• Korean Journal of Materials Research
• /
• v.19 no.11
• /
• pp.588-595
• /
• 2009

The knowledge of grain growth of carbide particles is very important for manufacturing micrograined cemented carbides. In the present study, continuous and discontinuous grain growth in WC-Co and WC-VC-Co cemented carbides is investigated using the Monte Carlo computer simulation technique. The Ostwald ripening process (solution/re-precipitation) and the grain boundary migration process are assumed in the simulation as the grain growth mechanism. The effects of liquid phase fraction, grain boundary energy and implanted coarse grain are examined. At higher liquid phase content, mass transfer via solid/liquid interfaces plays a major role in grain growth. Growth rate of the implanted grain was higher than that of the matrix grains through solution/re-precipitation and coalescence with neighboring grains. The results of these simulations qualitatively agree with experimental ones and suggest that distribution of liquid phase and carbide particle/carbide grain boundary energy as well as contamination by coarse grain are important factors controlling discontinuous grain growth in WC-Co and WC-VC-Co cemented carbides. The contamination by coarse grains must by avoided in the manufacturing process of fine grain cemented carbides, especially with low Co.

• Korean Journal of Crystallography
• /
• v.6 no.2
• /
• pp.141-157
• /
• 1995

Single crystals of TeO2 with large diameter were grown by Czochralski technique with auto-diameter control system. The ratio of crystal to crucible was 60-70%. The effect of critical pulling and rotation rate on the crystal quality was studied. Optimum growth parameters for high quality crystal pulling rate was less than 1.2 mm/hr. The solid-liquid interface was convex at the rotation rate of 10-23 rpm and concave at the rotation rate of more than 25 rpm, depending on the size of crystal and crucible. The platinum concentration in the melts is one of the main factors of the constitutional supercooling and thus the bubble entrapment in the growing crystal. Growth axis was confirmed to {110} direction during the whole growth procedure. Infrared spectrometric study and dislocation density measurment by chemical etching method on the grown crystal were performed. Finally, the reasons of cooperation of striations, inclusions, and optical inhomogeneities were discussed.

• Journal of Electrochemical Science and Technology
• /
• v.14 no.1
• /
• pp.85-95
• /
• 2023

In recent years, solid-state Li metal batteries (SSLBs) have attracted significant attention as the next-generation batteries with high energy and power densities. However, uncontrolled dendrite growth and the resulting pulverization of Li during repeated plating/stripping processes must be addressed for practical applications. Herein, we report a plastic-crystal-based polymer/ceramic composite solid electrolyte (PCCE) to resolve these issues. To fabricate the one-side ceramic-incorporated PCCE (CI-PCCE) film, a mixed precursor solution comprising plastic-crystal-based polymer (succinonitrile, SN) with garnet-structured ceramic (Li₇La₃Zr₂O₁₂, LLZO) particles was infused into a thin cellulose membrane, which was used as a mechanical framework, and subsequently solidified by using UV-irradiation. The CI-PCCE exhibited good flexibility and a high room-temperature ionic conductivity of over 10^-3 S cm^-1. The Li symmetric cell assembled with CI-PCCE provided enhanced durability against Li dendrite penetration through the solid electrolyte (SE) layer than those with LLZO-free PCCEs and exhibited long-term cycling stability (over 200 h) for Li plating/stripping. The enhanced Li⁺ transference number and lower interfacial resistance of CI-PCCE indicate that the ceramic-polymer composite layer in contact with the Li anode enabled the uniform distribution of Li⁺ flux at the interface between the Li metal and CI-PCCE, thereby promoting uniform Li plating/stripping. Consequently, the Li//LiFePO₄ (LFP) full cell constructed with CI-PCCE demonstrated superior rate capability (~120 mAh g^-1 at 2 C) and stable cycle performance (80% after 100 cycles) than those with ceramic-free PCCE.

• Journal of Ginseng Research
• /
• v.4 no.2
• /
• pp.175-185
• /
• 1980

A study was made to clarify the topographical. and Physical characteristics of ginseng field in terms of soil science and to find the relationship between soil characteristics and ginseng growth, as well as yield of ginseng roots Forty nine farmer's red ginseng field of ginseng growing area were chosen for this study and investigated for two years. The results obtained were as follow. 1. Ginseng fie1ds with high yield which represent the more than 1.8kg of ginseng root per 3.2m2 were found in soil series of Bancheon, Yeongog, Weongog, etc. whose texture were the clay loam to clay soil. On the other hand, ginseng field with low yield were observed in soil series of seogto whose texture was loamy soil with high content of gravels. 2 Soil of ginseng field with high yield had higher content of clay. silt soil moisture and soil pore as compared with soils of low yields. These soil characteristics were positively correlated with stem length stem diameter and root weight of ginseng plsnt and negatively correlated with rate of missing plant 3. The adequate ranges of soil 3 phase from high yield ginseng field were 40 to 50% of solid Phase, 22 to 35% of liquid phase, 25 to 35% of gaseous phase in top soil and 45 to 55% of solid phase. 28 to 30% of liquid phase. 15 to 20% of gaseous phase in subsoil respectively.

• KSBB Journal
• /
• v.6 no.1
• /
• pp.1-7
• /
• 1991

To produce economically important indole alkaloids by cell cultures, we selected protoplastsderived clones (protoclones) of vinca (Catharanthus roseus) for high yields of catharanthine and ajmalicine. Protoplasts were enzymatically isolated from suspension-cultured cells. The highest plating efficiency (1%) was obtained when protoplasts were plated at a density of 1$\times$105 protoplasts/ml in a culture medium solidified with 0.4% Seaplaque agarose. The growth rates of 40 protoclones subcultured on a solid medium varied over a wide range. Protoclone VPC-6, which had the highest growth rate, was observed to produce relatively high yields of catharanthine and ajmalicine when cultured in a liquid medium. Although the original cell line did not produce catharanthine at a detectable level by HPLC, protoclone VPC-10 produced it at a level of 5.9$\mu\textrm{g}$/g fresh weight of cells for 10 days of culture. Under the same conditions, protoclone VPC-15 produced ajmalicine at a level of 133.6$\mu\textrm{g}$/g, of which productivity was improved about ,3 times than that of the original cell line. The results indicate that differences in the growth rate and indole alkaloid yield among the protoclones reflect the somaclonal variation in suspnsion-cultured cells.

• Fire Science and Engineering
• /
• v.34 no.4
• /
• pp.22-28
• /
• 2020

The heat release rate (HRR) of fire for solid combustibles, consisting of multi-materials, was measured using the ISO 9705 room corner test, and a computational analysis was conducted to simulate the fire using an HRR prediction model that was provided by a fire dynamics simulator (FDS). As the solid combustible consisted of multi-materials, a cinema chair composed primarily of PU foam, PP, and steel was employed. The method for predicting the HRR provided by the FDS can be categorized into a simple model and a pyrolysis model. Because each model was applied and computational analysis was conducted under the same conditions, the HRR and fire growth rate predicted by the pyrolysis model had good agreement with the results obtained using the ISO 9705 room corner test.

• KSBB Journal
• /
• v.25 no.2
• /
• pp.142-154
• /
• 2010

The protein-bound innerpolysaccharides (IPS) produced by suspended mycelial cultures of Inonotus obliquus have promising potentials as an effective antidiabetic as well as an immunostimulating agents. To enhance IPS production, intensive strain improvement process should be carried out using large amount of UV-mutated protoplasts. During the whole strain-screening process, the stage of solid growth-culture was found to be the most time-requiring step, thus preventing rapid screening of high-yielding producers. In order to reduce the cell growth period in the solid growth-stage, therefore, solid growth-medium was optimized using the statistical methods such as (i) Plackett-Burman and fractional factorial designs (FFD) for selecting positive medium components, and (ii) steepest ascent (SAM) and response surface (RSM) methods for determining optimum concentrations of the selected components. By adopting the medium composition recommended by the SAM experiment, significantly higher growth rate was obtained in the solid growth-cultures, as represented by about 41% larger diameter of the cell growth circle and higher mycelial density. Sequential optimization process performed using the RSM experiments finally recommended the medium composition as follows: glucose 25.61g/L, brown rice 12.53 g/L, soytone peptone 12.53 g/L, $MgSO_4$ 5.53 g/L, and agar 20 g/L. It should be noted that this composition was almost similar to the medium combinations determined by the SAM experiment, demonstrating that the SAM was very helpful in finding out the final optimum concentrations. Through the use of this optimized medium, the period for the solid growth-culture could be successfully reduced to about 8 days from the previous 15~20 days, thus enabling large and mass screening of high producers in a relatively short period.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.89-93
• /
• 1995

Effects of hydrogenation in amorphous silicon rile growths on Solid Phase Crystallization (SPC) was investigated using x-ray diffractometry, energy dispersive Spectroscopy, and Raman spectrum. Interdiffusion of barium(Ba) and aluminum(Al) compounds of corning substrate was observed in both of rf sputtering and LFCVD films under the low temperature(580$^{\circ}C$) annealing. Low degree of crystallinity resulted from the interdiffusion was obtained. Highly applicable degree of crystallinity was obtained through the mechanical damage induced surface activation on amorphous silicon films. X-ray diffraction intensity of (111) orientation was used to characterize the degree of crystallinity of SPC. Nucleation and growth rate in SPC could be controllable through the employed surface treatment. IIydrogenated LPCVD films showed the superior crystallinity to non-hydrogenated sputtering films. Insignificant effects of activation treatment in sputtered film was of activation treatment in sputtered film was observed on SPC.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.1
• /
• pp.1-11
• /
• 2000

This study investigates the problem of phase change from liquid to solid in the inviscid stagnation flow. The solution of dimensionless governing equations is determined by the three dimensionless parameters of (temperature ratio/conductivity ratio), Stefan number, and diffusi-vity ratio. The solution at the initial stage of freezing is obtained by expanding it in powers of time, and the final equilibrium state is determined from the steady-state governing equations. The equilibrium state is dependent on (temperature ratio/conductivity ratio), but is independent of Stefan number and diffusivity ratio. The effect of fluid flow on the pure conduction problem can be clearly seen from the solution of the initial stage and the final equilibrium state, and the characteristics of the solidification process for all the dimensionless parameters are elucidated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.11 s.254
• /
• pp.1107-1116
• /
• 2006

The droplet ejection process driven by an evaporating bubble in a thermal inkjet printhead is investigated by numerically solving the conservation equations for mass, momentum and energy. The phase interfaces are tracked by a level set method which is modified to include the effect of phase change at the interface and extended for multiphase flows with irregular solid boundaries. The compressibility effect of a bubble is also included in the analysis to appropriately describe the bubble expansion behaviour associated with the high pressure caused by bubble nucleation. The whole process of bubble growth and collapse as well as droplet ejection during thermal inkjet printing is simulated without employing a simplified semi-empirical bubble growth model. Based on the numerical results, the jet breaking and droplet formation behaviour is observed to depend strongly on the bubble growth and collapse pattern. Also, the effects of liquid viscosity, surface tension and nozzle geometry are quantified from the calculated bubble growth rate and ink droplet ejection distance.