• 한국산업융합학회 논문집
• /
• 제10권1호
• /
• pp.33-38
• /
• 2007

Door guide rail is the core part which guides window when it moves up and down. But when the method of grease lubrication in the core has been used for a long times, its lubrication performance has been weakened. Therefore the method of the solid lubrication such as teflon(PTFE) coating in the rail has been studied to be increased the performance in these days. In this study the friction wear characteristic the surface with teflon coating of door guide rail for automobile has been researched. In 1, 20 Hz frequency friction wear tests the friction coefficient are below 0.188 and 0.213. In indicate test the wear depth is very slight. Therefore the durability to the friction wear in the surface with teflon coating of door guide rail is good. In addition to, the result of this study can make efficient use to a basic study to develop method of test evaluation to door guide rail surface grade. Especially this study will contribute to improve the quality of automobile parts.

• Tribology and Lubricants
• /
• 제18권4호
• /
• pp.255-259
• /
• 2002

The tribological properties of eight different liquid crystals were investigated in a concentrated point contact device and a ball-on-flat contact. For comparison, the same tests were also performed with commercial greases and the corresponding base oils. Under the fully flooded conditions studied, liquid crystals in a concentrated point contact showed lower friction than commercial greases and greater film thickness dependence on rolling speed than grease base oils or greases. Test results also showed that the film thickness and friction were little influenced by the composition of the examined liquid crystals.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.247-256
• /
• 1999

This paper describes the results of analysis, syntheses and Roll Stability of various Di-urea greases. Di-urea greases were synthesized by reaction of 4,4'-Methylenebis(phenyl isocyanate) and various amines, such as cyclohexylamine, octylamine, stearylamine and p-toluidine with base oil at 80-180 $^{\circ}C$. The synthesized di-urea greases were analyzed by FT-R spectroscopy. The Roll Stability of synthesized di-urea greases was evaluated.

• Tribology and Lubricants
• /
• 제19권4호
• /
• pp.223-229
• /
• 2003

The sliding wear characteristics of the crane sheave were investigated using a pin-on-disk rig tester. The experiment was conducted using a high carbon steel wire that was upper material, also carbon steel castings that was disk material. There are various operating conditions in this work. At the room temperature, we carried out the wear test under a grease lubrication and dry condition. The results of wear test showed that an annealed-casted have lower, also the wear curves are linearly increased with increasing of sliding distance. For the specific wear rate of annealed-casted, the wear resistance was increased with decreasing diameter of wire. The wear of a wire and a disk have a different mechanism, the one is the abrasive wear due to fatigue wear under lubrication, another is the adhesion wear under dry condition.

• 한국철도학회논문집
• /
• 제9권6호
• /
• pp.630-634
• /
• 2006

Rail car axles are very important parts for safety of passengers and structural integrity of vehicles. The axles are supported by bearings. To seal grease lubricating the bearings of freight cars, an oil seal has been developed. The developed oil seal is composed of an inner plate, an outer plate and a seal rubber. The friction between axle and housing with the developed oil seal is very low. The seals are designed for a minimum life expectancy of 800,000 kilometers service. In this study, an accelerated durability tests according to AAR Specification M-934-82 were carried out. In addition, various performance tests according to KS B 2804 were conducted.

• 대한기계학회논문집A
• /
• 제27권11호
• /
• pp.1873-1880
• /
• 2003

The sliding wear characteristics of the crane sheave were investigated using a pin on disk rig tester. The experiment was conducted using a high carbon steel wire that was upper material, also carbon steel castings that was disk material. There are various operating conditions in this work. At the room temperature, we carried out the wear test under a grease lubrication and dry condition. The results of wear test showed that an annealed-casted have lower, also the wear curves are linearly increased with increasing of sliding distance. For the specific wear rate of annealed-casted, the wear resistance was increased with decreasing diameter of wire. The wear of a wire and a disk have a different mechanism, the one is the abrasive wear due to fatigue wear under lubrication, another is the adhesion wear under dry condition.

• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.761-766
• /
• 2013

A precision linear motion table plays a crucial role in manufacturing systems used in various industries such as machine tools, semiconductors, and nanofabrication. In particular, one of the most typical mechanisms for a linear motion table is to use a ballscrew and LM guides. However, this mechanism is inevitably influenced by friction because of the relative motion in its joint regions. One of the most complex phenomena in friction is the hysteresis behavior of dynamic friction, which was compared with the steady dynamic friction that was presented using a Stribeck curve in this study. Therefore, we investigated the dynamic friction and its hysteresis behavior using a miniaturized linear table equipped with a ballscrew and LM guides that were lubricated with grease. Subsequently, it could be seen that hysteresis could be considered a time delay after zero-velocity crossing and that it was influenced by acceleration.

• Tribology and Lubricants
• /
• 제35권2호
• /
• pp.87-93
• /
• 2019

This work aims to develop a dry lubricant for oilless bush, especially a solid lubricant, thereby creating a coating method with improved properties of anti-friction and load-carrying capacity without oil lubrication. In this work, spherical-shaped powders of thermosetting resin such as polyimide (PI) are mixed with a binder matrix obtained by mixing a fluorocarbon compound resin such as Polytetrafluoroethylene (PTFE) or Ethylene tetra fluoro ethylene (ETFE) with itself or with a non-fluorocarbon thermoplastic resin such as Polyether ether ketone (PEEK). And these dry lubricant mixtures are thickly coated (200-300 mm in the thickness) on the inner surface of the bush by using a wet-typed air-spray deposition method. It was found that the load-carrying capacity of the solid lubricant for excavator bush (60 mm in diameter) that operates under a high load condition (at 40 MPa) is greatly improved owing to the spherical-shaped powders of thermosetting resin. In addition, the coefficient of friction at the sliding surface is also reduced less than 0.1. Thick coating also lowers the contact stress at the edge of a bush that results in better tribological performances. The result suggests that the lubrication performance and durability life of the bush can be remarkably improved even without lubrication (oil or grease).

• Tribology and Lubricants
• /
• 제22권6호
• /
• pp.335-341
• /
• 2006

This paper reports the wear characteristics of two types of coating materials, which are $Cr_2O_3$ and $ZrO_2$, by coated plasma thermal spray method. The wear test was carried out under air, grease, and bearing fluid conditions. The wear testing machine of a pin-on disk type were used to measure friction forces, friction coefficients and the weight losses of the coating specimens on the various sliding velocity and loading condition. The wear surface of specimens were observed by scanning electron microscope (SEM) photographs.

• 소성∙가공
• /
• 제3권2호
• /
• pp.215-228
• /
• 1994

The purpose of this paper is to pursue a general method to determine both the flow stress of a material and the friction factor by ring compression test. The materials are assumed to obey the expanded n-power hardening rule including the strain-rate effect. Ring compression is simulated by the rigid-plastic finite element method to obtain the database used in determining the flow stress and friction factor. The Simulation is conducted for various strain hardening exponent, strain-rate sensitivity, friction factor, and compressing speed, as variables. It is assumed that the friction factor is constant during the compression process. To evaluate the compatibility of the database, experiments are carried out at room and evaluated temperature using specimens of aluminum 6061-T6 under dry and grease lubrication condition. It is shown that the proposed test method is useful and easy to use in determining the flow stress and the friction factor.