• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.221-225
• /
• 2009

A solar thermal collector is a solar collector specifically intended to collect heat: that is, to absorb sunlight to provide heat. A flat plate is the most common type of solar thermal collector, and is usually used as a solar hot water panel to generate solar hot water. A flat plate collector consists basically of an insulated metal box with a glass or a plastic cover and a dark-colored copper absorber plate. Solar radiation is absorbed by the copper absorber plate and transferred to water that circulates through the collector in copper tubes. Ultrasonic welding is an industrial technique whereby high-frequency ultrasonic acoustic vibrations are locally applied to work pieces being held together under pressure to create a solid-state weld. In this study, we developed solar collector ultrasonic welding machine with digital controlled power supply and tested various welding conditions such as welding pressure, welding amplitude, welding speed. Welding speed was considered in 2~12m/min. The width of ultrasonic welds was increased with welding amplitude by 2.2~2.5mm. The fracture load of ultrasonic welds showed 20% higher than domestic products.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.2
• /
• pp.57-60
• /
• 2018

Recently, Thin-film transistors (TFTs) are fundamental building blocks for state-of-the-art microelectronics, such as flat-panel displays and system-on-glass. Zinc oxide thin films have the advantage that they can grow at low temperature and can obtain high charge movility. Also the zinc oxide thin film can be used to control the resistance according to the oxygen content, so it is very easy to obtain the desired physical properties. In this paper, we fabricated a zinc oxide thin film on a polished copper substrate through a solution process, then improved the crystallinity through a geat treatment porcess, and studied to transfer it on a flexible substrate after the heat treatment was completed.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.3
• /
• pp.10-16
• /
• 2018

In silicon crystalline PV (Photo Voltaic) industry, PV module or panel electric power is directly related to the companies' profit. Thus, many PV companies have invested and focused on R&D activities to get the higher module power. The main BOM (Bills of Material) on the module consists of PV solar cell, ribbon, EVA (Ethylene-Vinyl Acetate copolymer), glass and back sheet. Based on consistent research efforts on enhancing module power using BOM, there have been increase of around 5 watt per module every year as results. However, there are lack of studies related to enhancing accuracy of measurement. In this study, the enhancing on the metrology is investigated and the improvement shows actually contribution to company's profit. Especially, the measurement issues related to heat and to quasi state of bandgap diagram by EL(Electro Luminescence) are described in this study.

• Journal of the Korean Ceramic Society
• /
• v.39 no.3
• /
• pp.226-232
• /
• 2002

We searched thermal stability of ${\alpha}-Fe_2O_3$ using red color filter for display. In the PDP(Plasma Display Panel), the color filter layer is lied normally between front glass and transparent dielectric materials, so it might be needed to study the reaction of ${\alpha}-Fe_2O_3$ and transparent dielectric materials. The transparent dielectric materials containing ZnO has good transparency. Red colorlayer of ${\alpha}-Fe_2O_3$ contacted with dielectric material layer containing ZnO is changed to colorlessness over 500$^{\circ}$C because ZnO defuse ${\alpha}-Fe_2O_3$, the dielectric materials without ZnO, however, maintain red color at the same condition. We suggest that a layer contacting with ${\alpha}-Fe_2O_3$ red color layer has to lie with transparent dielectric materials without ZnO, then the materials containing ZnO is coated over to get color of ${\alpha}-Fe_2O_3$ for red color filter

• Journal of the Korean Society of Food Culture
• /
• v.7 no.4
• /
• pp.297-301
• /
• 1992

To investigate effects of the surface finishing methods (A : conventional press stone, B : enclosing in polyethylene (PE) bag, C : press-tone wrapped with PE film and D : covered with Chinese cabbage leaves 4cm in thickness on Kimchi) on Kimchi quality, pH-values, redness, film forming yeast growth, hardness and sensory quality of Kimchi during storage (for 60 days, at $10{\pm}5^{\circ}C$) in glass vessel $(11{\times}30cm)$ were investigated. pH of the top layer of A, C and D sample were higher than the optimum pH (4.2) of Kimchi, film forming yeast occurred on the surface of Kimchi, color of top layer Kimchi juice was darkened, and panel score of freshness and firmness was significantly worse (p<0.01) than that of sample B. However, in the case of Kimchi stored in PE bag (B), film forming yeast were can't detected visually in the surface of Kimchi, pH values were low as good quality Kimchi, freshness and firmness panel scores and hardness were significantly better (p<0.01) than A, C and D, and redness of juice of top layer of B was also preserved clearly for 60 days. Accordingly among the four surface finishing methods, the B-method was most effective in preserving of y of Kimchi.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.1
• /
• pp.186-193
• /
• 2009

In this paper, we adopted E-MOLD patent technology in order to fabricate Prismless LGP(Light Guide Panel) fur cellular phone and estimate the transcription of injection-molded parts. Then, we manufactured the Ni stamper fur Prismless LGP using MEMS process. And the stamper was installed in the movable heated core which is the key part of a patented mold. Using this mold, we manufactured injection-molded plastic LGP parts with different mold temperatures so that we investigate effect of the temperature on the transcription of the parts. The CAE analysis was also conducted in order to compare with the experimental results. The transcription of LGP parts with various mold temperature displayed $100^{\circ}C$(25.0nm), $140^{\circ}C$(48.4nm), $180^{\circ}C$(52.1nm) and when compared with stamper(521Inm), transcription was superior at $180^{\circ}C$. According to the CAE results, moldability was improved as mold temperature ($50^{\circ}C{\sim}180^{\circ}C$) increased, but when filling time($1{\sim}2sec$) increases, it decreased at $160^{\circ}C$. And transcription and moldability were improved markedly at glass transition temperature($140^{\circ}C$).

• Journal of the Korea Concrete Institute
• /
• v.26 no.4
• /
• pp.421-428
• /
• 2014

This paper describes the experimental results of insulated concrete sandwich wall panels (CSWP) with corrugated glass fiber-reinforced polymer (GFRP) shear connectors under in-plane shear loading. Corrugated GFRP shear connectors were used to improve the thermal property of insulated CSWP and to achieve composite action between the interior and exterior concrete wall panels. Test specimens were consist of three concrete panels with two insulation layers between concrete panels and middle concrete panels was loaded in the direction of gravity. To evaluate the effects of insulation types (extruded polystyrene, XPSS and expanded polystyrene, EPS), shear connector pitch (300 and 400 mm) and width (10 and 15 mm) on in-plane shear behavior of insulted CSWP, failure mode and shear flow-average relative slip relationship of specimens were investigated. Test results indicate that the bond stress between concrete panel and insulation is considerable initially. Especially in case of insulated CSWP without shear connector, initial stiffness of CSWP with XPSS is superior to that of CSWP with EPS. The shear connector's contribution to in-plane shear performance of insulated CSWP depends on the type of insulation.

• Composites Research
• /
• v.12 no.6
• /
• pp.74-82
• /
• 1999

The static and fatigue characteristics of polyurethane foam cored sandwich structures are investigated. Three types of the specimens with the glass fabric faces and the polyurethane foam core are used; non-stitched. stitched, and stiffened sandwich specimen. Especially additional structural reinforcements with the twisted polyester and glass fiber for thickness direction are made to stitched sandwich structure panel to minimize the delamination of structure which is stitched the upper and lower faces through the core and the resin is impregnated Into stitched fiber with the characteristics of low viscosity of resin at resin flow temperature and cured together with during the curing process. Bending strength of stitched specimen which is 50 mm $50{\times}50{\;}mm$ pitched is improved by 50 % as com-pared with non-stitched specimen and stiffened specimen is improved 10 times more than non-stitched structure. After fatigue testing of $10^6$cycles by 20% of ultimate load under monotonic load, the bending fatigue strength of non-stitched specimen is decreased by 27% of monotonic bending strength, 39% for stitched structure and 20% for stiffened specimen. To verify the aging effect of polyurethane form core, Ultrasonic C-scanning equipment is used to detect the damage of skin laminate alone after fatigue test. From results of UT C-scan images, there is no defect that can be damaged occurred during fatigue test. It is concluded that the decrease of bending strength for foam cored sandwich specimen is caused by the decrease of stiffness due to the aging of polyurethane foam core during fatigue cycles.

• Journal of the Korean Vacuum Society
• /
• v.12 no.3
• /
• pp.168-173
• /
• 2003

Recently, according to the rapid progress in Flat-panel-display industry, there has been a growing interest in the poly-Si process. Compared with a-Si, poly-Si offers significantly high carrier mobility, so it has many advantages to high response rate in Thin Film Transistors (TFT's). We have investigated a new process for the high temperature Solid Phase Crystallization (SPC) of a-Si films without any damages on glass substrates using thin film heater. because the thin film heater annealing method is a very rapid thermal process, it has very low thermal budget compared to the conventional furnace annealing. therefore it has some characteristics such as selective area crystallization, high temperature annealing using glass substrates. A 500 $\AA$-thick a-Si film was crystallized by the heat transferred from the resistively heated thin film heaters through $SiO_2$ intermediate layer. a 1000 $\AA$-thick $TiSi_2$ thin film confined to have 15 $\textrm{mm}^{-1}$ length and various line width from 200 to 400 $\mu\textrm{m}$ was used as the thin film heater. By this method, we successfully crystallized 500 $\AA$-thick a-Si thin films at a high temperature estimated above $850^{\circ}C$ in a few seconds without any thermal deformation of g1ass substrates. These surprising results were due to the very small thermal budget of the thin film heaters and rapid thermal behavior such as fast heating and cooling. Moreover, we investigated the time dependency of the SPC of a-Si films by observing the crystallization phenomena at every 20 seconds during annealing process. We suggests the individual managements of nucleation and grain growth steps of poly-Si in SPC of a-Si with the precise control of annealing temperature. In conclusion, we show the SPC of a-Si by the thin film heaters and many advantages of the thin film heater annealing over other processes

• Polymer(Korea)
• /
• v.38 no.5
• /
• pp.640-644
• /
• 2014

As a process of plat panel display production, slot coating is widely used for the coating of photoresist on a wide glass substrate. A uniform coating thickness is important, and the coating uniformity is divided into nozzle and machine directions. The machine and nozzle directions coating uniformities are influenced by the operation condition of coater and flow uniformity inside the die, respectively. Non-uniform coating during steady coating process occurs according to those factors, however, non-uniform coating along the machine and nozzle directions has been observed at the beginning of coating by unsteady flow. In this study, steady and unsteady state flow simulations have been performed and compared with experiment to examine the causes of non-uniform coating. Computational results exhibited that it took a time to get a uniform pressure distribution at whole inside the die, and during this period of time edge regions showed lower exit velocity compared with center region. Subsequently edge regions had thinner coated layers than center region. However edge regions showed higher exit velocity than center region after steady state, and this made edge regions had thicker coated layer than center region.