• Korean Journal of Optics and Photonics
• /
• v.12 no.1
• /
• pp.17-24
• /
• 2001

Two-dimensional binary-phase diffraction gratings which can be employed to fabricate two- and three-dimensional periodic structures are designed and analyzed using rigorous coupled-wave analysis. These gratings serve as phase-masks which generate several diffracted waves from a normally incident beam and thus can produce a periodic interference pattern in space via nearfield holography. The properties of the diffracted beams can be controlled by varying the polarization and wavelength of the incident beam, surface-profile, groove depth and duty cycle of the mask. For the two-dimensional structure, optimum results can be obtained when the diffraction efficiency of the zero-order beam is minimized while that of the first-order maximized. On the other hand, when the diffraction efficiency of the zero-order is appreciable or even greater than other orders, we can obtain a variety of three-dimensional interference patterns which may be used to fabricate photonic crystals of tetragonal-body-centered and hexagonal structures in a submicron scale. scale.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.4 s.181
• /
• pp.153-161
• /
• 2006

Micro-forming is a suited technology to manufacture very small metallic parts(several $mm{\sim}{\mu}m$). Micro-forming of $Zr_{62}Cu_{17}Ni_{13}Al_8$ bulk metallic glass(BMG) as a candidate material for this developing process are feasible at a relatively low stress in the supercooled liquid state without any crystallization during hot deformation. In this study, micro- formability of a representative bulk metallic glass, $Zr_{62}Cu_{17}Ni_{13}Al_8$. was investigated for micro-forging of U-shape pattern. Micro-formability was estimated by comparing $R_f$ values ($=A_f/A_g$), where $A_g$ is cross-sectional area of U groove, and $A_f$ the filled area by material. Micro-forging process was simulated and analyzed by applying finite element method. FEM simulation results showed reasonable agreement with the experimental results when the material properties and simulation conditions such as top die speed, remeshing criteria and boundary conditions were tightly controlled. The micro-formability of $Zr_{62}Cu_{17}Ni_{13}Al_8$ was increased with increasing load and time in the temperature range of the supercooled liquid state. Also, FEM simulation using a commercial software, DEFORM was confirmed to be applicable for the optimization of micro-forming process.

• The Journal of Korean Physical Therapy
• /
• v.5 no.1
• /
• pp.109-114
• /
• 1993

The originator of the proprioceptive neuromuscular facilitation method was Dr. Herman Kabat, a man who received the bachelor of science degree from New York University in 1932. In 1936 he moved to the University of Minnesota where he served as instructor in physiology and also studies medicine. He received his medical doctorate in 1942. When Dr. Karbat meet Sister Kenny suggested that certain change. She does not receptive his ideas. So that he decided to pursure the treatment of patients. Upon the establishment of the Karbat- kaiser Institute to be opened in 1946. Margaret Knott, the first physical therapist to be employed by him and to become his head physical therapist. In 1948 Vallejo center was opened. Dr. Kabat developed the PNF method combined motions to ascertain the effectiveness of maximal resistance and stretch in facilitating the response of a weak distal muscle. He identified mass movement patterns that were spiral and diagonal in character in 1965. Margaret Knott presented lecture at tile APTA Annual Conference in Las Vegas. The title was In the groove. On December 18, 1978 she passed away at her home in Vallejo. Marie-Louise Mangold is director of the Kaiser Foundation Rehabilitation Center now. She is the Vice President of International Proprioceptive Neuromuscular facilitation Association. About 20 physical therapist working teaching and study at KFRC in Vallejo. PNF neuromuscular mechanism becomes integrated and efficient without awareness of individual muscle action, reflex and a multitude of other neurophysiological reactions. The principles of PNF are visual consideration, verbal consideration, and proprioceptive input consideration with tactile stimulation, joint receptors, appropriate facilitation, stretch reflex normal timing, irradiation, pattern of movement.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.1054-1060
• /
• 2002

In this paper, a new parallel-coupled-line microstrip BPF(BandPass Filter) improving the suppression performance of 2nd harmonic signals is studied. Using the consecutive pattern in coupled-line, the desired passband performance is improved and harmonic passband signal is rejected. Recalculation of classical filter design parameters(space-gap between lines, line widths and lengths) is not required. That is, after using the classical design methodology for parellel-coupled-line BPF, new filters can be easily realized by inserting periodic patterns in coupled-line. To investigate the validity of this novel technique, order-3 Butterworth BPF centered at 2.5 GHz with a 10 % FBW(Fractional Bandwidth) and order-5 Chebyshev BPF centered at 10 GHz with a 15 % FBW were used. When five and three square grooves are used, over 30 dB harmonic suppression at 2nd harmonic is achieved in simulation and experiment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.589-592
• /
• 2005

Micro-forming is a suited technology to manufacture very small metallic parts(several $mm{\sim}{\mu}m$). Micro-forming of $Zr_{62}Cu_{17}Ni_{13}Al_8$ bulk metallic glass(BMG) as a candidate material for this developing process are feasible at a relatively low stress in the supercooled liquid state without any crystallization during hot deformation. In this study, micro-formability of a representative bulk metallic glass, $Zr_{62}Cu_{17}Ni_{13}Al_8$, was investigated for micro-forging of U-shape pattern. Micro-formability was estimated by comparing $R_f$ values $(=A_f/A_g)$, where Ag is cross-sectional area of U groove, and $A_f$ the filled area by material. Microforging process was simulated and analyzed by applying finite element method. FEM simulation results should reasonable agreement with the experimental results when the material properties and simulation conditions such as top die speed, remeshing criteria and boundary conditions tightly controlled. The micro-formability of $Zr_{62}Cu_{17}Ni_{13}Al_8$ was increased with increasing load and time in the temperature range of the supercooled liquid state. Also, FEM Simulation using DEFORM was confirmed to be applicable for the micro-forming process simulation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.1
• /
• pp.100-106
• /
• 2020

In this paper smart shoes for dementia care using embedded boards and Low Power Wide Area technology and their application software are implemented. The communication board composed of Cortex-M3 board and LoRa module is embedded into groove made in outsole of smart shoes. Including the mold, the shoe outsole was manufactured by hand. By using application software and embedded board, caregiver can track the position of dementia patient using GPS and LoRa network. The location tracking and data transmission operations of smart shoes have been successfully verified in the outdoor environment. The smart shoes of this paper are applicable to a safety device to prevent the disappearance of demented patients through results of experiments and if bigdata is collected and analyzed by deep-learning, it may be helpful to analyze the predictive path of dementia patients or the pattern of dementia.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.7
• /
• pp.33-40
• /
• 2021

Current industrial flow is directed toward reducing the usage of raw materials by reusing parts, which is referred to as a circular economy (CE). Repair is one of the most value-added approaches in CE, which can be efficiently accomplished via additive manufacturing. The repair technology of metallic parts via the directed energy deposition process, which includes the selective removal and redeposition of damaged regions of metallic parts. Residual stress characteristics depend on the shape of the part and the shape of the redeposition region. The objective of this study is to investigate the effects of the radius and corner position of the substrate on the residual stresses for repair by using finite element analysis (FEA). The residual stress distribution of the 45° angle groove at the edge of the circular shape models on the outer and inner radii was analytically investigated. The analysis was accomplished using SYSWELD software by applying a moving heat source with defined material properties and cooling conditions integrated into the FEA model. The results showed a similar pattern of concentrated stress distribution for all models except the 40-mm and 60-mm radii, for which the maximum stress locations were different. The maximum residual stresses are high but lower than the yield strength, suggesting the absence of cracks and fractures due to residual stresses.

• Korean Journal of Veterinary Research
• /
• v.47 no.1
• /
• pp.7-17
• /
• 2007

The left main descending artery (LMDA) of left coronary artery (LCA) in rats runs around the left side of conus arteriosus after arising from the aortic sinus and descends to the apex of heart with branching several branches into the wall of left ventricle (LV). The ligation site of LMDA for myocardial infarction (MI) is the 2~4 mm from LCA origin, between the pulmonary trunk and left auricle. The characteristics that rat heart has no interventricular groove on the surface and its coronary arteries run intramyocardially with branching several branches give the difficulty in surgery for MI which resulted in expected size. This study was aimed to elucidate the branching patterns of the left coronary artery for analysis of MI size and for giving the basic data to producing small MI intentionally in 2 male species that are widely used, Sprague-Dowley (SD) and Wistar-Kyoto (WKY), in the world. Red latex casting was followed by the microdissection in 27 and 28 hearts of SD and WKY male rats, respectively. The branching patterns of LMDA were classified into 3 major types and others based on the left ventricular branches (L). The Type I, Type II, Type III and others are shown in 55.6%, 22.2%, 14.8%, and 7.4% in SD, 60.7%, 10.7%, 7.1%, and 21.5% in WKY, respectively. The branching number of the first left ventricular branch (L1) that are distribute the upper one third of LV was 1.2~1.5, and its branching sites were ranging 0.9~2.1 ᒠfrom LCA origin. L2, the second left ventricular branch distributing middle one third of LV, was the number of 1.2~1.4 and branching out ranging 5.1~5.7 mm. L3, the third left ventricular branch of LMDA distributing lower one third of LV, was the number of 1~1.5 and branching out ranging 7.0~9.3 mm from LCA origin. The common branch of L1 and L2 was branched from LMDA with the number of 1.1, and its site was located in the distance of mean of 1.5 mm and 2.8 mm in SD and WKY, respectively. The common branch of L2 and L3 was branched from LMDA with the number of 1, and its site was located in the distance of mean of 7.2 mm and 2.9 mm in SD and WKY, respectively. The right ventricular branches (R) of LMDA were short and branched in irregularly compared with L. The number of 1~4 of R were branched from LMDA. With regarding to the distribution area of L and the ligation site for MI, moderate MI (25~35% of LV) might be resulted in 70.4% and 60.7% in SD and WKY rats. Small MI might be produced intentionally if the ligation would be located at the 4~6 mm from LCA origin in the left side of LMDA. These data wold be helpful to expect the size of MI and to reproduce of small MI, intentionally, in rat hearts.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.44 no.3
• /
• pp.259-266
• /
• 2018

In today's society, where people look younger than their chronological age due to improvements in the quality of life, there is a gaining interest in anti-aging and how people compare to those in the same age group. We evaluated the wrinkle index, which is the most important attribute amongst skin parameters, to evaluate external age (wrinkle age). The wrinkles of the whole face were scored by divided 8 areas (forehead, glabella, nasal root, upper eyelid, lower eyelid, crow's feet, nasolabial groove and perioral skin) and analyzed the correlation between chronological age and skin parameters. 206 subjects (Korean female, n = 105 and Mongolians female, n = 101) were enrolled. Subjects were divided into four groups by ages: 20s, 30s, 40s, and 50s. Wrinkle scores of 8 areas were evaluated and developed a calculation formula based on the wrinkle scores. Skin characteristic parameters were measured about skin elasticity, pore, wrinkle, sebum secretion. There was no difference between the calculated ages and the chronological ages in Korean women. On the other hand, Mongolian looked older than chronological age by 9 years. The correlation between the facial wrinkle ages and skin physiology parameters was presented in the order of skin elasticity > pore or crow's feet > skin tone > sebum secretion in both countries. Skin elasticity represented the most related parameter with the facial wrinkle ages. This study identified the skin wrinkle patterns of Korean and Mongolian women and the wrinkle age calculation formula developed from this study can be used as a tool for calculating the facial wrinkle ages in cosmetic studies.

• Radiation Oncology Journal
• /
• v.14 no.1
• /
• pp.77-85
• /
• 1996

Purpose : Multileaf collimator(MLC) is very suitable tool for conformal radio-therapy and commissioning measurements for a multileaf collimator installed on a dual energy accelerator with 6 and 10MV photons are required, For modeling the collimator with treament planning software, detailed dosimetric characterization of the multileaf collimator including the penumbra width, leaf transmission between leaf leakage and localization of the leaf ends and sides is an essential requirement. materials and Methods : Measurement of characteristic data of the MLC with 26 pair block leaves installed on CLINAC 2100C linear accelerator was performed. Low sensitive radiographic film(X-omatV) was used for the penumbra measurement and separate experiments using radiographic film and thermoluminescent dosimeters were performed to verify the dose distribution, Measured films were analized with a photodensitometer of WP700i scanner. Results : For 6 & 10 MV x-ray energies, approximately $2.0\%$ of photons incident on the multileaf collimator were transmitted and an additional $0.5\%$ leakage occurs between the leaves. Localizing the physical end of the leaves showed less than 1mm deviation from the $50\%$ decrement line and this difference is attributed to the curved shaped end on the leaves One side of a sin히e leaf corresponded to the $50\%$ decrement line, but the opposite face was aligned with a lower value. This difference is due to the tongue and groove used to decrease between leaf leakage. Alignment of the leaves to form a straight edge resulted larger penumbra at far position from isocenter as compare with divergent alloy blocks. When the MLC edge is stepped by sloping field, the isodose lines follow the leaf pattern and Produce scalloping isodose curves in tissue. The effective penumbra by 45 degree stepped MLC is about 10mm at 10cm depth for 6MV x-ray. The difference of effective penumbra in deep tissue between MLC and divergent alloy blocks is small (5mm). Conclusion : Using the characteristic data of MLC, the MLC has the clinlical acceptability and suitability for 3-D conformal radiotherapy except small field size.