• 대한기계학회논문집A
• /
• 제41권9호
• /
• pp.877-885
• /
• 2017

본 논문에서는 포신의 강선을 고려한 포 발사 해석기법을 다룬다. 포 발사 환경에서 탄두는 고충격 및 고회전의 동적 거동이 발생한다. 이러한 동적 거동에서 탄두 및 탄두 내 전자 장비가 손상되는 사례가 발생하고 있다. 따라서 포 발사 환경에서 탄두의 동적 거동 분석 및 생존성 평가를 위한 포 발사 해석기법의 개발이 필요한 실정이다. 본 논문에서는 앞서 선행연구자들의 단순화된 포 발사 해석기법을 개선하여, 포신의 강선과 탄대의 접촉에 따른 탄두의 회전을 구현할 수 있는 포 발사 해석기법을 개발하였다. 개발된 포 발사 해석기법은 실험결과와 비교를 통하여 검증하였으며, 제안된 해석기법을 이용하여 포 발사 시 탄두의 동적 거동 및 생존성을 평가하였다.

• 한국CDE학회논문집
• /
• 제19권4호
• /
• pp.340-346
• /
• 2014

There are many factors that contribute to hit probability of the gun shot of ground combat vehicles. Aiming accuracy is mainly affected by the dynamic state of the vehicle. The stabilization error of the turret under system vibration is one of the major factors that affect the aiming accuracy. The vibration of the vehicle is affected by both the state of the road and the speed of the vehicle. This paper analyzes the aiming accuracy of the gun equipped on the GCV when the vehicle drives on the different roads and at different speed. The vertical displacement and the pitch angle of the gun are calculated and the impact points of the target are calculated. Distribution of the impact points on the target is greatly influenced by the pitch rotation rather than vertical displacement. And this aiming errors result in the errors of point of impacts on the target after the bullet flies through the air under trajectory equations. The GCV is modeled using a half-car model with 6 D.O.F. and the specifications of the M2 machine gun are used in trajectory calculation simulation and the target is located in 1000 m away from the gun.

• 대한기계학회논문집B
• /
• 제27권4호
• /
• pp.466-475
• /
• 2003

The gun-type gas burner adopted in this study is generally composed of eight slits and swirl vanes. Thus, this paper is studied to investigate the effect of slits and swirl vanes on the turbulent flow fields in the horizontal plane of gas swirl burner with a cone type baffle plate measured by using X-probe from hot-wire anemometer system. This experiment is carried out at flow rate 450 $\ell$/min in the test section of subsonic wind tunnel. The axial mean velocity component in the case of burner model with only swirl vanes shows the characteristic that spreads more remarkably toward the radial direction than axial one, it does, however, directly opposite tendency in the case of burner model with only slits. Consequently. both slits and swirl vanes composing of gun-type gas burner play an important role in decrease of the speed near slits and increase of the flow speed in the central part of a burner because the biggest speed spurted from slits encircles rotational flow by swirl vanes and it drives main flow toward the axial direction. Moreover, the turbulent intensities and turbulent kinetic energy of gun-type gas burner are distributed with a fairly bigger size within X/R<0.6410 than burner models which have only slits or swirl vanes because the rotational flow by swirl vanes and the fast jet flow by slits increase flow mixing, diffusion, and mean velocity gradient effectively.

• 전기학회논문지P
• /
• 제59권4호
• /
• pp.440-443
• /
• 2010

This paper deals with the method of vibration measurement of a gun barrel structure using mechanical filter. When a bullet with high speed is moving within a gun barrel type structure with low bending vibration frequencies, it is difficult to measure the bending vibration signals of the structure. For example, noncontact type sensors such as displacement or velocity sensor are not appropriate for the measurement of vibrational signals because of the movement effect of the equipment frame through the moving structures or effect of the ground vibration. One of contact type sensors such as accelerometer is profitable for measurement of vibrational signals because of its wide measurement ranges. In the case of a gun barrel structure including high vibrational signals like shock waves, however, it is necessary to propose vibration measurement method filtering high frequencies. The purpose of the paper is to propose the proper vibrational measurement technique filtering high frequencies of a gun barrel type structure.

• 한국자기학회지
• /
• 제2권1호
• /
• pp.69-74
• /
• 1992

본 논문에서는 커패시터로 구동되는 공진 유도형 코일건의 속도 및 에너지 전달 특성을 해석했다. 유도형 코일건은 설치가 자유롭고, 기계적 마모가 적고, 반복사용이 가능하며, 전달되는 힘이 피투사체의 표면에 고르게 분포한다는 장점을 가지고 있다. 특성해석을 위해 등가회로를 구성 하여 회로방정식과 운동방정식을 유도하고, 이 방정식들을 Runge-Kutta 방법을 사용하여 수치적으 로 풀었다. 그리고 구동회로의 공진주파수 및 커패시터의 충전전압에 대한 에너지 전달율을 구했으 며, 또한 피투사체의 초기위치와 도전율, 구동회로의 점호각, 충전전압 및 구동코일의 저항 각각에 대한 피투사체의 포구속도의 변화를 구하였다.

• 한국기계가공학회지
• /
• 제17권2호
• /
• pp.118-123
• /
• 2018

Coil guns are known worldwide as inexpensive space launch vehicles. The principle of Fleming's right-hand rule allows the coil gun to accelerate the projectile by applying enormous voltage to the solenoid coil. This study was performed to improve the speed of the coil gun using MATLAB, a commercially available numerical program for high launching force of electromagnetic projectiles. To maximize the speed of the projectile, the largest coil of American wire gauge was used, and the number of windings in the radial and axial directions of the solenoid coil was optimized. Optimal length of the projectile was obtained by calculating the optimal aspect ratio between the axial length of the solenoid coil and the length of the projectile.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집 특별세미나,특별/일반세션
• /
• pp.517-524
• /
• 2009

This paper proposes a magnetic analysis model and design method of transformer for the high-speed EMU. It has a many part of the consideration in design because the transformer in high-speed train has the multiple output. Also the output characteristic, weight, and size of transformer is an important factor. This research proposes a design method of transformer in high-speed EMU. And it is easy to design by using the analysis model in design the transformer through the establishment of the magnetic analysis model.

• 전자공학회논문지 IE
• /
• 제43권4호
• /
• pp.83-92
• /
• 2006

EMC를 정량 Moulding 후 잔량 처리와 작동 시 역 차단 방식의 설계하여 기계적 동작에 의해 흡입이 일어나도록 하여 Needle Tip의 잔량과 사인 현상을 해결하였다. 본 논문에서는 Gun과 세척제 Tank를 직결하도록 설계하여 세척이 용이하며, 원하는 량을 미리 계량하여 정밀 정량을 고속으로 EMC를 Molding 할 수 있도록 개발하기 때문에 반도체 Packaging 공정에 필수적인 장비라고 사료된다.

• 한국소음진동공학회논문집
• /
• 제25권9호
• /
• pp.593-598
• /
• 2015

In this paper, the silencer for large caliber gun to reduce the propagation of gun-generated noise was studied. The results of structural analysis and firing test were described. Structural analysis was conducted by using a commercial program, ANSYS, and showed that there was not any structural problem. The sound pressure level was diminished about 10 dB by the silencer adapted in front of the gun and the soundness of the material was verified from the internal pressure measurement. The reduction of weight, improvement of durability and speed-up of actuating device have to be studied later to improve the usability of silencer for large caliber gun.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.777-778
• /
• 2010