• 자원리싸이클링
• /
• 제33권2호
• /
• pp.37-45
• /
• 2024

몰리브덴은 높은 내열성, 내부식성에 의해 다양한 산업에 적용되어, 우리나라의 핵심광물로 선정된 중요한 금속이다. 그러나 최근 몰리브덴 광맥의 저품위화로 인해 생산에 어려움을 겪고 있어, 몰리브덴 선광 공정에 대한 효율 향상이 필요하다. 본 연구에서는 국내 몰리브덴광 선광 공정의 효율 향상을 위한 기초 선광 특성 평가 연구를 수행하였다. 기초 선광 특성은 광물학적 분석, 분쇄일지수, 부유선별 속도 분석으로 평가되었다. 분석 결과, 단체분리가 가능한 몰리브덴광의 입자 크기는 ~100 ㎛였으며, 분쇄 일지수는 14.57 kWh/t로 산출되었다. 또한 부유선별 속도 분석을 통해, 부유선별 단위 공정 각각의 최적 부유선별 시간을 제공함으로써 최적화를 위한 운영 조건을 확립하였다. 마지막으로 본 연구에서 제공한 몰리브덴광 기초 선광 특성 정보는 향후 산업 규모의 몰리브덴 선광 플랜트의 분쇄 및 부유선별 공정을 진단하는 데 활용될 예정이다.

• 펄프종이기술
• /
• 제47권4호
• /
• pp.5-12
• /
• 2015

In recent years, it had focused on the improvement of paper properties by addition of NFC (Nano-fibrillated Cellulose). Although the addition of NFC to wet-end of papermaking process could be suggested as a new solution to improve the strength properties of paper, it was not possible to avoid the bad drainage caused by the added NFC's chocking pores of wet web. Instead of the direct addition to wet-end, spraying of NFC to web in wire-section was tried in this study and evaluated by checking various paper properties including surface smoothness, tensile strength, folding endurance and stiffness. According to the increase of spraying amount of NFC, above mentioned paper properties were enhanced without excessive deterioration of drainage. Compared with direct introduction to wet-end, spraying could be regarded as a more proper method to enhance the surface smoothness and strength properties of paper.

• 동아시아식생활학회지
• /
• 제21권6호
• /
• pp.888-896
• /
• 2011

The purpose of this study was to promote the consumption of cereals rich in dietary fiber by substituting brown rice, barley, oat and goami powder for flour in making muffins. All cereals powder was prepared by grinding for 15 min. The appropriate water quantity for cereal powders muffins was set at 105 mL. The volume index of the flour muffins was 132 mL, while that of cereal powders muffins was 117 mL for broun rice muffins, 118 mL for barley muffins, 132 mL for oat muffins and 119 mL for respectively for goami powder muffins. The hardness of the flour muffins, measured by a texture analyzer, was $2.03{\times}10^3\;g/cm^2$, and the other powder muffins were $3.27{\times}10^3\;g/cm^2$ for broun rice muffins, $3.33{\times}10^3\;g/cm^2$ for barley muffins, $2.38{\times}10^3\;g/cm^2$ for oat muffins, and $2.33{\times}10^3\;g/cm^2$ for goami powder muffins respectively. The L-values and moisture contents of goami powder muffins were higher than those of the other muffins. In the sensory evaluation the overall preference was the highest in oat powder muffins.

• Tribology and Lubricants
• /
• 제27권5호
• /
• pp.269-274
• /
• 2011

The purpose of this paper is to study and analyze the improvement method for the failure examples including the vehicle brake system in actual field. It was verified that the indicator plate of pad wear scratched the brake disk because of wearing after displacement of non- identification parts pad. The caliper of other vehicle was installed with brake system verified the phenomenon produced groove in center point because of one side wear when the pad was not fully contacted with the rub disk by other action surface pressure and pad action condition. It verified that the crack phenomenon fatigue was produced by brake thermal deformation because of decreasing the thickness by grinding to modify the non-uniformed wear of brake disk. It verified that the friction sound was produced by the friction phenomenon because of non-uniformed contact of lining and an alien substance with inner of the drum and lining braking by crack phenomenon with brake drum surface.

• 한국세라믹학회지
• /
• 제53권4호
• /
• pp.435-443
• /
• 2016

Coal ash, a material generated from coal-fired power plants, can be classified as fly ash and bottom ash. The amount of domestic fly ash generation is almost 6.84 million tons per year, while the amount of bottom ash generation is 1.51 million tons. The fly ash is commonly used as a concrete admixture and a subsidiary raw material in cement fabrication process. And some amount of bottom ash is used as a material for embankment and block. However, the recyclable amount of the ash is limited since it could cause deterioration of physical properties. In Korea, the ashes are simply mixed and used as a replacement material for cement. In this study, an attempt was made to mechanically activate the ash by grinding process in order to increase recycling rates of the fly ash. Activated fly ash was prepared by controlling the mill types and the milling times and characteristics of the mortar containing the activated fly ash was analyzed. When the ash was ground by using a vibratory mill, physical properties of the mortar mixed with such fly ash were higher than the mortar mixed with fly ash ground by a planetary mill.

• 한국환경과학회지
• /
• 제24권2호
• /
• pp.245-251
• /
• 2015

The main objective of this study is to recovery valuable metals with metal particle size distributions in waste cell phone PCBs(Printed Circuit Boards) by means of pulverization and nitric acid process. The particle size classifier also was evaluated by specific metal contents. The PCBs were pulverized by a fine pulverizer. The particle sizes were classified by 5 different sizes which were PcS1(0.2 mm below), PcS2(0.20~0.51 mm), PcS3(0.51~1.09 mm), PcS4(1.09~2.00 mm) and PcS5(2.00 mm above). Non-magnetic metals in the grinding particles were separated by a hand magnetic. And then, Cu, Co and Ni were separated by 3M nitric acid. Particle diameter of PCBs were 0.388~0.402 mm after the fine pulverizer. The sorting coefficient were 0.403~0.481. The highest metal content in PcS1. And the bigger particle diameter, the lower the valuable metals exist. The recovery rate of the valuable metals increases in smaller particle diameter with same leaching conditions. For further work, it could improve to recovery of the valuable metals effectively by means of individual treatment, multistage leaching and different leaching solvents.

• 한국정밀공학회지
• /
• 제30권5호
• /
• pp.544-551
• /
• 2013

Recently high speed mixer, which is mixing, grinding, dispersion for liquid-liquid material, has been widely used several industries such as food, cosmetics, pharmaceuticals, fine chemicals, electronic material. This high speed mixer has a core element part called particle separation device. Particle separation device, which makes mixed liquid and liquid material using shear forces from a rotor and a stator, is a decisive factor in the distributed parts. In this study, we examined the velocity distribution of the two models of particle separation device using computation fluid dynamics, so that we were able to see the difference of the velocity distribution according to the shape. Also, by experiment, we observed that the use of rotor-screen type is deemed more suitable in case of accurately considering the effect of improving of the dispersibility through the circulation of the future.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.243-249
• /
• 2001

This paper has been presented the hydrodynamic effect by the journal speed, eccentricity and source positions in order to overcome the defects of air bearing such as low stiffness and damping coefficient. Choosing the two row source position of air bearing is different from existed investigations in the side of pressure distribution of air film because of the high speed of journal and the wedge effects by the eccentricity. These optimal chooses of the two row source positions enable us to improve the performance of the film reaction force and loading force as making the high speed spindle. In this paper, the pressure behavior in theory of air film according to the eccentricity of journal and the source positions analyzed. The theoretical analysis have been identified by experiments. The results of investigated characteristics may be applied to precision devices like ultra-precision grinding machine and ultra high speed milling.

• 한국미생물·생명공학회지
• /
• 제8권2호
• /
• pp.125-133
• /
• 1980

토양으로부터 분리한 포도당 이성화효소를 강하게 생산하는 방사균을 Bergey's manual 8판에 따라 동정한 결과 Streptomyces antibioticus 근록의 균주이었다. 본 균의 배양액으로부터 균체를 모아서 해사를 넣고 파쇄 하여 증류수로 추출하고 Mn-처리를 하여 핵단백질을 제거한 후 황산 ammonia 분획침전(0.5∼0.8포화), 수석, DEAE-cellulose column chromatography, DEAE-sephadex (A-50) column chromatography 및 sephadex G-200에 의한 gel filtration을 거쳐 비활성도로 약 380배, 회수율 25％ 정도로 분리 정제하였다.

• 대한기계학회논문집
• /
• 제17권2호
• /
• pp.351-358
• /
• 1993

Recently a high speed spindle system for machine tools has attracted considerable attention to reduce the machining time, to improve the machining accuracy, to perform the machining of light metals and hard materials and to unite the cutting and grinding processes. In this study, a high speed spindle system is developed by applying the oil-air lubrication method, angular contact ball bearings, injection nozzles with dual orifices and so on. And a lubrication experiment for evaluating the performance of the spindle system is carried out. Especially, in order to establish the lubrication conditions related to the development of a high speed spindle system, the effects of oil supply rate, rotational spindle speed and so on are studied and discussed on the bearing temperature rise, bearing temperature distribution and frictional torque. And the effect of spindle system structure on the bearing temperature distribution is investigated.