• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.6 no.3
• /
• pp.171-178
• /
• 2008

Metal filter elements were newly introduced to the high temperature filter(HTF) system in the low- and intermediate-level radioactive waste vitrification plant. In order to evaluate the performance of various metal materials as filter media, elements made of AISI 316L, AISI 904L, and Inconel 600 were included to the test set of filter elements. At the visual inspection to the elements performed after completion of each test, a few dark spots were observed on the surface of some elements. Especially they were found much more at the AISI 316L elements than others. To check the dark spots are the corrosion phenomena or not, two kinds of analyses were performed to the tested filter elements. Firstly, the surfaces or the cross sections of filter specimens cut out from both normal area and dark spot area of elements were analyzed by SEM/EDS. The results showed that the dark spots were not evidences of corrosion but the deposition of sodium, sulfur and silica compounds volatilized from waste or molten glass. Secondly, the ring tensile strength were analyzed for the ring-shape filter specimens cut out from each kind of element. The result obtained from the strength tested showed no evidence of corrosion as well. Conclusionally, depending on the two kinds of analysis, no evidences of corrosion were found at the tested metal filter elements. But the dark spots formed on the surface could reduce the effective filtering area and increase the overall pressure drop of HTF system. Thus, continuous heating inside filter housing up to dew point will be required normally. And a few long-period test should be followed for the exact evaluation of corrosion of the metal filter elements.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.05a
• /
• pp.129-131
• /
• 1995

In order to investigated the effects of crystal stucture in electrical breakdown of plyethylene film, Low molecular materials in polyethylene are removed by the method as follow Polyethylene was dissolved in xylene and filtered through a glass fiber filter, And then, a polyethyene thin films of thickness 0.4~1.4$\mu\textrm{m}$ are prepared with heat treatment from solution casting. To evaluate the performance of PE film. Electrical breakdown of PE film as measured on M(Al)-I(PE)-M(Al) systemes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.11
• /
• pp.1604-1611
• /
• 2003

The experimental investigation of a coal splitter used in the 500㎿(e) boilers of fossil power plant is carried out to validate the design criteria. To predict air flow and the amount of particles at the exit, velocity and the weight of particles are measured on test planes using the coal splitter model with two-dimensional phase doppler particle analyzer and the glass fiber filter. It is found that the position of guide plate influences significantly both flow rates of gas and particle at the exit. Gas flow rate was a linear function of the guide plate, whereas particle flow rate was a exponential function of it.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.993-996
• /
• 2001

In the composition of 0.16BaO-0.15(Nd$\_$0.87/,Bi$\_$0.13/)$_2$O$_3$-0.69TiO$_2$$.$Glass [EG-2782] 3wt% addition sintered at 1080$^{\circ}C$, we could obtained microwave properties of dielectric constant $\varepsilon$$\_$r/= 80.1, quality factor Q ${\times}$ f = 810 (at 3.5 GHz]) and temperature coefficient of resonant frequency $\tau$$\_$f/ = -1.3 [ppm/$^{\circ}C$]

• Fibers and Polymers
• /
• v.5 no.1
• /
• pp.68-74
• /
• 2004

This work presents a series of experimental tests on new practical approaches in membrane design to improve extraction capacity and rate. We chose an extraction system involving Aliquat 336 as the extractant and Cd(II) as the metal ion to be extracted to demonstrate these new approaches. The core element in the new membrane assembly was the extractant loaded sintered glass filter. This membrane assembly provided a large interface area between the extractant and the aqueous solution containing metal ions. By recycling the aqueous solution through the membrane assembly, the extraction rate was significantly improved. The membrane assembly also offered good extraction capacity.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.17-19
• /
• 2008

An advanced TFT-LCD structure was proposed to increase aperture ratio (AR). In this structure, metal layers formed below the data lines are used as light-blocking layers, achieving higher AR ratio than that of a conventional structure. Since average misalignment between the metal light-blocking layers and pixel electrodes is smaller than that of black matrixes on color filter glass, substantially less light-blocking areas are needed to achieve misalignment margin. The AR of the LCD panel fabricated by using proposed structure was enhanced by 18.7 % over that of the conventionally structured panel.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.810-813
• /
• 2003

Application of inorganic silica-neodymia alloy films grown by sputtering technology to the dielectric layer of plasma display panel (PDP) is presented. The experimental results reveal that dielectric constant of the alloy films increases with neodymia concentration. Also, the alloy films act as band rejection color filter owing to sharp absorptions originating in the intratransition within the 4f shell of the $Nd^{3+}$ ion. In the optical band pass region, the transmittances of the alloy films show higher than those of commercial glass-like dielectrics. As a result, the luminance of PDP device with the alloy dielectric layer is higher than that of device with conventional dielectrics, indicating wider color gamut and higher color purity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.8
• /
• pp.995-999
• /
• 2014

In this paper, a new size-reduction approach for branch-line coupler is introduced which uses parallel end-shorted coupled lines with lumped capacitors. The characteristic of the new design was analyzed using even-odd mode method, and simulated on HFSS before fabricated on the FR4 epoxy glass cloth copper-clad plat (CCL) PCB substrate at center frequency of 1 GHz. The electrical length of transmission line was reduced to 15 degrees, therefore the size of branch-line coupler was largely reduced approximately maintaining the same characteristic around the stable center frequency. The insertion loss of the branch-line coupler filter was -4.39 dB. The size of the overall hybrid is $20mm{\times}20mm$. Measurements results were well agreed with the simulated ones.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.2
• /
• pp.13-21
• /
• 2002

A new method for measuring fiber length and fiber coarseness was developed using image analysis technique. Measured fibers were transferred to a glass slide on a filter paper placed on a wire of the laboratory paper machine. After staining the fibers on the slide, mean fiber lengths and coarseness were measured by a commercial image analysis software, named KS400. The resultant data obtained from the image analysis displayed a close correlation with those from FS-200 and also showed excellent reproducibility as well as those from FS-200. The length of synthetic fibers over 10 mm long could be readily measured by this new analysis technique. Finally, a substantial improvement in precision for measuring fiber length and coarseness was made with less operator's effort for a given time.

• Journal of Sensor Science and Technology
• /
• v.20 no.1
• /
• pp.46-52
• /
• 2011

In this paper, the swept source-optical coherence tomography system using frequency domain mode locked(FDML) laser has realized. The FDML swept source laser showed 55.03 kHz sweeping speed, 125 nm sweeping range, and 9 mW output optical power, which are the superiority of FDML laser compared to previous swept source lasers. Also, through the cross-sectional image captured at 5 frames per second for a mirror, a 1 mm-thickness glass plate, and a thumb bottom, the performance of the system has demonstrated.