고자 하였다. HPMC 상업용 소재의 점도와 밀가루 대체 농도가 증가함에 따라 흡유량 감소와 지방 소화 지연 효과가 나타났다. 한편, 동일한 겉보기 점도를 보이는 수준으로 밀가루 대신 HPMC를 대체하여 제조한 유탕면에서도 겉보기 점도가 같음에도 불구하고 HPMC 자체 점도 증가(높은 중합도를 갖는 시료)에 따른 흡유량 감소와 지방 소화 지연효과를 볼 수 있었다. 이상의 결과로부터, 유탕면의 흡유량 감소와 지방 소화 지연은 겉보기 점도가 동일하다 하더라도 HPMC 자체의 높은 점도가 더 주요한 영향을 주는 것을 확인할 수 있었다.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2003년도 봄 학술발표회 논문집
• /
• pp.223-226
• /
• 2003

Due to the potential application to ultra-high strength fibers and excellent properties such as high mechanical properties, excellent thermal endurance and chemical stability, thermotropic liquid crystal polymers (TLCPS) are attractive in recent years [1, 2]. Furthermore, the melt blends of TLCPS and conventional thermoplastics have been extensively investigated because of their easy processing and high performance [3-6]. Since high performance polymers generally has high melt viscosity, introduction of the relatively low viscosity components may be one of the more effective techniques to improve processability through the decrement of melt viscosity in melt processing. (omitted)