• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.1
• /
• pp.93-101
• /
• 2006

This research makes a new attempt to apply the activated seawater by electrolysis in the development of two-stage wet scrubber system to control the exhaust gas of large marine diesel engines. First, with using only seawater that is naturally alkaline (pH typically around 8.1). the $SO_2\;and\;SO_3$ are absorbed by relatively high solubility compared to other components of exhaust pollutants, and PM (Particulate Matter) is removed through direct contact with sprayed seawater droplets. Besides, the electrolyzed alkaline seawater by electrolysis, which contains mainly NaOH together with alkali metal ions $(i.e.\;Na^+,\;Mg^{2+},\;Ca^{2+})$, is used as the absorption medium of NOx and $CO_2$. Especially, to increase NOx absorption rate into the alkaline seawater. nitric oxide (NO) is adequately oxidized to nitrogen dioxide $(NO_2)$ in the acidic seawater, which means both volume fractions are adjusted to identical proportion. The results found that the strong acidic seawater was a valid oxidizer from NO to $NO_2$ and the strong alkaline seawater was effective in $CO_2$ absorption In the scrubber test, the SOx reduction of nearly $100\%$ could be achieved and also led to a sufficientPM reduction. Hence, the author believes that applying seawater and its electrolyte would bring the marine air pollution control system to an economical measure. Additionally it is well known that NOx and SOx concentration has a considerable influence on the $N_2O$ emission of green house gas. Although the $N_2O$ concentration exhausted from diesel engines is not as high, the green house gas effect is around 300 times greater than an equivalent volume of $CO_2$. Therefore, we investigated the $N_2O$ removal efficiency with using the electrolyzed seawater too. Finally this research would also plan to treat the effluent by applying electro-dialysis and electro-flotation technique s in the future.

• Journal of Climate Change Research
• /
• v.4 no.1
• /
• pp.27-39
• /
• 2013

In this study, the anthracite coal being used as fuel in Korea were classified into different types. These types include the domestically produced anthracite, imported anthracite used as raw material, and imported anthracite used as fuel. Each of the calorific values and greenhouse gas emission factors were calculated. The calculation of greenhouse gas emission factors resulted in the domestically produced anthracite as $111,477{\pm}4,508kg\;CO_2/TJ$, the imported anthracite used as raw material as $108,358{\pm}4,033kg\;CO_2/TJ$, and anthracite used as fuel was displayed as $103,927{\pm}8,367kg\;CO_2/TJ$. Additionally, the amount of greenhouse gas emission based on these calculated emission factors was displayed as $6,216,942ton\;CO_2$, which resulted as 12.7% lower than the green house gas emission amount which was calculated without distinguishing anthracite coal in details. Therefore, collecting activity data through a detailed classification of anthracites facilitate a more accurate calculation of greenhouse gas emission amount compared to collecting activity data through combination. Furthermore, since the anthracite coal used domestically possesses characteristics differing from the anthracite coal proposed by the IPCC, anthracite coal should be classified for each purpose and calculated for the improvement of the national greenhouse gas inventory.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.491-494
• /
• 2008

The hydrogen fuel and fuel cell which have high energy efficiency and low pollutant emission are getting interest as an alternative energies due to the fossil fuel exhaust, green house effect and atmospheric pollutant problems. The hydrogen gas is very effective as an alternative energy. But, if it is leaked into the air it forms the mixed gas with the air then the danger of the explosion is risen up. So, the secure the safety is mostly important. In this research, to detect the leakage of the hydrogen rapidly, added the odorant materials which don't include the sulfur component into the hydrogen gas and researched on the effect of each odorant on the performance of the fuel cell. As the results, setting the cumulation electric power on the basis and comparing the pure hydrogen, 2,3-Butanedione 5ppm mixed gas 86.1%, 5-Ethylidene-2-Norbornene 17ppm mixed gas 88.2%, Isovaleraldehyde 10ppm mixed gas 74.8%, Ethyl Isobutyrate 2.2ppm mixed gas 93.5% of performance was shown.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.2
• /
• pp.207-218
• /
• 2017

Improving fuel consumption, particularly that of commercial vehicles, has become a global concern. The reduction in logistics cost has been a key issue in efforts to improve fuel economy and efficiency of transportation equipment. Typical technologies for reducing reduce fuel usage include air resistance reduction technologies, tire rolling resistance technologies, and idle technologies among others. Air resistance technology is a highly effective method that can be easily applied in a short period. As with air resistance technology, several devices involving side skirt, boat tail and gap fairing have been developed based on an analytical 3-D modeling technique for reducing air resistance attributed to the vehicle configuration. The devices were on a 45 feet tractor-trailer and the emission test was done using PEMS equipment. Fuel economy was evaluated by introducing several devices to reduce outer air resistance. The test was conducted by changing the experimental method of SAE J1321 Joint TMC/SAE Fuel Consumption Test Procedure - Type II test. As a result, air resistance decreased by at least 15 % and fuel economy improved by at least 13 %. This study sought to reduce greenhouse gas and improve fuel economy by applying several devices to a test vehicle to lower air resistance.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.21 no.1
• /
• pp.39-44
• /
• 2013

The amount of greenhouse gas (GHG) emissions has been increasing steadily over the last 4 years, averaging 6.8 percent a year, due to the growth of low cost carriers and the increased demand for air transportations. For the aviation GHG reduction, various fuel saving activities are implemented in many areas such as high-efficiency aircraft and bio-fuel development in the technical part and low carbon flight procedures, short cut route development in the operational approach. Among the various reduction technologies, we focused on low carbon flight procedures that are crucial to GHG reduciton and suggested a reduction effect according to target implementation rate using by fuel saving estimation data in each aircraft type.

• Resources Recycling
• /
• v.22 no.6
• /
• pp.3-11
• /
• 2013

This study was carried out to estimate greenhouse gas reduction potentials under treatment methods of combustible wastes excavated from closed landfill. The treatment methods of solid wastes were landfilling, incineration, and production of solid recovery fuel. The greenhouse gas reduction potentials were calculated using the default emission factor presented by IPCC G/L method of IPCC (Intergovernmental Panel on Climate Change). The composition of excavated waste represented that screened soil was the highest (65.96%), followed by vinyl/plastic (19.18%). This means its own component is similar to the other excavated waste from unsanitary landfill sites. Additionally, its bulk density was 0.74 $t/m^3$. In case of landfilling of excavated waste, greenhouse gas emission quantity was 60,542 $tCO_2$. In case of incineration of excavated waste, greenhouse gas emission quantity was 9,933 $tCO_2$. However, solid recovery fuel from excavated waste reduced 33,738 $tCO_2$ of the greenhouse gas emission quantity. Therefore, solid recovery fuel production is helpful to reduce of greenhouse gas emission.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.5 no.1
• /
• pp.19-29
• /
• 2002

In this paper, the selection of transport route for import-export container cargo based on the sacrifice model and CO₂ emission was investigated. At first, the transportation of import-export container cargo, the transport share of each transport route, the CO₂ gas emission, the sacrifice model and the time value of import-export container cargo were investigated. And next, the selection of transport route based on the sacrifice model was investigated for the transport of import-export container cargo from Seoul to Pusan Port. Finally, the transport route was also selected by using the sacrifice model including the effect of CO₂ emission. The research results show that the transport route selection results of import-export container cargo based on the sacrifice model represents the present status of the transportation of import-export container cargo very well. And also the research results show that the reduction of transport time was very effective to increase the share of coastal transportation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.8
• /
• pp.1560-1565
• /
• 2011

The environmental pollution caused by green-house gases such as $CO_2$ and $SF_6$ has been becoming the main issue of industrial society. Many developed countries are making efforts to minimize the amount of $CO_2$ emission come from the operation of high voltage electrical apparatuses. As a part of these efforts, 180 countries signed the Kyoto Protocol in 1997 to cut back on their green-house gas emissions. Nowadays, the study on the development of dry air insulated switchgear (DAIS) which is known as an eco-friendly electrical apparatus is in progress. A DAIS is advantageous for minimizing the effect of impurities and enhancing the dielectric characteristics over an air insulated switchgear (AIS) by applying constant pressure to an enclosed cubicle. Therefore, a study on the electrical insulation performance of dry air as a gaseous insulation medium is conducted in this paper to substitute a gas insulated switchgear (GIS) for DAIS. As results, it is verified that the AC dielectric characteristics of dry air are similar to those of air and the lightning impulse dielectric characteristics of dry air are superior to those of air at 1bar pressure condition. However, dry air is of inferior dielectric characteristics to $SF_6$ at 4bar pressure condition. Finally, it is suggested that the internal pressure of DAIS should be over 4bar pressure to develop a high voltage switchgear which has similar electrical performance to a conventional GIS. Also, the empirical formulae on calculating the maximum electric field intensity at sparkover of dry air are deduced by experiments according to pressures. It is expected that these results are helpful to design and develop a high voltage electrical apparatus.

• Journal of ILASS-Korea
• /
• v.19 no.3
• /
• pp.115-122
• /
• 2014

As a demand for an automobile increases, air pollution and a problem of the energy resources come to the fore in the world. Consequently, governments of every country established ordinances for green-house gas reduction and improvement of air pollution problem. Especially, as international oil price increases, engine using clean energy are being developed competitively with alternative transportation energy sources development policy as the center. Bio ethanol, one of the renewable energy produced from biomass, gained spotlight for transportation energy sources. Studies are in progress to improve fuel supply methods and combustion methods which are key features, one of the engine technologies. DI(Direct Injection), which can reduce fuel consumption rate by injecting fuel directly into the cylinder, is being studied for Green-house gas reduction and fuel economy enhancement at SI(Spark Ignition). GDI(Galoine Direct Injection) has an advantage to meet the regulations for fuel efficiency and $CO_2$ emissions. However it produces increased number of ultrafine particles, that yet received attention in the existing port-injection system, and NOX. As fuel is injected into the cylinder with high-pressure, a proper injection strategy is required by characteristics of a fuel. Especially, when alcohol type fuel is considered. In this study, we tried to get a base data bio-ethanol mixture in GDI, and combustion for optimization. We set fuel mixture rate and fuel injection pressure as parameters and took a picture with a high speed camera after gasoline-ethanol mixture fuel was injected into a constant volume combustion chamber. We figured out spraying characteristic according to parameters. Also, we determine combustion characteristics by measuring emissions and analyzing combustion.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.22 no.4
• /
• pp.25-33
• /
• 2014

As global warming becoming an environmentally serious issue, more attention is drawn to fuel consumption which is the direct source of green house gas emission. The fuel consumption by aircraft operation is not an exception. Motivated by the societal and environmental context, this paper explains a method for estimation of aircraft fuel consumed during their flights as well as the computational process using real flight track data. Applying so-called 'Total Energy Model' along with aircraft specific parameters provided in EUROCONTROL's Base of Aircraft Data (BADA) to aircraft radar track data, we estimate fuel consumption of individual aircraft flown between Gimpo and Jeju airports. We then assess the estimation accuracy by comparing the estimated fuel consumption with the actual one collected from an airline. The computational results are quite encouraging in that the method is able to estimate the actual fuel consumption within ${\pm}6{\sim}11%$ of error margin. The limitations and possible enhancements of the method are also discussed.