• Journal of the Korea Concrete Institute
• /
• v.22 no.5
• /
• pp.727-736
• /
• 2010

This paper describes results of an preliminary study to produce strain hardening cement-based composites (SHCCs)with consideration of sustainability for infrastructure applications. The aims of this study are to evaluate the influence of recycled materials on the mechanical characteristics of SHCCs, such as compressive, four-point bending, and direct tensile behaviors, and to give basic data for constitutive model for analyzing and designing infra structures with SHCCs. In this study, silica sand, cement, and PVA fibers, were partially replaced with recycled sand, fly-ash, and FET fibers in the mixture of SHCCs, respectively. Test results indicated that fly-ash could improve both bending and direct tensile performance of SHCCs due to increasing chemical bond strength at the interface between PVA fibers and cement matrices. However, SHCCs replaced with PET fibers showed much lower performance in bending and direct tensile tests due to originally low mechanical properties of own fibers, although compressive behavior is similar to PVA2.0 specimen. Also, it was noted that the recycled sand would increase elastic modulus of SHCCs due to larger grain size compared to silica sand. Based on pre-set target value to maintain the performance of SHCCs, it was concluded that the replacement ratio below 20% of fly-ash or below 50% of recycled sands would be desirable for creating sustainable SHCCs.

• Economic and Environmental Geology
• /
• v.37 no.5
• /
• pp.499-508
• /
• 2004

Changwon City first constructed riverbank filtration plants in Book-Myeon and Daesan-Myeon in Korea in the year 2001. This study evaluated hydrogeological characteristics and groundwater flow simulation between the Nakdong River and the fluvial aquifers adjacent to the river in Book-Myeon, Changwon City. The groundwater simulation calculated the influx rate from the Nakdong River and the fluvial aquifers to pumping wells through the riverbank filtration system. The groundwater flow model utilized drilling, grain size analysis, pumping test, groundwater level measurements, river water discharge and rainfall data. Hydraulic heads calculated by the steady-state model closely matched measured heads in pumping and observation wells. According to the transient flow model, using a total pumping amount of 14,000 $m^3$/day, the flux into the pumping wells from the Nakdong River accounts for 8,390 $m^3$/day (60%), 590 $m^3$/day (4%) is from the aquifer in the rectilinea. direction to the Nakdong River, and 5,020 $m^3$/day (36%) is from the aquifer in the parallel direction to the Nakdong River. The particle tracking analysis shows that a particle from the Nakdong River moves toward the pumping wells at a rate of about 1.85 m/day and a particle from the aquifer moves toward the pumping wells at a rate of about 0.75 m/day. This study contributes to surface water/groundwater management modeling, and helps in understanding, how seasonal change affects pumping rates, water quality, and natural recharge.

• Journal of Astronomy and Space Sciences
• /
• v.21 no.2
• /
• pp.141-152
• /
• 2004

Optics fabrication process for precision space optical parts includes bound abrasive grinding, loose abrasive lapping and polishing. The traditional bound abrasive grinding with bronze bond cupped diamond wheel leaves the machine marks of about $20{mu}m$ rms in height and the subsurface damage of about 1 ${mu}m$ rms in height to be removed by subsequent loose abrasive lapping. We explored an efficient quantitative control of precision CNC grinding. The machining parameters such as grain size, work-piece rotation speed and feed rate were altered while grinding the work-piece surfaces of 20-100 mm in diameter. The input grinding variables and the resulting surface quality data were used to build grinding prediction models using empirical and multi-variable regression analysis. The effectiveness of such grinding prediction models was then examined by running a series of precision CNC grinding operation with a set of controlled input variables and predicted output surface quality indicators. The experiment achieved the predictability down to ${pm}20$ nm in height and the surface roughness down to 36 nm in height. This study contributed to improvement of the process efficiency reaching directly the polishing and figuring process without the need for the loose abrasive lapping stage.

• The Journal of Engineering Geology
• /
• v.10 no.2
• /
• pp.18-35
• /
• 2000

The most dominant type of landslide in Korea is debris flows which mostly take place along mountain slopes during the rainy season, July to August. The landslides have been reported to begin activation when rainfall is more than 200mm within 2days. The debris flows are usually followed by translational slips which occur upper part of mountain slopes and they transit to debris flow as getting down to the valleys. Lithology, location, slope inclination, grain size distribution of soil, permeability, dry density and porosity have been proved as triggering factor causing translational slides. The triggering data taken from mapping are statistically analysed to get landslide potential quantitatively. Rock mass creeps mostly occur on well bedded sedimentary rocks in Kyeongsang Basin. Although the displacement of rock mass creep is relatively small about 1m, the creep can cause severe hazards due to relatively large volume of the involved rock mass. Examples are rock mass creep occurred in the mouth of Hwangryongsan Tunnel, in Chilgok and in Sachon in 1999. Although the direct factor of the creeps are due to slope cutting at the foot area, more attention is required A rotational slide occurring within thick soil formation or weathered rock is also closely related to bottom part of slope cutting. It is propagated circular or semi-circular type. Especially in korea, the rotational slide may be frequently occurred in Tertiary tuff area. Because they are mainly composed of volcanic ash and pyroclastic materials, well developed joints and high degree of swelling and absorption can easily cause the slide. The landslide among the Pohang-Guryongpo national road is belong to this type of slide.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.4 no.2
• /
• pp.107-116
• /
• 1999

To study the characters of surface sediment and to describe the seasonal depositional environment as a result of sedimentation process off Byun-San Peninsula, a total 61 samples of surface sediment (32 samples in summer; 29 samples in winter) were collected and analysed. A digitized depth data from sea chart and echosounding profiles along five trans-sections were helpful for understanding the morphological factors. The types classified by the characters of surface sediment are type I (sand, S), type II (silty sand, zS), and type ill (sandy silt, sZ). Mean grain size varies from 2.11 to 7.81 ${\Phi}$. The positive-skewness shows the typical tide-dominated environment. The sediment type of the northwestern stations is medium sand and the sorting value is 0.5~1.4 ${\Phi}$ of well/moderately sorted. Meanwhile, other stations are composed of muddy sands and sandy muds transported from rivers and offshore. These sediment types toward inshore change gradually from silty sand to sandy silt. According to the C/M diagram, there are three major transport modes of sediment: bed load (Mode A), graded suspension (Mode B), and suspension (Mode C), correlating with north-eastern sandy area, middle part of silty-sand area, and southern sandy-silt area, respectively. The result of Principal Component Analysis shows also similar pattern of sediment types. In result, sediment texture of type III tends to be finer and more poorly-sorted than that of type II and sediment facies are correlateed with sedimentation process.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1716-1720
• /
• 2007

연안 해역에서의 표사는 하천에서의 유사가 주요한 공급원이므로 산지-하천-해안을 통합한 유사 및 표사에 관한 관리가 필요하며, 해안수리 및 환경적인 측면에서 강성 연안구조물의 건설을 통하지 않고 연안에서의 침식을 억제해야하는 방지대책의 수립 요구가 증대하고 있는 실정이다. 즉 연안에서의 침식, 퇴적관계는 토사공급원의 장기적인 확보여부가 중요하며 하천에서 해안역으로 공급되는 유사량을 예측하고 또한 이들이 어떻게 효과적으로 연안 해역으로 이송되어 가는가를 파악하는 것은 연안표사문제를 이해하는데 매우 중요한 요소이다. 이를 위해서는 무엇보다도 하천에서 연안 해역으로의 유사량을 파악하는 것이 중요하며 그리고 하천 유사량이 하구에 사주를 형성하고 어떤 형태를 거쳐 연안표사로 이동하는가 하는 특성을 파악할 필요가 있다. 울산광역시 울주군 온산읍에 위치한 회야강의 하구폐색은 1990년대 중반부터 연구의 관심이 되어오고 있으며, 1986년 회야강 상류 회야댐 건설 이후 하구폐색이 가속화됨에 따라 매년 회야강 하구에서의 준설이 필요한 실정이다. 특히 회야강 하구부에서는 파랑류, 취송류와 하천류 뿐만 아니라 해류나 조류 등에 의한 흐름과 지형특성등 복합적으로 발생하는 하구현상에 의해 하구에서의 사주 발달이 상대적으로 강하여 하구폐색이 강하게 나타나고 있다. 이의 대책으로 최근 회야강 하구부에 도류제가 건설되었으며 이에 따른 장기적인 하구부 하상변동특성과 토사이동의 특성 파악이 요구되고 있는 실정이다. 본 연구에서는 이 같은 관점에서 회야강 하구부의 도류제 설치에 따른 하구에서의 지형변동과 유송토사량의 특성을 파악하기 위해 하천 상류부에서는 동적 평형상태의 유사량을 가정하고 하상재료 및 유사는 혼합입경으로 하여 하상고 및 하상교환층 중의 입도조성의 시간변화를 구하여 1차원적인 하상변동과 토사이동 특성을 해석하였다.했을 때, 대표입경을 통해 얻은 조도계수가 보정 조도계수보다 다소 작은 것으로 해석되었다.하고자 한다.해결책을 얻어내는 상호보완적인 결과를 추구한다. 그가 디자인하는 작품은 전형적인 이미지를 내포하지 않는다. 즉 그의 작품은 기존의 가치와 이념적인 것은 배제하고, 창의적인 개념을 도출하였다.형모서리는 건물 특화 성격이 강하므로 불가피할 경우 소형 액센트 광고 위치를 미리 벽면으로 할애하는 것이 경관 및 입면계획에 유리한 것으로 분석되었다. 불확실도 해석모형 등의 새로운 기능을 추가하여 제시하였다. 모든 입출력자료는 프로젝트 단위별로 운영되어 data의 관리가 손쉽도록 하였으며 결과를 DB에 저장하여 다른 모형에서도 적용할 수 있도록 하였다. 그리고 HyGIS-HMS 및 HyGIS-RAS 모형에서 강우-유출-하도 수리해석-범람해석 등이 일괄되게 하나의 시스템 내에서 구현될 수 있도록 하였다. 따라서 HyGIS와 통합된 수리, 수문모형은 국내 하천 및 유역에 적합한 시스템으로서 향후 HydroInformatics 구현을 염두에 둔 특화된 국내 수자원 분야 소프트웨어의 개발에 기본 토대를 제공할 것으로 판단된다.았다. 또한 저자들의 임상병리학적 연구결과가 다른 문헌에서 보고된 소아 신증후군의 연구결과와 큰 차이를 보이지 않음을 알 수 있었다. 자극에 차이가 있지 않나 추측되며 이에 관한 추후 연구가 요망된다. 총대장통과시간의 단축은 결장 분절 모두에서 줄어들어 나타났으나 좌측결장 통과시간의 감소 및 이로 인한 이 부위의 통과시간 비율의 저하가 가장 주요하였다. 이러한 결과는 차가운 생수 섭취가 주로 결장 근위부를 자극하는 효과를 발휘하는 것이 아닌가 해석된다. 이와 같은 연구결과를 통해 생다시마를 주원료로 개발된 생다시마차와 생다시마 음료가 만성 기능성 변비 증세를 개선하는 효능이 잠재적으로 있음을 확인하였다.

• Economic and Environmental Geology
• /
• v.30 no.4
• /
• pp.279-289
• /
• 1997

Dark to pale green-colored, Cr-bearing sericites from hydrothermal alteration zone of the Narim gold deposit were investigated mineralogically and geochemically. The alteration zone is composed mineralogically of quartz, carbonate minerals and green sericite with minor amounts of chlorite, barite and sulfide minerals (pyrite, sphalerite, galena). The zone is enriched in As (967 to 1520 ppm), Cu (31 to 289 ppm), Ni (1027 to 1205 ppm), Pb (0.20 to 1.24 wt.%) and Zn (1.03 to 1.07 wt. %) compared with fresh rocks such as granitic gneiss, porphyritic biotite granite and basic dyke. The Cr, probably the chromophore element, is highly enriched in the alteration zone (1140 to 1500 ppm), host granitic gneiss (1200 ppm) and porphyritic biotite granite (1200 ppm). Occurrence and grain size of sericite are diverse, but most of the Cr-bearing sericites (150 to $200{\mu}m$ long and 20 to $30{\mu}m$ wide) occur along the boundaries between ore veins and host rocks (especially basic dyke and granitic gneiss). X-ray diffraction data of the sericite show its monoclinic form with unit-cell parameters of $a=5.202{\AA}$, $b=8.994{\AA}$, $c=20.103{\AA}$, ${\beta}=95.746^{\circ}$ and $V=935.83{\AA}^3$, which are similar with the normal 2M1-type muscovite. Representative chemical formula of the sericite is ($K_{1.54}Ca_{0.03}Na_{0.01}$)($Al_{3.42}Mg_{0.38}Cr_{0.14}Fe_{0.06}V_{0.02}$)($Si_{6.69}Al_{1.31}$)$O_{20}(OH)_4$. The Cr content increases with decrease of the octahedral Al content, and ranges from 0.36 to 2.58 wt.%. DTA and TG curves of the sericite show endothermic peaks at $342^{\circ}$ to $510^{\circ}$, $716^{\circ}$ to $853^{\circ}$ and $1021^{\circ}C$, which are due to the expulsion of hydroxyl group. The total weight loss by heating is measured to be about 8.8 wt. %, especially at $730^{\circ}C$. Infrared absorption experiments of the sericite show broad absorption band due to the O-H bond stretching vibration near the $3625cm^{-1}$, coupled with the 825 and $750cm^{-1}$ doublet. The vibration bands related with the H-O-Al and Si-O-Al bonds occur at $1030cm^{-1}$ and 500 to $700cm^{-1}$, respectively. Based on paragonite content of the sericite, the formation temperature of the Narim gold deposit is calculated to be $220{\pm}10^{\circ}C$.

• Korean Journal of Environmental Biology
• /
• v.36 no.2
• /
• pp.107-116
• /
• 2018

In this study, the distribution of sedimentary environment and benthic macro-fauna in habitats and non-habitats of Zostera marina were investigated. The purpose of this study was to obtain basic data about the sedimentary environment and benthic macro-fauna in the habitats and non-habitats of Z. marina. Sand was dominant within habitat environments, whereas the non-habitats were predominantly composed of silt. As a result, the habitats of Z. marina have a different grain size and organic matter content compared to the non-habitats. These differences in the sedimentary environment were expected to influence the species composition of benthic animals. Benthic communities in the habitats of Z. marina showed a higher density and a greater number of species than in the non-habitats. As a result of an ecological index evaluation, the species diversity index (H') was $3.44{\pm}0.10$ for the habitat; the non-habitat was analyzed as $2.34{\pm}0.35$. It was also found that the stability of community in the habitats was higher than that in the non-habitats. The cluster analysis also clearly showed that habitats and non-habitats of Z. marina have distinct characteristics.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.7
• /
• pp.19-29
• /
• 2013

Analysis via classical soil mechanics theory is either ineffective or inappropriate for fully describing stress distribution or failure conditions in cold regions, since mechanical properties of soils in cold regions are different from those reported in the classical soil mechanics theory. Therefore, collecting and analyzing technical data, and systematic and specialized research for cold regions are required for design and construction of the structure in cold regions. Freezing and thawing repeat in active layer of permafrost region, and a loading condition affecting the structure changes. Therefore, the reliable analysis of mechanical properties of frozen soils according to various conditions is prerequisite for design and construction of the structure in cold regions, since mechanical properties of frozen soils are sensitive to temperature condition, water content, grain size, relative density, and loading rate. In this research, the direct shear apparatus which operates at 30 degrees below zero and large-scaled low temperature chamber are used for evaluating shear strength characteristics of frozen soils. Weathered granite soil is used to analyzed the shear strength characteristics with varying freezing temperature condition, vertical confining pressure, relative density, and water content. This research shows that the shear strength of weathered granite soil is sensitively affected by various conditions such as freezing temperature conditions, normal stresses, relative densities, and water contents.

• Journal of Sensor Science and Technology
• /
• v.2 no.1
• /
• pp.3-10
• /
• 1993

Polycrystalline CdS thin films were grown on ceramic substrate using a chemical bath deposition method. They were annealed at various temperature and X-ray diffraction patterns were measured by X-ray diffractometer in order to study CdS polycrystal structure. Using extrapolation method of X-ray diffraction patterns for the CdS samples annealed in $N_{2}$ gas at $550^{\circ}C$ it was found hexagonal structure whose lattice constants $a_{o}$ and $c_{o}$ were $4.1364{\AA}$ and $6.7129{\AA}$, respectively. Its grain size was about $0.35{\mu}m$. Hall effect on this sample was measured by Van der Pauw method and studied on carrier density and mobility defending on temperature. From Hall data, the mobility was likely to be decreased by piezo electric scattering at temperature range of 33K and 150k and by polar optical scattering at temperature range of 150K and 293K. We measured also spectral response, sensitivity (${\gamma}$), maximum allowable power dissipation and response time on these samples.