• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.876-879
• /
• 2003

The principal problems in development of dielectric paste materials for PDP(plasma display panel)are PbO free paste and low melting temperature. We prepared PbO free paste from glasses in the system $BaO-ZnO-B_2O_3-V_2O_5$. DTA, XRD and SEM were used to study and characterize $BaO-ZnO-B_2O_3-V_2O_5$ glasses. PbO free paste developed at this paper has thermal expansion of $74{\times}10^{-7}/^{\circ}C$, DTA transformation point of $460^{\circ}C$, and firing condition of $560^{\circ}C$, 10min.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.356-356
• /
• 2010

In this paper, Poly silicon thin-film transistors (poly-Si TFTs) with employed the SPC (Solid phase crystallization) and ELA (Excimer laser annealing) methods on glass panel substrate are fabricated to investigate the electrical poperies. Poly-Si TFTs have recess-channel structure with formated source/drain regions by LPCVD n+ poly Si in low $650^{\circ}C$ temperature. the ELA-TFT show higher on/off current ratio and subthreshold swing than a-Si and SPC TFT that therefore, these results showed that the ELA-TFT might be beneficial for practical embedded TFT memory device application.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1407-1411
• /
• 2003

Due to the heat confinement in the shallow region of the target for a short time scale, pulsed laser annealing has received increasing interest for the fabrication of poly-Si thin film transistors(TFTs) on glass as a low cost substrate in the flat panel displays. The formation and growth mechanisms of poly silicon(poly-Si) grains in thin films are investigated using an excimer laser crystallization system. To understand the crystallization mechanism, the grain formations are observed by FESEM analysis. The optical reflectance and transmittance during the crystallization process are measured using HeNe laser optics. A two-step ELC(Excimer Laser Crystallization) process is applied to enhance the grain formation uniformity.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.1
• /
• pp.64-71
• /
• 2009

In this paper, a study on low-velocity impact response of honeycomb sandwich panels was done for the changes of impact location and core fabrication angles. The test specimens were made of glass/epoxy laminate facesheet and aluminum honeycomb core. Square samples of 100mm and 100mm sides were subjected under low-velocity impact loading using instrumented testing machine at three energy levels. Impact parameters like maximum force, time to maximum force, deflection at maximum force and absorbed energy were evaluated and compared for the changes of impact location and core fabrication angle. The impact damage size were measured at facesheet surface by 3-Dimensional scanner. Also, sandwich specimens after impact test were cut to analyse the failure mode.

• Laser Solutions
• /
• v.6 no.2
• /
• pp.9-17
• /
• 2003

Due to the heat confinement in the shallow region of the target for a short time scale, pulsed laser annealing has received an increasing interest for the fabrication of poly-Si thin film transistors(TFTs) on glass as a low cost substrate in the flat panel displays. The formation and growth mechanisms of poly silicon(poly-Si) grains in thin films are investigated using an excimer laser crystallization system. To understand the crystallization mechanism, the grain formations are observed by FESEM photography. The optical reflectance and transmittance during the crystallization process are measured using HeNe laser optics. A two-step ELC(Excimer Laser Crystallization) process is applied to enhance the grain formation uniformity.

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.4
• /
• pp.71-76
• /
• 2009

The clean non-contact type conveyor system for vertical transfer of large size FPD(Flat Panel Display) glasses has been installed at FPD production line just since a few years ago. The most important part of the conveyor is the 3 axis permanent magnet rollers faced orthogonally in pairs. However, the systematic design method about it has not been proposed yet. In this paper, we studied a design analysis for determining geometrical parameters of the magnetic roller by using a commercial FEM tool of the 3D Maxwell. Through a series of simulation, we obtained the relationship of several geometrical parameters affecting the torque of the conveyor.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.151-154
• /
• 2008

The field emission lamps have the advantages to their cold cathode-characteristic and the eco-friendly, We realized that the dual emitter system showed very simple structure which gate and cathode electrodes are formed on the same glass surface. In this paper, we reported the properties of dual emitters depended on variation of gate width and spacing for optimum panel structure. In combination of dual emitter structure and bi-polar driving, electron beam spreads more than normal gate structure or diode structure, and emission uniformity increased in dual emitter structure at 5"-diagonal.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.548-553
• /
• 2008

Low Floor buses have no steps to get on or get off the main cabin to provide the old and the handicapped with easy access. The car body for the low floor bus was designed to consider Korean physical standard, passenger capacity (standee, seated, handicapped), arrangement of vehicle components, and bus law or regulations. It was designed as an one body, without any reinforcement armature, which has light-weight sandwich constructions with glass epoxy skins, aluminum honeycomb cores and inner-frames. In this paper, torsion rigidity of the designed car body was evaluated and compared with that of a car body with reinforcement armatures in the cabin. Finite element method verified that the designed car body without reinforcement armatures could satisfy requirements of torsion rigidity.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.4 no.3
• /
• pp.51-56
• /
• 2005

This research presents a modeling and a manufacturing method of screw flow meter. This paper introduces the efficient design and manufacturing method of screw type flow meter using reverse engineering and test technology. The methods introduced this paper utilize the reverse engineering that is increasing accuracy of modeling and manufacturing of reverse model. And then it can be used in performance test with hydraulic test equipment. Hence this can be used in the basic document for development of the quite accurate flowmeter.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.62-63
• /
• 2017

According to the rapid development of digital technology, the free formed buildings with complex and various curved surfaces are being constructed. Most of the external cladding of free formed buildings have been applied materials such as metal, glass, FRP, GFRC, etc. However, these materials have many disadvantages such as a complicated manufacturing process for realizing 3D irregular shape and an increase in production period and cost. Therefore, the studies for UHPC which is an optimized material for overcoming this problem for a long time in overseas. This study reviewed the remodeling construction of Samsung-dong KEB Hana Bank appling the exterior curved UHPC panel for the first time in Korea. As a result, we confirmed the possibility of UHPC panels with various free formed shapes.