• 전기전자학회논문지
• /
• 제15권1호
• /
• pp.49-56
• /
• 2011

본 논문에서는 고주파 발진회로의 공진기를 패치 안테나로 사용하는 능동발진 안테나를 2.4GHz 대역에서 제안하여 소형 무선도플러 센서로서 이동체의 거리나 속도 등을 측정할 수 있게 하였다. 이동체의 움직임은 고주파 발진 주파수의 천이를 발생시키며 이를 검출하는 회로를 통해 제안된 구조의 동작을 확인하였다. 설계 제작된 무선 도플러 센서는 직경이 30mm, 높이 4.2mm 정도로 매우 작은 원형디스크 형태를 갖으며, 안테나는 2.373GHz에서 약 130도의 빔폭과 전방향 방사특성을 나타내었다. 센서의 감도 측정결과, 1m 떨어져 움직이고 있는 도체판에 대해 최소 190mV의 도플러 신호 전압을 얻었고, 센서의 자유낙하 실험으로부터 지표상의 4.5m 지점에서 부터 지표면까지 전압크기가 선형적으로 증가하였다.

• 마이크로전자및패키징학회지
• /
• 제12권3호
• /
• pp.267-274
• /
• 2005

This paper presents the fabrication of surface acoustic wave (SAW)-based pressure sensor for long-term stable mechanical compression force measurement. SAW pressure sensor has many attractive features for practical pressure measurement: no battery requirement, wireless pressure detection especially at hazardous environments, and easy other functionality integrations such as temperature, humidity, and RFID. A $41^{\circ}$ YX $LiNbO_3$ piezoelectric substrate was used because of its high SAW propagation velocity and large values of electromechanical coupling factors $K^2$. A silicon substrate with $\~200{\mu}m$ deep cavity was bonded to the diaphragm with epoxy, in which gold was covered all over the inner cavity in order to confine electromagnetic energy inside the sensor, and provide good isolation of the device from its environment. The reflection coefficient $S_{11}$ was measured using network analyzer. High S/N ratio, sharp reflected peaks, and clear separation between the peaks were observed. As a mechanical compression force was applied to the diaphragm from top with extremely sharp object, the diaphragm was bended, resulting in the phase shifts of the reflected peaks. The phase shifts were modulated depending on the amount of applied mechanical compression force. The measured $S_{11}$ results showed a good agreement with simulated results obtained from equivalent admittance circuit modeling.

• 한국측량학회지
• /
• 제36권5호
• /
• pp.395-401
• /
• 2018

Recently, most of mobile devices are equipped with GNSS (Global Navigation Satellite System). When the GNSS signal is available, it is easy to obtain position information. However, GNSS is not suitable solution for indoor localization, since the signals are normally not reachable inside buildings. A wide varieties of technology have been developed as a solution for indoor localization such as Wi-Fi, beacons, and inertial sensor. With the increased sensor combinations in mobile devices, mobile devices also became feasible to provide a solution, which based on PDR (Pedestrian Dead Reckoning) method. In this study, we utilized the combination of three sensors equipped in mobile devices including accelerometer, digital compass, and gyroscope and applied three representative PDR methods. The proposed methods are done in three stages; step detection, step length estimation, and heading determination and the final indoor localization result was evaluated with terrestrial LiDAR (Light Detection And Ranging) data obtained in the same test site. By using terrestrial LiDAR data as reference ground truth for PDR in two differently designed experiments, the inaccuracy of PDR methods that could not be found by existing evaluation method could be revealed. The firstexperiment included extreme direction change and combined with similar pace size. Second experiment included smooth direction change and irregular step length. In using existing evaluation method which only checks traveled distance, The results of two experiments showed the mean percentage error of traveled distance estimation resulted from three different algorithms ranging from 0.028 % to 2.825% in the first experiment and 0.035% to 2.282% in second experiment, which makes it to be seen accurately estimated. However, by using the evaluation method utilizing terrestrial LiDAR data, the performance of PDR methods emerged to be inaccurate. In the firstexperiment, the RMSEs (Root Mean Square Errors) of x direction and y direction were 0.48 m and 0.41 m with combination of the best available algorithm. However, the RMSEs of x direction and y direction were 1.29 m and 3.13 m in the second experiment. The new evaluation result reveals that the PDR methods were not effective enough to find out exact pedestrian position information opposed to the result from existing evaluation method.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2001년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 2001
• /
• pp.36-43
• /
• 2001

In Korea, we are absolutely short of earthquake data in good quality from moderate and large earthquakes, which are needed fur the study of strong ground motion characteristics. This means that the best use of the available data is needed far the time being. In this respect, several methods are suggested in this paper, which can be applied in the process of data selection and analysis. First, it is shown that the calibration status of seismic stations can be easily checked by comparing the spectra from accelerometer and velocity sensor both of which are located at the same location. Secondly, it is recommended that S/N ratio in the frequency domain should be checked before discarding the data by only look of the data in time domain. Thirdly, the saturated earthquake data caused by ground motion level exceeding the detection limit of a seismograph are considered to see if such data can be used for spectrum analysis by performing numerical simulation. The result reveals that the saturated data can still be used within the dominant frequency range according to the levels of saturation. Finally, a technique to minimize the window effect that distorts the low frequency spectrum is suggested. This technique involves detrending in displacement domain once the displacement data are obtained by integration of low frequency components of the original data in time domain. Especially, the low frequency component can be separated by using discrete wavelet transform among many alternatives. All of these methods mentioned above may increase the available earthquake data and frequency range.

• 한국해양공학회지
• /
• 제21권4호
• /
• pp.55-60
• /
• 2007

In contrast to the method in Part I, which is considered to be the general approach, Part II pursues a closed-form solution. However, this closed-form solution is available only in the 2D situation under the assumption that the moving object is restricted to a 2D space, and also requires the use of only two laser-slit sensors. Since the motion of the container loaded on top of an AGV is restricted to a plane parallel to the ground, it can be considered a 2D motion. As a simple method, but with a high cost, the use of a laser scanner is also discussed. Since the approach in Part I already uses three laser-slit sensors, it is desirable to use the schemes presented in Part II for supplementary purposes.

• 한국측량학회지
• /
• 제37권2호
• /
• pp.55-62
• /
• 2019

The stereo geometry establishment based on the precise sensor modeling is prerequisite for accurate stereo data processing. Ground control points are generally required for the accurate sensor modeling though it is not possible over the area where the accessibility is limited or reference data is not available. For the areas, the relative orientation should be carried out to improve the geometric consistency between the stereo data though it does not improve the absolute positional accuracy. The relative orientation requires conjugate points that are well distributed over the entire image region. Therefore the automatic conjugate point extraction is required because the manual operation is labor-intensive. In this study, we applied the method consisting of the key point extraction, the search space minimization based on the epipolar line, and the rigorous outlier detection based on the RPCs (Rational Polynomial Coefficients) bias compensation modeling. We tested different parameters of window sizes for Kompsat-2 across track stereo data and analyzed the RPCs precision after the bias compensation for the cases whether the epipolar line information is used or not. The experimental results showed that matching outliers were inevitable for the different matching parameterization but they were successfully detected and removed with the rigorous method for sub-pixel level of stereo RPCs precision.

• 한국측량학회지
• /
• 제26권5호
• /
• pp.455-463
• /
• 2008

광학센서를 이용한 자료취득과정 중 발생하는 그림자는 영상내 동일 지물에 대한 밝기값의 지속성을 훼손하여 영상에 의한 지상 정보를 해석함에 있어 방해요소로 작용한다. 본 연구에서는 영상정보의 활용에 있어 그림자 영역을 추출하고 그림자에 의한 영상 왜곡을 제거하기 위한 기법에 관한 연구로써 자료원이 다른 보조자료의 활용을 배제하고 단일 컬러 영상으로부터 도심지의 지상 객체에 의한 그림자를 제거하기 위하여 HSI 컬러모델의 명도(intensity) 정보를 이용하여 그림자 영역을 추출하였으며 퓨리어 변환에 의한 그림자 영역 복원기법을 적용함으로써 영상에서의 그림자 영향을 제거하였다.

• 전기학회논문지
• /
• 제62권7호
• /
• pp.950-955
• /
• 2013

This paper proposes a new low-cost current detection method to implement vector-controlled inverter of 3-phase induction motor or permanent-magnet synchronous motor using 2 shunt resistors instead of expensive Hall current sensors. The proposed method can detect perfect phase currents without current-immeasurable area in all operating conditions of motor. This method uses 2 shunt resistors in Hall current sensor positions conventionally used to detect phase currents. Therefore, it requires accurate analog differential amplifiers to detect voltages across shunt resistors at high electric potential to ground. We show the good solutions which are implemented by voltage-divider resistors networks and the instrumentation amplifiers using several Op Amps at cheap price. Computer simulations and experiments were performed to confirm the effectiveness of proposed method. These results show that proposed method can perfectly detect phase currents without current-immeasurable area in all operating conditions of motor.

• 한국군사과학기술학회지
• /
• 제21권2호
• /
• pp.141-146
• /
• 2018

The Ground Moving Target Indication(GMTI) technique can detect the moving targets on land using its Doppler returns. Also, the GMTI system can work in night regardless of the weather condition because it is an active sensor that uses the electromagnetic waves as its source. In order to develop the GMTI system, Constant False Alarm Rate(CFAR) threshold optimization is important because the main performances like detection probability, false alarm rate and Minimum Detectable Velocity(MDV) are related deeply with CFAR threshold. These key variables are used to calculate CFAR threshold and then trade-off between the variables is performed. In this paper, CFAR threshold optimization procedures are introduced, and the optimization results are demonstrated.

• Journal of Information Processing Systems
• /
• 제15권5호
• /
• pp.1131-1140
• /
• 2019

Characteristics of fruit tree canopies are important target information for adjusting the pesticide application rate in variable rate spraying in orchards. Therefore, the target detection of the canopy characteristics is very important. In this study, a canopy volume measurement method for peach trees was presented and a variable rate spraying system based on canopy volume measurement was developed using the ultrasonic sensing, one of the most effective target detection method. Ten ultrasonic sensors and two flow control units were mounted on the orchard air-assisted sprayer. The ultrasonic sensors were used to detect the canopy diameters and the flow controls were used to modify the flow rate of the nozzles in real time. Two treatments were established: a constant application rate of $300Lha^{-1}$ was set as the control treatment for the comparison with the variable rate application at a $0.095Lm^{-3}$ canopy. The tracer deposition at different parts of peach trees and the tracer losses to the ground (between rows and within rows) were analyzed in detail under constant rate and variable rate application. The results showed that there were no significant differences between two treatments in the liquid distribution and the capability to reach the inner parts of the crop canopies.