• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.3
• /
• pp.355-361
• /
• 1987

Creep and fatigue tests were carried out on crack growth properties of small surface cracks in 304 stainless steel at 538.deg.C, 593.deg. C and 650.deg. C in air, by using small plate specimens with a small artificial pit. All the data of the crack growth rate per hour obtained in the present tests were correlated with the maximum stress intensity factor, so that the applicability of linear fracture mechanics to the crack growth of surface cracks at elevated temperature was investigated. In the creep test, relatiion of .sigma.$\^$n/.t$\_$f/=C is obtained between failure time and nominal stress at each temperature level, where n has the value of 11-14 depending on the temperature level. In the creep and fatigue crack growth properties of surface cracks at the elevated temperatures, the maximum stress intensity factor, $_{4}$$\_$max/, is some extent applicable parameter to describe the surface crack growth rate under the present experimental conditions. The crack growth rate per hour increases when the holding time decreases, and creep crack growth rate per hour becomes the lowest limit of crack growth rate per hour in this tests.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.1
• /
• pp.62-69
• /
• 1986

Fatigue surface crack growth was studied in 7075-T651 aluminum alloy plates subjected largely to bending loads. The surface crack length and its depth were measurement by the unloading elastic compliance method. The surface crack growth rate dc/dN, on the surface and da/dN, in the depth direction were obtained by the secant method. The stress intensity factor range .DELTA.K was computed by means of Newman and Raju equation. The aspect ratio a/c was presented in form of a/c=0.815-0.853(a/T). The effect of the stress ratio on the stable surface crack growth rates under increasing .DELTA.T is larger in lower .DELTA.K, while the relation between dc/dN, da/dN and the effective stress intensity factor range .DELTA.K$_{eff}$ is weakly dependent on the stress ratio.o.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.9
• /
• pp.2843-2853
• /
• 1996

The multi-point procedure is developed to predict the shape change of a semi-elliptical surface crack during stable fatigue crack growth. 3-D stress intensity factors along a crack front are calculated using the simplified 3-D J-intergral. Crack growth rate coefficient in the Paris law is assumed to be constant along the crack growth. Crack growth rate is set to be the distance between the two parallel tangent lines on the two semi-elliptic crack fronts before and after crack growth.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.82-89
• /
• 2012

In order to clarify the effect of overload on crack growth behaviors, fatigue tests for overload were carried out for round plain specimens of SM45C steel. In the experiment, typical semi-elliptical crack shape was found and further crack growth behaviors were tested. Using three types of single overload fatigue tests, Crack growth retardation phenomenon were examined. The growth rate of surface crack(da/dN) during retardation period was analyzed in terms of ${\Delta}K$ and ${\Delta}K_{eff}$. On the growth rate of surface crack analyzed by ${\Delta}K$, the dependence of overload stress levels appears. However, on the growth rate by ${\Delta}K_{eff}$ obtained by Willenborg analysis, there is a liner relationship between da/dN and ${\Delta}K_{eff}$ with narrow scatter band.

• Journal of the Korean Ceramic Society
• /
• v.33 no.9
• /
• pp.985-994
• /
• 1996

The initiation and growth of $\alpha$-Al2O3/metal composites by the directed oxidation of molten commercial AlZnMg-alloy at 1223-1423K were investigated. Spontaneous bulk growth did not occur on the alloy alone. but the uniform initiation and growth of the composite were obtained by putting a thin layer of SiO2 particles on the surface of the alloy. Without SiO2 the external surface of the oxide layer was convered by MgO and MgAl2O4. But with the SiO2 reaction initiate the porous ZnO layers were found on the growth surface. The higher process temperature yielded a lower metal content. The oxidation product of $\alpha$-Al2O3 was found to be oriented with c-axis parallel to th growth direction. The growth rates increased with temperature and the apparent activation energy was 111.8 kJ/mol.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.2
• /
• pp.191-197
• /
• 1987

It has been well known that the fracture mechanics can be applied to large through crack growth. But the growth rate of small surface cracks initiated from a small defect under rotary bending fatigue tests can not be treated as a function of stress intensity factor range. In this paper, to investigate the growth behavior of surface small fatigue cracks in the view-point of both fracture mechanics and strength of materials, the fatigue test has been carried out on two kinds of plain carbon steels with a small surface defect. Applying the concept of the cyclic strain intensity factor range .DELTA. $K_{\epsilon}$/$_{t}$ to the analysis of small surface fatigue crack growth, it is found that the relationship between cyclic strain intensity factor range and crack growth rate shows linear relation on logarithmic coordinates regardless of defect sizes and two kinds of carbon steels.s.s.

• Journal of the Korean institute of surface engineering
• /
• v.24 no.1
• /
• pp.1-17
• /
• 1991

Understanding of the detailed reaction mechanisms during MOVPE and ALE is essential to further improve the properties of the grown crystals and the controllability of the growth parameters. The unified models for the detailed reaction paths are not available at this stage. The study, however, has been advanced to the extent that consensus on some of the reaction paths can be drawn from the scattered data. Metalakyls such as TMGa and TMIn seem to nearly fully decompose in the gas phase through homogeneous reaction at the typical MOVPE growth temperature. Hydrides such as AsH3 and PH3, on the contrary. seem to decompose heterogeneously onthe substrate surfaces as well as homogeneously in the gas phase. However, at lower temperatures, where ALE crystals are typically grown, the growth process is strongly dependent on the surface reactions. It seems that steric hindrance effects which the radicals reaching the substrate exhibit on the surface the growth rate a function of the metalalkyle supply durations. In addition, dydrogens released from hydrides seem to play an essential role in removing carbons leberated from the metalalkyls. High growth temperatures also seem to be effective in desorbing carbons from surface. The understanding of the reaction mechanisms was possible though diverse appraaches utilizing many ex-situ and in-situ diagnostic techniques and genuine experimental designs. It is the purpose of this paper to review and discuss many of these efforts and to draw some possible conclusions from them.

• Journal of the Korean institute of surface engineering
• /
• v.24 no.1
• /
• pp.1.1-1.1
• /
• 1991

Understanding of the detailed reaction mechanisms during MOVPE and ALE is essential to further improve the properties of the grown crystals and the controllability of the growth parameters. The unified models for the detailed reaction paths are not available at this stage. The study, however, has been advanced to the extent that consensus on some of the reaction paths can be drawn from the scattered data. Metalakyls such as TMGa and TMIn seem to nearly fully decompose in the gas phase through homogeneous reaction at the typical MOVPE growth temperature. Hydrides such as AsH3 and PH3, on the contrary. seem to decompose heterogeneously onthe substrate surfaces as well as homogeneously in the gas phase. However, at lower temperatures, where ALE crystals are typically grown, the growth process is strongly dependent on the surface reactions. It seems that steric hindrance effects which the radicals reaching the substrate exhibit on the surface the growth rate a function of the metalalkyle supply durations. In addition, dydrogens released from hydrides seem to play an essential role in removing carbons leberated from the metalalkyls. High growth temperatures also seem to be effective in desorbing carbons from surface. The understanding of the reaction mechanisms was possible though diverse appraaches utilizing many ex-situ and in-situ diagnostic techniques and genuine experimental designs. It is the purpose of this paper to review and discuss many of these efforts and to draw some possible conclusions from them.

• Advances in nano research
• /
• v.14 no.6
• /
• pp.557-573
• /
• 2023

The rapid growth of zinc-oxide (ZnO) nanostructures (NSs) on woven carbon fiber (WCF) is reported in this study employing a microwave-aided chemical bath deposition process. The effects of different process parameters such as molar concentration, microwave duration and microwave power on morphologies and growth rate of the ZnO on WCF were studied. Furthermore, an attempt has been taken to study influence of different type of growth solutions on ZnO morphologies and growth rates. The surface functionalization of WCF fabrics is achieved by successful growth of crystalline ZnO on fiber surface in a very short duration through one-step microwave synthesis. The morphological, structural and compositional studies of ZnO-modified WCF are evaluated using field-emission scanning electron microscopy, X-ray diffraction and energy dispersive X-ray spectroscopy respectively. Good amount of zinc and oxygen has been seen in the surface of WCF. The presence of the wurtzite phase of ZnO having crystallite size 30-40 nm calculated using the Debye Scherrer method enhances the surface characteristics of WCF fabrics. The UV-VIS spectroscopy is used to investigate optical properties of ZnO-modified WCF samples by absorbance, transmittance and reflectance spectra. The variation of different parameters such as dielectric constants, optical conductivity, refractive index and extinction coefficient are examined that revealed the enhancement of optical characteristics of carbon fiber for wide applications in optoelectronic devices, carbon fiber composites and photonics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.133-141
• /
• 2002

This paper describes a versatile finite element technique which has been used to investigate wide range of structural defects of practical importance. The procedure automatically remeshes the three-dimensional finite element model during the stages of crack growth. Problems include the surface cracks in leak-before-break situations, the shape development of multiple surface defects.