• Transactions on Electrical and Electronic Materials
• /
• v.4 no.4
• /
• pp.22-25
• /
• 2003

High series resistance due to the presence of glass frit is one of the major problems for screen printed silicon solar cells. Cells having electrical parameters below the prescribed values are usually rejected during solar module fabrication. Therefore, it is highly desirable to improve the electrical parameters of the silicon solar cells and thereby to increase the overall production yield. It was observed that, the performance of low quality mono-crystalline silicon solar cells made by standard screen printing technology could be improved remarkably by novel surface treatment. We have chemically treated the surface using sodium hydroxide (NaOH) and silver nitrate ($AgNO_3$) solutions. NaOH treatment helps to reduce the series resistance by decreasing the presence of excess glass frit on the top silver grid contact. The $AgNO_3$ treatment is used to reduce the series resistance comes from the deposition of silver on the grids by filling the holes present (if any) within the grid pattern.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.12
• /
• pp.1111-1116
• /
• 2005

ZnO varistor ceramics added a glass-frit 0.03 $wt\%$ were fabricated with variation of sintering temperature. The sintering temperature and time were $1125^{\circ}C\~1200^{\circ}C$ and 2 h. The average grain sizes increased and the varistor voltage decreased with increasing the sintering temperature. The values of the specimen sintered at $1200^{\circ}C$ were $23.7\;{\mu}m$ and 329 V, respectively. The leakage current of all specimens was less than $1\;{\mu}A$ at DC $82\%$ of varistor voltage. The clamping voltage ratio of the specimen sintered at $1175^{\circ}C$ was 1.37. The endurance of surge current and the deviation of varistor voltage of the specimen sintered at $1175^{\circ}C$ were 6400 $A/cm^2$ and ${\Delta}-2.81\%$, respectively. After the High Temperature Load Test(HTLT) at $85^{\circ}C$ for 1000 h, the specimen sintered at $1175^{\circ}C$ showed the lowest deviation of varistor voltage of ${\Delta}-1.92\%$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05a
• /
• pp.185-188
• /
• 2004

A diode structure of field emission lamps based upon carbon-nanotube is studied. The single-walled carbon nanotubes(SWNTs) were produced by arc discharge method. We made the 1-inch diode type flat lamp using CNTs. We applied anode voltage gradually to refine the field emission behavior of emitter in dynamic vacuum system to study the emission current. the brightness and efficiency, etc. The field emission properties was estimated by varying gaps between the cathode and anode, contents of the glass frit. The good luminous efficiency is showed in the gap $900{\mu}m$, $1200{\mu}m$ and contents of the proper glass frit. For the upper conditions, the luminous efficiencies were respectively 23.30, 11.12 1m/W.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.2
• /
• pp.144-150
• /
• 2013

A New Ag-pastes were developed for integrating the high efficiency mono-Si solar cell. The pastes were the mixture of 84 wt% Ag, 2 wt% glass frit, 11 wt% solvent of buthyl cabitol acetate, and 3 wt% additives. After fabricating the Ag-pastes by using a 3-roll mill, they were coated on a $SiN_x$/n+/p- stacks of a commercial mono-Si solar cell. And the post-thermal process was also optimized by varying the process conditions of peak temperature. The optimized solar cell efficiency on a 6-inch mono-Si wafer was 18.28%, which was the one of the world best performances. It meaned that the newly developed Ag-paste could be adopted to fabricate a commercial bulk Si solar cell.

• Electrical & Electronic Materials
• /
• v.9 no.7
• /
• pp.652-659
• /
• 1996

Sintering characteristics and electrical properties of xPb(Mg$_{1}$8/Te$_{1}$8/Mn$_{1}$4/Nb$_{1}$2/) $O_{3}$-(1-x) Pb (Zr$_{1}$2/ $Ti_{1}$2/) $O_{3}$ (x=0.075, 0.1, 0.125) ceramics are investigated. A sintering temperature of ceramics could be reduced to 950.deg. C by a reaction between PbO and B site compound material. The physical properties of 0.1Pb(Mg, Te, Mn, Nb) $O_{3}$ - 0.9Pb(Zr, Ti) $O_{3}$ bulk ceramic with 3wt% glass frit(0.857PbO-0.143W $O_{3}$) were following : den = 7.95 g/cm$^{3}$, T$_{c}$=340.deg. C, .epsilon.$_{33}$= 754, k$_{31}$=0.3 and Q.=1780. The 3-layer piezoelectric transformer by using a tape casting method showed a good monolithic structure, and its voltage setup ratio was 2.5 times higher than that of a single device by using bulk ceramics.s.s.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.307-308
• /
• 2005

ZnO varistor ceramics were fabricated as a function of the sintering temperature from $1125^{\circ}C$ to $1200^{\circ}C$ with glass-frit 0.03wt% addition. The average grain size was increased from 10.4 ${\mu}m$ to 23.7 ${\mu}m$, and varistor voltage was decreased from 538 V to 329 V with rising of the sintering temperature. The nonlinear coefficient a showed similar value from 75 to 80 and leakage current of all specimens exhibited the result of $1{\mu}A$ at 82% of varistor voltage. But the clamping voltage ratio of the specimens sintered at $1175^{\circ}C$ was 1.37 at 25A [$8/20{\mu}s$]. Also, endurance of surge current and deviation of varistor voltage of sintered specimens at $1175^{\circ}C$ were $6400A/cm^2$, $\Delta$-3.32%, respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.4
• /
• pp.575-585
• /
• 2013

This research was performed to evaluate the recycling feasibility as a construction material of dredged harbor soil mixed with clay and glass frit. Concentration of heavy metals of the dredged soil from D harbor was severly high, showing Zn of 526.0~13,150.1 mg/kg. The dredged soil was maily composed of 48.30 wt% $SiO_2$, 16.60 wt% $Al_2O_3$, 10.10 wt% CaO, 7.75 wt% $Fe_2O_3$. The clay and the glass frit contained 70.82 wt% $SiO_2$ and $Al_2O_3$ 18.78 wt%, and 71.75 wt% $SiO_2$, 13.99 wt% CaO, 8.51 wt% $Na_2O$, respectively. After adding 10~40 wt% to the clay and sintering them at $1,000^{\circ}C$ or $1,100^{\circ}C$, the compressive strength of the sintered specimens showed $132.6{\sim}178.5kgf/cm^2$ or $581.2{\sim}793.7kgf/cm^2$, respectively. In case of SC46 with the addition 40 wt% of the dredged soil to the clay, the compressive strength ($793.7kgf/cm^2$) of specimen sintered at $1,100^{\circ}C$ was over 5 times higher than that at $1,000^{\circ}C$. The specimen mixed with 40 wt% of dredged soil, 60 wt% of clay and 1 wt% of glass frit satisfied the 1st grade standard for clay brick by KS L 4201. The results of all specimens by Korean Standard Leaching Test also satisfied the standard criteria.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.898-901
• /
• 2006

To fabricate mono layer green sheet (MLGS) of transparent dielectric for PDP front panel, dispersion of transparent dielectric slurry and various properties of green sheets were examined as a function of amount and kinds of organic additives. Sedimentation height and viscosity of slurry were measured to determine proper types and amount of dispersant in non-aqueous system transparent dielectric slurry. Many MLGS having various ratios of the transparent dielectric glass frit, binder and plasticizer were fabricated. Finally we got the transparent dielectric layer of high transparency and free from residual pore might be remained in the gap between the electrodes.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.814-817
• /
• 2003

The sintering behavior of $BaO-B_{2}O_{3}-ZnO$, which is Pb-free glass-ceramic system, was examined as functions of the composition and the amount and particle size of $Al_{2}O_{3}$ filler. Different kinds of modifiers were added and $Al_{2}O_{3}$ fillers with different particle sizes ($1.5{\mu}m$ and $4.5{\mu}m$) were added. The glass frit-filler composites were sintered in the temperature range $520{\sim}580^{\circ}C$. X-ray diffraction results revealed that some of the composites crystallized during sintering. Dielectric constant and thermal expansion coefficient the glass-ceramics were analyzed.

• Laser Solutions
• /
• v.11 no.3
• /
• pp.10-15
• /
• 2008

This study is aimed to analyse the laser glass bonding process numerically. Due to the viscoelastic behaviour of glass, the extremely large deformation of the frit seal is resulted continuously over the transition temperature, so that the thermal boundary condition be changed in the entire calculation process. The commercial FEM algorithm is restrictively able to remesh the large geometrical boundary shape and to adapt the boundary conditions simultaneously. According to our manual adaptation of increasing the laser line intensity to 700 mW/mm, it is possible to estimate the thermal glass bonding process under the fracture stress in principle. But it should be studied further in the case of high laser line intensity.