• Asian-Australasian Journal of Animal Sciences
• /
• v.13 no.9
• /
• pp.1239-1244
• /
• 2000

In order to investigate the effect of incorporation of thermally processed cereal (maize) grain and differently degradable protein sources in the calf starter, twenty four newly born crossbred $(Bos\;taurus{\times}Bos\;indicus)$ calves were assigned at random to six diets in a $3{\times}2$ factorial design involving three protein sources viz. groundnut meal (GN), cottonseed meal (CS) and meat and bone meal (MB), each along with two differently processed grain, namely ground raw (R) and pressure cooked (P) maize. The corresponding calf starters with green oats (Avena sativa) were given free-choice from 14 d onwards till the end of the 90 d experimental feeding. A restricted milk diet was fed till the age of weaning at 60 d. Total DM intake was not affected by cereal or protein sources. However, daily intake of DM (59.23 vs 66.45 g) and CP (12.38 vs 14.10 g) per kg $W^{0.75}$ was reduced (p<0.05) due to cereal processing. Better (p<0.05) feed and protein efficiencies after weaning and during entire period in calves fed processed maize resulted in a trend of higher $(p{\leq}092)$ growth rate especially when GN was the source of protein. In comparison among protein sources, calves fed MB diets tended to grow faster $(p{\leq}098)$ concurrent with a higher CP intake before weaning. It is thus evident that thermal processing of maize in the calf starter seems to improve calf performance. Moreover, results indicated that feeding of protein and starch sources of matching ruminal degradability may prove beneficial for early growth of crossbred calves.

• Journal of the Korean Society for Railway
• /
• v.18 no.4
• /
• pp.354-362
• /
• 2015

Since allowable settlement of concrete slab track is about 30mm, a lot of attention must be paid to the settlement of the earthwork (reinforced trackbed, upper subgrade, under subgrade) under the concrete track. To this end, more experimental data should be accumulated through tests for these materials. In this study, we evaluate the long-term settlement of reinforced trackbed and subgrade materials using factors such as repeated loading conditions, water content, and grain size distributions in a large triaxial test and a large oedometer test. In cases in which the performance of the reinforced trackbed layer meets the design criteria, the settlement caused by train load was considerably small. But, when the water content increases in the subgrade, unexpectedly large settlement might occur for certain grain size distributions of the subgrade materials.

• Research in Plant Disease
• /
• v.29 no.2
• /
• pp.137-144
• /
• 2023

Exserohilum turcicum is a fungus that causes northern corn leaf blight (NCLB) and has deleterious effects on maize production globally. Therefore, it is prudent to mitigate the effects of NCLB using genetic diversity. The objective of this research was to assess the severity of NCLB disease on the growth and yield of various maize genotypes. A randomized complete block design field experiment, replicated three times, was conducted to evaluate the effect of E. turcicum on 10 maize hybrids. Percent disease index, plant height, and leaf area were recorded at the silk stage. Cob weight, grain fresh weight, and grain yields were determined at harvest maturity. All measured parameters were significantly different (P<0.05) between the maize hybrids. Of the 10 genotypes, four (PAN 4R-528R, PAN 4R-728BR, PAN 3R-724BR, and P1788BR) were susceptible, five (DKC74-74BR, PAN 5R-582R, PAN 5R-890R, PAN 5R-854R, and PAN 5R-590R) were moderately susceptible, and one (DKC80-40BR) was moderately resistant. DKC80-40BR exhibited greater cob weight, while DKC74-74BR was superior in all other plant growth and yield components. Interestingly, although not significant (P>0.05) and high, maize growth and yield parameters had negative correlations with disease incidence, except for grain fresh weight. Therefore, DKC80-40BR may be selected for cultivation in areas prone to NCLB to reduce maize susceptibility to the disease, while DKC74-74BR may improve crop performance. These hybrids could be considered as potential sources of resistance or tolerance to NCLB for further validation by plant breeders.

• The Research Journal of the Costume Culture
• /
• v.17 no.3
• /
• pp.472-483
• /
• 2009

The purpose of this study is to analyse the effects of knit samples' mechanical properties on changes of skirt length of knit flared skirt, and to compare it to the knitting method of a seamless knitted flare skirt. So, I compared the appearance and 3-dimensional shape of a seamless knitted flare skirt with those of a fully cut knit flared skirt. For this study, 18 kinds of cut and sew or seamless knitted test garment were made. The data analysis methods used in this study were descriptive statistics, one-way ANOVA, correlation analysis, and regression analysis. The results are as follows: The result of the evaluation of knit samples' mechanical properties by the KES-FB system showed that elongation decreased as gauge increased and course direction was greatest among grain directions. The length change after wearing the knitted flare skirts appeared wholly equal to the seamless knitted, compared with the cut and sew. The change was biggest at $180^{\circ}$, 7G of the cut and sew. In grain direction, bias cut showed more than 1.2cm of length change. As the weight and thickness increased, the length changes become larger. The regression analysis indicated that the greatest contributive variables on the length changes were elongation, weight, and thickness.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.1
• /
• pp.19-26
• /
• 2009

The response characteristics of $H_2O_2$ monopropellant thrusters at a pulse mode were presented in this paper. A catalyst bed was fixed to $MnO_2$/$Al_2O_3$ to investigate the thruster design effect to response time. Three different thrusters (50 N class) having different injectors, ullage volumes, catalyst grain sizes, and reactor volumes were prepared to investigate the response characteristics. As a result, the ignition delay, pressure rising and tail-off time of case 2-2 thruster with 16-20 mesh catalyst size were 14, 108, 94 ms respectively, which were comparable to requirement of response time at commercial hydrazine thrusters.

• The KSFM Journal of Fluid Machinery
• /
• v.3 no.4 s.9
• /
• pp.7-14
• /
• 2000

This paper provides integrity evaluation and root cause analysis for defects observed at volute tongue, or cutwater, of the operating centrifugal pump in power plant. The cause of the cracks are analyzed and reviewed from the viewpoint of the operation and maintenance of the pumps, and the sample obtained from the cracked volute tongue of the pump are examined. At first, in-situ hardness test and microstructure examination were performed to understand the cause of cracking at volute tongue. The evaluation of structural integrity and the possibility of the crack propagation is also evaluated. Cracks were typical intergranular cracking and propagated along with prior austenite grain boundary. At easing volute tongue, the hardness was higher than ASTM requirement and a large amount of intergranular Cr carbide was precipitated. These were due to high C content in material. P content was also higher than ASTM requirement. Therefore, Cr carbide precipitation and P segregation at grain boundary, caused by higher C and P content in material, resulted in intergranular cracking of casing volute tongue. This procedure for integrity evaluation and root cause analysis is used to guide, and support the pump designer and manufacturer's material selection and process design to avoid a costly, unplanned outage of plant.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.723-726
• /
• 2002

In this paper, a high efficiency leakage transformer for neon tube is developed to improve its power factor, to reduce its core loss and weight by using a technique of shape optimization and direction of grain-oriented silicon steel sheet. A protection circuit is designed for all types of neon transformer loaded with one or more neon lamps. Whenever the neon tube fails to be started up or comes to the life end, or encounters faults with open-circuits at the output terminals of the neon transformer, the protection circuit will be initiated to avoid more critical hazards. These neon transformers need a protection circuit to prevent from current stresses on circuit components by neon tube fail. The input of the transformer is automatically cut off when the abnormal condition occurs, preventing waste of no-load power. As the results of the study, the core weight is reduced by $11\%$, the power factor improved by $5\%$ and the efficiency increased by $6\%$ compared with the conventional type due to the employment of the grain-oriented steel sl)eel and the optimized core shape.

• Journal of Korea Foundry Society
• /
• v.32 no.1
• /
• pp.32-37
• /
• 2012

In this study, microstructural evaluation was carried out on secondary hardening type ultrahigh strength steel, Fe-Co-Ni composition. This paper as a first part of whole research presented the microstructural behavior by cyclic heat treatment. The cyclic heat treatment method includes normalizing, stress relieving, solution treatment and aging. Especially, solution treatments performed triple times to get maximized solution hardening. Phase transformation and microstructure were observed by using optical microscope (OM), Electron back-scattered diffraction (EBSD) and X-ray stress analyzer. During the triple solution treatment, size of grain boundary was dramatically decreased by generating a packet from the martensite transformation of residual austenite in the inner part of grain, whereas the hardness increase was not significant.

• Journal of Biosystems Engineering
• /
• v.6 no.1
• /
• pp.48-59
• /
• 1981

The major limiting factor on the determination of combine capacity is the frequent occurence of clogging over the some parts of machine when the crop is wet in the case of Japanese self-feeding type combine. And in the case of American conventional combine having big separating parts, the great grain loss and damage occur when the machine is used for rice harvesting. This experiment was carried out to develop the new type threshing and separating equipment. Proto-type thresher which consist of a conical threshing drum and a conical separating sieve rotating around the threshing cone was constructed and tested. In the case of 800 rpm of threshing cone speed, average threshing loss was below 1 percent, separating loss was about 1 percent, grain damage was about 0.4 percent, and average total power required was about 2.6 PS. This design has some problems such as higher power required or wrapping problems under the conditions of feeding long damp straw. But, compared with the conventional combine or thresher, this machine certainly has some potentials for this approach to combine development. The crop feed rate must be increased through improvement of the feeding portion of the threshing cone. And it is required to investigate further about some parameters causing wrapping phenomena.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.5
• /
• pp.391-398
• /
• 2010

In this study, the figure of domestic hardwood was observed using the naked eye and the possibility of substituting imported wood with domestic one in the making woodcraft or furniture was investigated. It was known from the investigation on 8 different hardwoods that there were various figures such as cloud-shaped figure, blister figure, crotch figure, bird's eye figure, etc. in Zelkova serrata wood and the beautiful pigment figure in Diospyros Kaki wood. There were the unusual figures such as wavy grain figure, fiddle back figure, etc. in Cedrela sinensis wood and was clear ray-fleck figure in Quercus variabilis wood. There were also various figures such as wavy grain figure, blister figure, pigment figure, etc. in Sophra japonica, Tilia amurensis, Castanea crenata, Kalopanax septemlobus wood, etc. It is thus that distinguished figures appeared in each kind of wood can be used for craft, sculpture, furniture, and interior material. These kinds of figures can also be used for instrument, toy, stationery, life article material and souvenir, etc. And it can be expected that they will replace the imported wood has been mainly used to make the woodcraft or furniture until now.