• Journal of the Korean Society for Heat Treatment
• /
• v.20 no.6
• /
• pp.293-298
• /
• 2007

Influences of aluminum carbide ($Al_4C_3$) addition on microstructure and damping capacity of Mg-3%Al casting alloy have been investigated based on experimental results of optical micrography, scanning electron microscopy with energy-dispersive spectrometry analysis and damping capacity measurement at RT. The addition of $Al_4C_3$ particles results in an efficient grain refinement. The damping capacity shows an increasing tendency with an increase in $Al_4C_3$ content. The damping value associated with $Al_4C_3$ particles is linearly dependent on the volume fraction of $Al_4C_3$ particles to the 2/3 power, $f_{2/3}$, which corresponds to the total surface area of the particles.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.179-182
• /
• 2000

The dynamic softening behavior of type 430 ferritic stainless steel could be characterized by the hot torsion test in the temperature range of 900-110$0^{\circ}C$ and the strain rate range of 0.05-5/sec. It is found that the continuous dynamic recrystallization (CDRX) was a major dynamic softening mechanism. The effects of process variables strain ($\varepsilon$) stain rate($\varepsilon$)and temperature (T) on CDRX could be individually established from the analysis of flow stress curves and microstructure. The effect of CDRX individually established from the analysis of flow stress curves and microstructure. The effect of CDRX increased with increasing strain rate and decreasing temperature in continuous deformation. The multipass deformation processes were performed with 10 pass deformations. The CDRX effect occurred in multipass deformatioon. The grain refinement could be achieved from multipass deformation The grain refinement increased with increasing strain rate and decreasing temperature. Also the CDRX in multipass deformation was affected by interpass time and pass strain. The total strain was to be found key parameter to occur CDRX.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.172-179
• /
• 1999

As the martensite structure cause fracture failure during drawing from 5.5mm rod to 3.05mm dia. wire without additional heat treatment, the optium cooling condition to inhibit the occurrence of martensite was investigated. In order to get SAE9254+V quality, the effects of alloying element, vanadium on the mechanical properties were investigated. Based upon CCT and TTT curves and the results form cooling test in mill, optimun cooling was found in the condition of the laying head temp of 780$^{\circ}C$ and of the conveyor speed at 0.15m/sec with the whole cover closed. The wire rods produced under the condition showed the best mechanical properties of 120kg/$\textrm{mm}^2$ in TS and 50% in RA, having an excellent drawability. In vanadium added steels, tensile strength was improved without degrading elongation and charpy impact value. That means the strengthening by vanadium is mainly due to the grain refinement by the fine precipitates during tempering process.

• Journal of Powder Materials
• /
• v.14 no.1 s.60
• /
• pp.50-55
• /
• 2007

The hydrogen sorption speeds of $Zr_{57}V_{36}Ti_7$ amorphous alloy and its crystallized alloys were evaluated at room temperature. $Zr_{57}V_{36}Ti_7$ amorphous alloy was prepared by ball milling. The hydrogen sorption rate of the partially crystallized alloy was higher than that of amorphous. The enhanced sorption rate of partially crystallized alloy was explained in terms of grain refinement that has been known to promote the diffusion into metallic bulk of the gases. The grain refinement could be obtained by crystallization of amorphous phase resulting in the observed increase in sorption property.

• Transactions of Materials Processing
• /
• v.6 no.2
• /
• pp.102-109
• /
• 1997

The multistage deformation and stress relaxation were carried out to investigate the strain induced precipitation by torsion tests in the range of 1000~80$0^{\circ}C$, 0.05~5/sec for V-microalloyed steel. The starting temperature and time for the initiation of precipitation were determined by stress relaxation tests. The distribution of precipitates increased, as the strain rate increased and the mean size of precipitates was found to be about 10~30nm. The precipitation starting time$(P_s)$ decreased with increasing strain rate and the amount of pre-strain. The effect of deformation conditions on the no-recrystallization temperature$(T_nr)$ was also determined in the multistage deformation. $T_nr$ Tnr decreased with increasing the strain and strain rate. In the controlled rolling simulation, grain refinement and precipitation hardening effects could be achieved by the alternative large pass strain at the latter half pass stage under the condition of low temperature and high strain rate.

• Journal of Mechanical Science and Technology
• /
• v.19 no.7
• /
• pp.1441-1448
• /
• 2005

Fine grained AZ31 and AZ61 magnesium alloys produced by equal channel angular pressing (ECAP) were tested for investigating tensile and fatigue properties, including microstructure, monotonic tensile flow, fatigue life and crack growth rate. For the two alloys, the yield stress of the ECAPed sample was lower than that of the unECAPed (=as received) sample, because of the fact that the softening effect due to texture anisotropy overwhelmed the strengthening effect due to grain refinement. Grain refinement of the AZ31 and AZ61 alloys through ECAP was found not to be significantly effective in increasing fatigue strength.

• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.3
• /
• pp.156-159
• /
• 2011

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1996.05a
• /
• pp.107-108
• /
• 1996

• Transactions of Materials Processing
• /
• v.13 no.7
• /
• pp.559-563
• /
• 2004

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.251-254
• /
• 2001

In this paper, the effect of grain refinement on room temperature ductility of copper was addressed. Recent experimental results have shown that this material, as well as a number of other single-phase metals that are ductile when coarse-grained, loose their ductility with decreasing grain size in the sub micrometer range. A recently developed model in which such materials are considered as effectively two-phase ones (with the grain boundaries treated as a linearly viscous second phase) was applied to analyze stability of Cu against ductile necking. As a basis, Hart's stability analysis that accounts for strain rate sensitivity effects was used. The results confirm the observed trend for reduction of ductility with decreasing grain size. The model can be applied to predicting the grain size dependence of ductility of other metallic materials as well.