• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.75-75
• /
• 2000

Recently, number of navigation system using GPS and other complementary sensors has been developed to offer high-position accuracy. In this paper, an integration of GPS and Dead-Reckoning, which consists of a fiber optical gyroscope and two high-precision wheel-motor encoders for a unmanned navigation system, is presented. The main objective of this integrated GPS/DR unmanned navigation system is to provide accurate position and heading navigation data continuously for autonomous mobile robot. We propose a method for increasing the accuracy of the estimated position of the mobile robot by its DR sensors, high-precision wheel-motor encoders and a fiber optical gyroscope. We used Kalman filter theory to combine GPS and DR measurements. The performance of GPS/DR navigation system is evaluated.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.11
• /
• pp.966-972
• /
• 2013

Measurement or estimation of tilt angle is necessary for balancing robot such as Segway which is considered as a next generation transportation vehicle. However, it requires high-cost accurate sensors to hold balancing during stationary and moving situations. In this paper, a tilt angle estimation of a plane rotating in a vertical plane using low-cost sensors. Estimation using a set of 2-axis orthogonal accelerometers along with an inaccurate rate gyro has been considered. Feasibility and performance of the proposed technique has been verified through some experimental results.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.3
• /
• pp.258-264
• /
• 2009

This paper presents two control algorithms for the frequency and amplitude of the resonator of a micro sensor. One algorithm excites the resonator at its a priori unknown resonant frequency, and the other algorithm alters the resonator dynamics to place the resonant frequency at a fixed frequency, chosen by the designer. Both algorithms maintain a specified amplitude of oscillations. The control system behavior is analyzed using an averaging method, and a quantitative criterion is provided for the selecting the control gain to achieve stability. Tracking and estimation accuracy of the natural frequency under the presence of measurement noise is also analyzed. The proposed control algorithms are applied to the MEMS dual-mass gyroscope without mechanical connecting beam between two proof-masses. Simulation results show the effectiveness of the proposed control algorithms which guarantee the proof-masses of the gyroscope to move in opposite directions with the same resonant frequency and oscillation amplitude.

• Journal of Sensor Science and Technology
• /
• v.23 no.4
• /
• pp.251-258
• /
• 2014

While the feasibility of vertical velocity as a threshold parameter for pre-impact fall detection has been verified, effects of sensor attachment locations and methods calculating vertical acceleration and velocity on the detection performance have not been studied yet. Regarding the vertical velocity-based pre-impact fall detection, this paper investigates detection accuracies of eight different cases depending on sensor locations (waist vs. sternum), vertical accelerations (accurate acceleration based on both accelerometer and gyroscope vs. approximated acceleration based on only accelerometer), and vertical velocities (velocity with attenuation vs. velocity difference). Test results show that the selection of waist-attached sensor, accurate acceleration, and velocity with attenuation based on accelerometer and gyroscope signals is the best in overall in terms of sensitivity and specificity of the detection as well as lead time.

• Journal of Sensor Science and Technology
• /
• v.5 no.4
• /
• pp.47-56
• /
• 1996

The basic principle and characteristics of a DTG(dynamically tuned gyroscope) are presented in this paper, which is used for the detection of disturbance and for the stabilization of gimbal. An accurate model of the rate mode DTG is proposed. This model has a resonance characteristics which is more similar to the characteristics of practical systems than the conventional 2nd order system model. Therefore, this model is applicable to the general rate mode gyroscope. Some problems at using DTG for a real electro optical tracking system are discussed and a solution is described.

• Journal of Sensor Science and Technology
• /
• v.21 no.3
• /
• pp.204-210
• /
• 2012

In this paper, signal detection and control circuits for hemispherical resonator gyroscope(HRG) are designed, simulated and tested. HRG is one of the coriolis vibratory gyroscope(CVG) which has very stable quartz hemispherical resonator and shows very precise performance. HRG signals are usually modulated at the several kHz of resonant frequency. So the general control scheme cannot be applied directly because general control schemes mainly focused at low frequency range. Using demodulated and modulated PI control scheme with the signal detection which is presented in this paper, performance of manufactured HRG has tested.

• International Journal of Aeronautical and Space Sciences
• /
• v.14 no.4
• /
• pp.379-386
• /
• 2013

The hemispherical resonator gyroscope is a type of vibratory gyroscope, which can measure angle or angular rate, based on its operating mode. This paper deals with the case when the hemispherical resonator gyroscope is operated in angle measurement mode. In angle measurement mode, the resonator pattern angle precesses, with respect to the external rotation input, by the principle of the Coriolis effect, so that the external rotation can be estimated, by measuring the amount of precession angle. However, this pattern angle drifts, due to the manufacturing error of the resonator. Since the drift effect causes degradation of the angle estimation performance of the resonator, the corresponding drift compensation control should be performed, to enhance the estimation performance. In this paper, a mathematical model of the hemispherical resonator gyro is first introduced. By using the mathematical model, a nonlinear observer for imperfection parameter estimation, and the corresponding compensation controller are designed to operate hemispherical resonator gyros, as angle measurement sensors.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2061-2063
• /
• 2003

This paper presents a method to compensate the drift of solid-state inertial sensors for control applications. A solid-state gyroscope is evaluated via both theoretical and experimental analyses. From the analytical results, a heuristic compensation method for the drift of the gyroscope is proposed. Experimental results on inverted pendulum control show that the proposed method is feasible since compensated signals from the gyroscope are successfully used in the feedback loop to control the inverted pendulum system.

• Journal of Sensor Science and Technology
• /
• v.25 no.2
• /
• pp.79-85
• /
• 2016

This paper proposes a threshold-based fall recognition algorithm to discriminate between falls and activities of daily living (ADL) using a tri-axial accelerometer and a bi-axial gyroscope sensor mounted on the upper sternum. The experiment was executed ten times according to the proposed experimental protocol. The output signals of the tri-axial accelerometer and the bi-axial gyroscope were measured during eight falls and eleven ADL action sequences. The threshold values of the signal vector magnitude (SVM_Acc), angular velocity (${\omega}_{res}$), and angular variation (${\theta}_{res}$) parameter were calculated using MATLAB. From the preliminary study, three thresholds (TH1, TH2, and TH3) were set so that the falls could be distinguished from ADL. When the parameter SVM_Acc is greater than 2.5 g (TH1), ${\omega}_{res}$ is greater than 1.75 rad/s (TH2), and ${\theta}_{res}$ is greater than 0.385 rad (TH3), these action sequences are recognized as falls. If at least one or more of these conditions is not satisfied, the sequence is classified as ADL.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.9
• /
• pp.1725-1730
• /
• 2017

The acceleration sensor and the gyroscopic sensor are used as representative sensors to detect repetitive motion and have been used to analyze various sporting components. However, both sensors have problems with noise sensitivity and accumulation of errors. There have been attempts to use two sensors together to overcome hardware problems. The complementary filter has shown successful results in mitigating the problems of both sensors by minimizing the disadvantages of accelerometer and gyroscope sensors and maximizing their advantages. In this paper, we proposed a modified method using neural network to reduce variable. The neural network is an algorithm that can precisely measure even in unexpected environments or situations by pre-learning the number of various cases. The proposed method applies a Neural Network by dividing the repetitive motion into three sections, the first, the middle and the end. As a result, the recognition rate is 96.35%, 98.77%, 96.92% and the accuracy is 97.18%.