• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.946-953
• /
• 1996

The effect of absorbed dose, dose rate, cationic salts and solvent on the grafting yield was evaluated when acrylic acid was grafted onto polypropylene fabric by simultaneous irradiation process. Low dose rate when irradiated with the same absorbed dose led to a high grafting yield. On the other hand, the grafting yield increased with dose rate in case the total irradiation times is equal, and the initial rate of grafting was found to be proportional to be 0.74 power of dose rate. $FeSO_4{\cdot}7H_2O$ was found to be the most effective additive for high grafting yield, while inhibiting homopolymer formation. It was impossible to induce radiation grafting without the addition of the certain amount of salt, but the grafting yield decreased with increasing metallic salt.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.938-945
• /
• 1996

The present studies are to describe the grafting reaction of styrene in various solvents to polypropylene fabric by the simultaneous method using Co-60. The influence of various factors such as absorbed dose, dose rate, type of solvent, acid and multifunctional monomer were evaluated. At constant absorbed dose, the grafting yield was found to be higher at low dose rate. The initial rate of grafting was found to be proportional to a 0.56 power of dose rate. The inclusion of mineral acid in the grafting solution led to an increase in radiation grafting yield at almost all monomer concentration examined. Multifunctional monomer was also effective to increase grafting yield. The addition of both acid and multifunctional monomer was found to accelerate the grafting yield much more than the separate addition of two additives.

• Journal of Periodontal and Implant Science
• /
• v.47 no.6
• /
• pp.388-401
• /
• 2017

Purpose: The physicochemical properties of a xenograft are very important because they strongly influence the bone regeneration capabilities of the graft material. Even though porcine xenografts have many advantages, only a few porcine xenografts are commercially available, and most of their physicochemical characteristics have yet to be reported. Thus, in this work we aimed to investigate the physicochemical characteristics of a porcine bone grafting material and compare them with those of 2 commercially available bovine xenografts to assess the potential of xenogenic porcine bone graft materials for dental applications. Methods: We used various characterization techniques, such as scanning electron microscopy, the Brunauer-Emmett-Teller adsorption method, atomic force microscopy, Fourier-transform infrared spectroscopy, X-ray diffraction, and others, to compare the physicochemical properties of xenografts of different origins. Results: The porcine bone grafting material had relatively high porosity (78.4%) and a large average specific surface area (SSA; $69.9m^2/g$), with high surface roughness (10-point average roughness, $4.47{\mu}m$) and sub-100-nm hydroxyapatite crystals on the surface. Moreover, this material presented a significant fraction of sub-100-nm pores, with negligible amounts of residual organic substances. Apart from some minor differences, the overall characteristics of the porcine bone grafting material were very similar to those of one of the bovine bone grafting material. However, many of these morphostructural properties were significantly different from the other bovine bone grafting material, which exhibited relatively smooth surface morphology with a porosity of 62.0% and an average SSA of $0.5m^2/g$. Conclusions: Considering that both bovine bone grafting materials have been successfully used in oral surgery applications in the last few decades, this work shows that the porcinederived grafting material possesses most of the key physiochemical characteristics required for its application as a highly efficient xenograft material for bone replacement.

• Journal of Korean Society of Forest Science
• /
• v.26 no.1
• /
• pp.49-55
• /
• 1975

This study was carried out to find out the proper method of grafting of Magnolia grandiflora L. Magnolia kobus DC. was used as stocks and the modified veneer grafting method in which a flap was attached to the cut surface of scion was adopted. And also the environment of the grafting beds was controlled for giving optimum humidity (90-100%) and temperature ($20-25^{\circ}C$). The results are summarized as follows: 1. Two year-old seedlings of M. kobus were best as stocks for grafting of M. gantiflora. 2. The modified veneer grafting which brought the successful result of 43 to 89.5 percent found to be very efficient method. 3. The environmental control made of vinyl tunnel and screen (lath) was very effective to attain to the excellent result of 89 percent. 4. For scions, one to two year-old branches with well developed winter buds collected just before the time of grafting gave the best results. 5. The optimum season for grafting in Kwangju districts was 15 to 20, April.

• Journal of the Korean Chemical Society
• /
• v.20 no.4
• /
• pp.299-308
• /
• 1976

Cerium (Ⅳ) ion-initiated graft copolymerizations of acrylamide and of acrylonitirile to silk fibroins were investigated. When acrylamide was used, the change in ceric ammonium nitrate concentration exhibited a maximum in degree of grafting at 0.01 M. Also observed was that the change in acetic acid content in reaction media gave a maximum in degree of grafting at 7% acetic acid in water. Degree of grafting was increased generally with increase in acrylamide concentration reaction time and reaction temperature. When acrylonitrile monomer was used for grafting,different results were obtained. Addition of nitric acid was more effective in enhancing the degree of grafting than the addition of acetic acid.Generally the grafting of acrylonitrile to silk fibroins was less efficient than the grafting of acrylamide. The portion of grafted silk fibroins insoluble in Lowe's reagent exhibited the IR absorption bands characteristics to both vinyl polymers and silk fibroins, indicating the grafting of vinyl monomers to silk fibroins. To examine the molecular weight of graft vinyl polymer, a sample of grafted silk was hydrolyzed by 10% sodium hydroxide. Viscosity measurements indicated that the molecular weight of the graft polymer was in the range of 105.

• Journal of the Korean Ceramic Society
• /
• v.53 no.1
• /
• pp.24-33
• /
• 2016

The grafting reaction for maleic anhydride (MA) onto high density polyethylene (HDPE) was investigated from solution process with initiators. The chemical modification of neat HDPE was carried out with various contents of MA (3-21 wt.%) and initiator (0.2-1 wt.%) at different temperature ($80-130^{\circ}C$). The grafting degree was obtained from the titration and the highest grafting degree was 3.1%. The grafting degree increased as the content of MA and initiator increased, however, the highest grafting degree was demonstrated for a particular content of MA and initiator. In the non-isothermal crystallization kinetics, the Ozawa model was unsuitable method to investigate the crystallization behavior of MA onto HDPE, whereas the Avrami and Liu models found effective. The crystallization rate was accelerated as the cooling rate increased, but postponed by combination of MA onto neat HDPE backbone.

• Archives of Plastic Surgery
• /
• v.38 no.3
• /
• pp.222-227
• /
• 2011

Purpose: Autogenous particulate bone grafting is a type of autogenous bone graft that consists of small particles of cortical and cancellous bone. Autogenous particulate bone grafting has been used for calvarial bone defect after calvarial defect of craniosynostosis and prevention of temporal depression after fronto-orbital advancement. The results were followed up and studied for effectiveness of autogenous calvarial particulate bone grafting. Methods: Cranial vault remodeling and fronto-orbital advancement was performed for six craniosynostosis patient from August 2005 to October 2007. Autogenous particulate bone grafting was harvested from endocortex of separated cranial vault and if insufficient, from extocortex of occipital region using Hudson brace & D'Errico craniotomy bit and was grafted on the calvarial bone defect of cranial vault and temporal hollow. Fibrin glues were added to the harvested particulated bone for adherence and shaping of paticles. Results: Autogenous particulate bone grafting was followed-up at least longer than I year. The calvarial bony defects following primary cranial remodeling were successfully covered and postoperative temporal depressions after fronto-orbital advancement were also well prevented by grafted particulated bone. Conclusion: Autogenous calvarial particulate bone graft can be harvested in infants and young children with minimal donor site morbidity. It effectively heals cranial defects in children and during fronto-orbital advancement reduces the prevalence of osseous defects independent of patient age. It's easy and effective method of reconstruction of calvarial defect.

• Journal of Bio-Environment Control
• /
• v.23 no.4
• /
• pp.364-370
• /
• 2014

The nutrient and irrigation management of scion and rootstock can alleviate stress on grafted transplants after grafting and promote the growth. This study investigated the effects of nutrient and irrigation management of scion and rootstock on the graft-take and growth of grafted pepper transplants. Before grafting, the scions were subjected to different water potential regimes in media by controlling the irrigation frequency and time. The scions were subirrigated 0, 1(two days before grafting), 1(one days before grafting) or 2 times for five days before grafting. The irrigation frequency and time influenced the water potential of media and the growth of scion and grafted transplants. At 13 days after grafting, fresh and dry weight of transplants which were irrigated once at two days before grafting were greater by 29 and 34% than those without irrigation during five days before grafting. This suggests that mild water stress on scion prior to grafting by controlling water management alleviate water stress on grafted transplants after grafting and improve the growth. Before grafting, the rootstocks were subjected to different nutrient regimes by controlling nutrient solution application. The rootstocks were supplied with nutrient solution 0, 1, 2, or 4 times. The nutrient application frequency and time influenced the electrical conductivity (EC) and pH of media. Accordingly, the growth and mineral contents of rootstock and grafted transplants were also affected. At 13 days after grafting, fresh and dry weight of transplants with four times of nutrient application increased by 30 and 20%, respectively, than those without nutrient solution supply during seven days before grafting. Therefore, it is recommended that nutrient solution be supplied more than four times during seven days before grafting for the production of high quality transplants.

• Applied Chemistry for Engineering
• /
• v.7 no.1
• /
• pp.75-82
• /
• 1996

Acrylic acid was graft-copolymerized on polyethylene film in the presence of additives such as acid and $FeSO_4(NH_4)_2SO_4{\cdot}6H_2O$ using peroxide grafting technique by ${\gamma}$-ray and electron beam, and the effect of $FeSO_4(NH_4)_2SO_4{\cdot}6H_2O$ and acid on the grafting yield was evaluated. The grafting mechanism and the physical property of grafted films were also examined. The results showed that the inclusion of $FeSO_4(NH_4)_2SO_4{\cdot}6H_2O$ in acidified acrylic acid grafting solution was extremely beneficial and led to a most unusual enhancement effect in the radiation grafting. In the other hand, inclusion of mineral acid in the grafting solution in the absence of $FeSO_4(NH_4)_2SO_4{\cdot}6H_2O$ could not lead to he suitable grafting reaction by the severe homopolymerization of acrylic acid. The addition of $H_2SO_4$, and HCl led to much higher grafting yield than $HNO_3$and $CH_3COOH$. It was shown that grafting yield of ${\gamma}$-ray irradiated-polyethylene was higher than that of electron beam irradiated polyethylene.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.04a
• /
• pp.99-101
• /
• 1998

1. Introduction : The conventional grafting polymerization technique requires chemically reactive groups on the surface as well as on the polymer chains. For this reason, a series of prefunctionalization steps are necessary for covalent grafting. The surface prefunctionalizational technique for grafting can be used to ionization radiation, UV, plasma, ion beam or chemical initiators. Of these techniques, radiation method is one of the useful methods because of uniform and rapid creation of active radical sites without catalytic contamination in grafted samples. If the diffusion of monomer into polymer is large enough to come to the inside of polymer substrate, a homogeneous and uniform grafting reaction can be carried out throughout the whole polymer substrate. Radiation-induced grafting method may attach specific functional moieties to a polymeric substrate, such as preirradiation and simultaneous irradiation. The former is irradiated at backbone polymer in vacuum or nitrogen gas and air, and then subsequent monomer grafting by trapped or peroxy radicals, while the latter is irradiated at backbone polymer in the presence of the monomer. Therefore, radiation-induced polymerization can be used to modification of the chemical and physical properties of the polymeric materials and has attracted considerable interest because it imparts desirable properties such as blood compatibility. membrane quality, ion excahnge, dyeability, protein adsorption, and immobilization of bioactive materials. Synthesizing biocompatible materials by radiation method such as preirradiation or simultaneous irradiation has often used $\gamma$-rays to graft hydrophilic monomers onto hydrophobic polymer substrates. In this work, in attempt to produce surfaces that show low levels of anti-fouling of bovine serum albumin(BSA) solutions, hydroxyethyl methacrylate(HEMA) was grafted polypropylene membrane surfaces by preirradiation technique. The anti-fouling effect of the polypropylene membrane after grafting was examined by permeation BSA solution.