• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2019년도 학술발표회
• /
• pp.418-418
• /
• 2019

낮은 수심, 저 유속의 수로 자갈층에 형성된 생물막을 이용하여 오염물질을 제거하는 박층류 자연정화기법의 효율적인 설계와 운영지침을 얻기 위하여 경기도 용인시 오산천 일부 구간에 현장적용을 위한 Test-bed를 조성하여 박층류 자연정화수로에서의 오염물질 제거 효율을 조사하였다. 오염물질은 녹조발생의 주요 원인물질인 인과 질소를 대상으로 하였고, 연구 조건은 일반적인 하천수에서의 오염 조건과 비점오염원으로부터 오염물질이 유입된 오염조건의 두 가지 조건을 가정하여 제거효율을 분석하였다. 분석 결과 모든 조건에서 박층류 수로를 통과할 때 오염물질의 농도가 감소함을 확인할 수 있었다. 특히 T-P 3 mg/L 이상, T-N 20 mg/L 이상의 고농도의 오염물질 유입시에 박층류 자연정화수로는 평상시보다 높은 60% 이상의 높은 제거 효율을 보였는데, 이를 통하여 박층류 자연정화기법이 고농도의 오염물질 제거에서도 제한적이지 않고 오히려 더 효과적임을 알 수 있었다.

• 한국광학회지
• /
• 제1권1호
• /
• pp.28-32
• /
• 1990

방전가열형 구리증기레이저를 제작하였으며 그 동작특성을 조사하였다. 레이저관으로는 내경 25mm, 길이 106cm 인 고순도(99.8%) 알루미나관을 이용하였다. 방전전극은 molybdenum 튜브로 제작하였으며 전극간의 거리는 108cm 이었다. Ne 가스압력 40mbar, 충전전압 10kV, 반복률 5KHz, 레이저관 내부온도 $1500^{\circ}C$일 때 평균출력 10W를 얻었다.

• 지구물리와물리탐사
• /
• 제2권2호
• /
• pp.86-95
• /
• 1999

이 연구에서는 적분방정식의 근사해를 이용한 3차원 모델링 알고리듬을 구성하고 그 효율성을 분석하였다. 전기장 적분방정식에 확장 Born 근사(extended Born approximation)를 적용시켜 알고리듬을 구성하였으며 모델링의 계산 속도를 향상시키기 위하여 Green 텐서 적분을 공간 주파수 영역에서 수행하였다. 이 방법은 연속 함수로 표현되는 전기전도도를 갖는 이상체에 대한 모델 계산을 가능하게 하고, Green 텐서 적분시 발생하는 특이치 문제가 발생하지 않는 장점이 있다 얇은 전도체에 대한 모델링 계산 결과를 적분방정식의 해와 비교하여 알고리듬의 타당성을 검증하였다. 전기전도도 물성차, 사용 송신원의 주파수에 따른 개발된 알고리듬의 분석을 통하여 물성차 1:16 정도, 사용주파수는 100 Hz-100 kHz까지 정확한 결과를 얻었다. 그러나, 확장 Born 근사는 송신원과 모델의 상대적인 위치에 따라 오차를 나타내었다. 한편, 연속적인 전기전도도 함수를 갖는 모델에 대한 이 알고리듬의 적용성를 알아보기 위하여 서로 다른 전기전도도를 갖는 두 이상체가 접합한 모델에 대하여 적분방정식의 해와 비교하였으며 양호한 결과를 나타내었다.

• 멤브레인
• /
• 제22권3호
• /
• pp.201-207
• /
• 2012

본 연구에서는 PDMS (poly-dimethylsiloxane)와 PEBAX (polyether block amides) 분리막을 이용해 $N_2$, $O_2$, $CF_4$와 $SF_6$의 단일 기체 투과특성에 관하여 연구하였다. 다양한 압력으로 공급된 기체의 투과유량을 진공가압 연속흐름방식으로 측정하였으며, 이를 이용하여 투과도를 산정하였다. PDMS 분리막에서는 상부의 압력이 증가할수록 $SF_6$를 제외한 다른 기체의 투과도는 감소하였다. 또한 $SF_6$의 투과도가 $CF_4$보다 높게 나타나고 있으며 이것은 $SF_6$가 더 높은 임계온도를 가지고 있기 때문이다. PDMS 분리막에서 투과도는 $O_2$ > $N_2$ > $SF_6$ > $CF_4$ 순으로 감소하였다. 반면에 PEBAX 분리막에서 기체의 투과 경향은 $O_2$ > $N_2$ > $CF_4$ > $SF_6$ 순으로 감소하였다. 이러한 경향은 각 기체의 운동 반경의 크기(${\AA}$)($SF_6$ > $CF_4$ > $N_2$ > $O_2$) 순서와 반대로 나타났다. $SF_6/CF_4$의 순수 기체의 선택도는 PDMS 분리막에서 0.7 MPa일 때 2.1로 나타났다.

• 천문학회보
• /
• 제38권2호
• /
• pp.89.1-89.1
• /
• 2013

We present a multiwavelength study of the X-class flare, which occurred in active region (AR) NOAA 11339 on 3 November 2011. The EUV images recorded by SDO/AIA show the activation of a remote filament (located north of the AR) with footpoint brightenings about 50 min prior to the flare occurrence. The kinked filament rises-up slowly and after reaching a projected height of ~49 Mm, it bends and falls freely near the AR, where the X-class flare was triggered. Dynamic radio spectrum from the Green Bank Solar Radio Burst Spectrometer (GBSRBS) shows simultaneous detection of both positive and negative drifting pulsating structures (DPSs) in the decimetric radio frequencies (500-1200 MHz) during the impulsive phase of the flare. The global negative DPSs in solar flares are generally interpreted as a signature of electron acceleration related to the upward moving plasmoids in the solar corona. The EUV images from AIA $94{\AA}$ reveal the ejection of multiple plasmoids, which move simultaneously upward and downward in the corona during the magnetic reconnection. The estimated speeds of the upward and downward moving plasmoids are ~152-362 and ~83-254 km/s, respectively. These observations strongly support the recent numerical simulations of the formation and interaction of multiple plasmoids due to tearing of the current-sheet structure. On the basis of our analysis, we suggest that the simultaneous detection of both the negative and positive DPSs is most likely generated by the interaction/coalescence of the multiple plasmoids moving upward and downward along the current-sheet structure during the magnetic reconnection process. Moreover, the differential emission measure (DEM) analysis of the active region reveals presence of a hot flux-rope structure (visible in AIA 131 and $94{\AA}$) prior to the flare initiation and ejection of the multi-temperature plasmoids during the flare impulsive phase.

• KIEAE Journal
• /
• 제13권2호
• /
• pp.113-122
• /
• 2013

On July 2004, the brand new CASBEE for construction (Brief version) has completed while trying to highlight and improve major items adequate for each region's characteristics in Japan; at the same time, from the start of NAGOYA CITY (operated since April 2004) to the point of May 2011, it has been mandatory for specified size buildings in 23 regions by law. Evaluation sheet of CASBEE is published on each region's home page and various genre of information on building evaluation which is scheduled to be completed by 2016 and is for 5-6 years of quantity is accumulated until October 2012. It is good study resource to verify how new buildings being evaluated are closely match with CASBEE's original purport (eco-friendly, energy efficiency, publicity etc). Particularly, for Japan's multi-family housing where small sized mid to high level single housing type is majority in city, it is an important point that improved performance on eco-friendly buildings have more value in city rather than suburb. Categorized score through evaluation is a resource to confirm the latest trend of multi-family housing built in congested city; on the other hand, demand of the time can be recognized by the score focused on category. It is meaningful resource to determine the adequacy of evaluated items and the degree of reality.

• 펄프종이기술
• /
• 제47권5호
• /
• pp.98-103
• /
• 2015

The reduction of the energy consumption in papermaking process become more important issue because of the regulation of green house gas (GHG) emission. Since more than half of energy for papermaking process is consumed during drying process, the increase of the drying efficiency would be very important solution for saving energy and reduction of GHG emission. The improvement of drying efficiency could be very difficult for the liner board mill because the liner board are usually made of recycled paper, OCC (old corrugated container). The short fiber and fines originated the OCC lead to compact sheet structure and delay the water flow out during wet pressing process and drying process. The application of lignocellulose spacer could provide more loose wet sheet structure and result in the higher drainage rate and the improved drying efficiency. In this study, the effects of the application of lignocellulose spacer to the liner board mill were evaluated based on the mill trial. In order to overcome the common disadvantage of the spacer, the loss of strength properties, the spacer was pretreated with amphoteric polyelectrolyte during mill trial. The results showed the application of pretreated spacer improved the drying efficiency by reducing steam consumption. And the loss in the strength properties by the spacer could be supplemented by the pretreatment.

• 접착 및 계면
• /
• 제16권1호
• /
• pp.15-21
• /
• 2015

본 연구에서는 자동차 선도장 강판용 베이스코트 도료들의 유변물성 및 롤코팅 공정에서의 유동 특성을 고찰하였다. 베이스코트 3종 색상 도료들의 상온 조건에서 전단 점도와 열경화 조건에서 탄성/점성 모듈러스의 변화를 회전형 유변물성 측정기를 통해 분석하였다. 이를 통해 작용기의 배합비율과 열경화 이전의 전단 점도 특성이 경화에 의한 도료 내 가교구조 형성에 큰 영향을 주었음을 확인하였다. 또한, 3-롤코팅 공정에서 베이스코트 도료들의 코팅 특성 및 유동 불안성정을 관찰하여 코팅 운전 영역을 설정하였다. 이러한 유변학적 접근법은 비뉴튼성 도료의 친환경적 선도장강판 코팅 기술 개발 및 최적의 안정한 조건 설정을 위해 유용하게 활용될 수 있음을 보였다.

• 대한가정학회지
• /
• 제17권3호
• /
• pp.53-59
• /
• 1979

Vitamin contents of three grades of Korean laver high, medium and low were measured. They were cooked by different methods to examine changes in their vitamin content. Results of this experiment are as follows ; 1. Vitamin contained in loogr of laver amount to 13,200 I.U, for high grade, 16,100 for mediium grade, and 16,400 for low grade . The low -grade laver, which is interwoven with green laver, showed the highest vitamin content. 2. When laver was broiled sheet by sheet, its vitamin loss rate was 11% for high grade, 19% for medium grade, and 20% for low grade. Thus , the one with a higher vitamin content showed a higher vitamin loss rate. When two sheets of laver, which were put upon each other, were broiled, their vitamin loss rates were 2.3% for high grade, 1.73 % for medium grade, and 2.64% for low grade. Thus broiling laver at the unitof two to three sheets together is a way of decreasing the vitamin loss rate. 3. When laver was broiled with salt applied on its surface , its vitamin loss rate was 8.3% for high grade, 13% for medium grade, and 10.9% for low grade. When laver was broied at the unit of two sheets together after salt and sesame oil were added, its vitamin loss rate was 2.2% for high grade, 5.2% for medium grade, and 8.2% for low grade . The one with a higher vitamin content showed a higher vitamin loss rate. 4. When laver was mixed seasoned soysauce, its vitamin loss rate increased in process of time. In 48 hours after laver was mixed with seasoned soysauce , its vitamin loss rate read 24.2%, 27.1% and 35% respectively, for the three grades of laver. Thus the laver mixed with seasoned soysauce has to be used right after so cooked so as to obtained the highest possible vitamin content.

• 패션비즈니스
• /
• 제16권5호
• /
• pp.207-219
• /
• 2012

It is intended to study the colors of work environment and the working clothes colors between humans and environment with application of the arrangement of working clothes colors to domestic machinery companies that play pivotal roles in the industry of Korea. The purpose of this study is to provide the foundation of color plan for the integrated environmental harmonization and the safety of industrial sites by analyzing the photographs of working clothes in the sires in consideration of the functions of colors (clearness, attention-getting, and safety) using the Faber Birren's Color Harmony and by analyzing the result of a questionnaire survey. The study was conducted by the method to shoot a worksite using a digital camera after wearing 24 sets of uniforms, which were developed by the color plan established in a previous study, in the same worksite. The shooting place was an outdoor steel sheet inspection site of D company, a machinery company in Changwon-si, Gyeongnam, and the intensity of illumination was 2400lux. 24 pieces of images were printed in 5x7 inch size and a questionnaire survey was performed at 5-point scale. The questionnaire survey was performed for 13 subjects consisting of 6 field professionals having more than 30 years of experiences, 4 clothes color professionals, and 3 industrial engineering professionals. The result of the survey was statistically analyzed by the method of frequency analysis using IBM SPSS Statistics 20 Program. As the result of assessment of basic four colors (yellow green, sky blue, blue, and violet) of working clothes, yellow green, sky blue, and blue showed high mean values in (Tint)+(Shade)+(Tone)+(Gray) equation indicating that its is a harmonized equation.