Water and salt budgets in the Yellow Sea and Bohai are analyzed based on the historical data and CTD data collected recently using box models. The amounts of volume transport and of water exchange across the boundary between the Yellow and East China Seas are estimated to be 2,330-2,840 $\textrm{km}^3$/yr and 109-133 $\textrm{km}^3$/yr, respectively, from the one-layer box model. Corresponding water residence time is 5-6 years. In the Bohai, water residence time is twice as long as that in the Yellow Sea, suggesting that the Yellow Sea and Bohai cannot be considered as a single system in the view of water and salt budgets. The results indicate that water and salt budgets in the Yellow Sea depend almost only on the water exchange between the Yellow and East China Seas. The computation with the coupled two-layer model shows that water residence time is slightly decreased to 4-5 years for the Yellow Sea. In order to reduce uncertainties for the budgeting results the amount of the discharge from the Changjiang that enters into the Yellow Sea, the vertical advection and vertical mixing fluxes across the layer interface have to be quantified. The decreasing trend of the annual Yellow River outflow is likely to result that water residence time is much longer than the current state, especially for the Bohai. The completion of the Three Gorges dam on the Changjiang may be change the water and salt budgets in the Yellow Sea. It is expected that cutting back the discharge from the Changjiang by 10% through the dam would increase water residence time by about 10%.
The curvilinear hydrograph can be replaced by an equivalent triangular hydrograph which is more easily constructed and, for routing through reservoirs or stream channels, gives results about as accurate as those obtained using the curvilinear hydrograph. A synthetic hydrograph is prepared using the data from a number of watersheds to develop a dimensionless unit hydrograph applicable to ungauged watersheds. The dimensionless unit hydrograph for the NakDong River Basin was prepared from the unit hydrographs of a variety of nine subwatersheds. The equation for the peak rate of flow (unit volume of runoff in 1.0mm) was derived as {{{{ { q}_{p } = { 0.21AR} over { {T }_{p } } }}}} The results summarized in this study are as follows: 1) It found that the watershed lag time (Lg, hrs) could be expressed by Lg=0.253(L.Lca)0.4171 The product L.Lca is a measure of the size and shape of the watershed. Correlation coefficient for Lg was 0.97 which defined with high significance. 2) The base length of the unitgraph, in hours, was adopted as Tb=17.51+2.073Lg with high significant correlation coefficient, 0.92. 3) Time in hour from start of rise to peak rate (TP) generally occured at the position of 0.289 Tb with some indication of higher values for larger watershed. 4) Triangular hydrograph is a dimensionless unitgraph prepared from the 40 unitgraphs. The equation is shown as {{{{ { q}_{p } = { K.A.R} over { { T}_{p } } }}}}. The constant K=0.21 is defined to NakDong River basin. 5) In the light of the results analyzed in this study, average errors in the peak discharge of the Trjangular unitgraph was estimated as 5.34 percent to the peak of observed average unitgraph. Each ordinate of the Triangular unitgraph was approached closely to the observed one.
본 논문에서는 사회적으로나 개인적으로 매우 민감한 조사에서 조사하고자 하는 모집단이 여러 개의 층으로 구성되어 있고, 각 층이 양적인 속성으로 되어 있는 경우에 Himmelfarb-Edgell의 가법 모형과 Gjestvang-Singh의 가법 모형에 단순임의추출법 대신에 층화추출법을 적용한 층화 가법 양적속성 확률화응답모형을 제안하였다. 제안한 두 모형으로부터 각 층의 양적속성에 대한 모평균의 추정뿐만 아니라 모집단 전체 모평균에 대한 추정을 할 수 있는 이론적 체계를 마련하였다. 그리고 제안한 두 모형에서 비례배분과 최적배분 문제를 다루었으며, 각 배분법에 따른 분산식을 도출하였다. 마지막으로 두 층화 가법 양적속성 확률화응답모형들 간의 효율성을 비교해 본 결과 Gjestvang-Singh의 층화 가법 모형이 Himmelfarb-Edgell의 층화 가법 모형보다 효율적으로 나타났고, 특히 hh값이 작을수록 즉, 제시한 모형의 특성이 직접질문에 가까워질수록 Gjestvang-Singh의 층화 가법 모형의 효율성이 커짐을 알 수 있었다.
The bacteria on the surface of slaughtered meat was monitored to investigate the relationships between microbiological quality and sanitation management in slaughter process of cattle and pig. It was conducted to evaluate the microbiological quality on the surface of slaughtered beef and pork in Seoul from January to December 2004. Two hundred and thirty three beef and 233 pork carcasses were surveyed on generic E coli counts and standard plate count for microbiological quality and Salmonella spp, Listeria monocytogenes, Staphylococcus aureus, Clostridium perfringens and E coli O157: H7 as pathogenic microorganisms. The prevalence of the excellent or good grade $(10^4\;CFU/cm^2)$ in beef and pork carcasses were $100\%\; and\;99.2\%$, respectively. The frequency of beef carcasses with less than $10^2\;CFU/cm^2$ of generic I coli counts was $100\%$, while that of pork carcasses was $99.6\%$. Of 233 beef carcasses, $1(0.42\%)$ was contaminated with L monocytogenes and $6(2.58\%)$ with C perfringens. Of 233 pork carcasses, $11(4.72\%),\;2(0.86\%),\;and\;2(0.86\%)$ were contaminated with L monocytogenes, C perfringens, and S aureus, respectively, Salmonella spp and E coli O157:H7 were not detected with all of the beef and pork carcasses. In conclusion, this study emphasized the Importance of relationship between microbiological quality and sanitation management in slaughter process of cattle and pig, in abattoirs.
Two sets of data on carcass traits and beef cut parameters were used to investigate the relationships between carcass and beef cut measurements, which can be used to make predictions of retail cut percentages. One set had a total of 1,141 measurements of Hanwoo cattle of three different sex origins, which were slaughtered in an abattoir located at the National Institute of Animal Science, RDA, Korea from 1996 to 2008. To develop prediction models for retail cut percentage with higher accuracies than the current model, another set consisting of a total of 13,389 records of carcass and beef cut traits were collected from 30 abattoirs and butcheries in Korea from 2008 to 2009. Bulls yielded heavier and leaner carcasses than steers. High correlation coefficients were estimated between amount of body fat and percent retail cut (-0.82) as well as between back fat thickness (BF) and percent retail cut (-0.62). The amount of retail cut, however, was highly correlated with body weight before slaughter (BW, 0.95) or with cold carcass weight (CWT, 0.94). Relationships between percent retail cut and measurable beef yield traits, BF, loin eye area (LEA) or CWT varied by sex class, which must be considered for development of a prediction model with high accuracy. Models of data for all breeds and sexes fit the effects of breed, sex, and interaction of abattoir by butchers, whereas models of data for each breed and sex fit the effect of interaction of abattoir by butcher only. Due to possible future changes in back fat control, we performed a log transformation of BF. Our new models fit better than the currently used model.
As the dimension of Cu interconnects has continued to reduce, its resistivity is expected to increase at the nanoscale due to increased surface and grain boundary scattering of electrons. To suppress increase of the resistivity in nanoscale interconnects, alloying Cu with other metal elements such as Al, Mn, and Ag is being considered to increase the mean free path of the drifting electrons. The formation of Al alloy with a slight amount of Cu broadly studied in the past. The study of Cu alloy including a very small Al fraction, by contrast, recently began. The formation of Cu-Al alloy is limited in wet chemical bath and was mainly conducted for fundamental studies by sputtering or evaporation system. However, these deposition methods have a limitation in production environment due to poor step coverage in nanoscale Cu metallization. In this work, gap-filling of Cu-Al alloy was conducted by cyclic MOCVD (metal organic chemical vapor deposition), followed by thermal annealing for alloying, which prevented an unwanted chemical reaction between Cu and Al precursors. To achieve filling the Cu-Al alloy into sub-100nm trench without overhang and void formation, furthermore, hydrogen plasma pretreatment of the trench pattern with Ru barrier layer was conducted in order to suppress of Cu nucleation and growth near the entrance area of the nano-scale trench by minimizing adsorption of metal precursors. As a result, superconformal gap-fill of Cu-Al alloy could be achieved successfully in the high aspect ration nanoscale trenches. Examined morphology, microstructure, chemical composition, and electrical properties of superfilled Cu-Al alloy will be discussed in detail.
본 연구에서는 완전 내재적 기법을 이용한 2계 자유도 모델에 대한 플러터 해석을 수행하였다. 유동해석을 위하여 2차원 Navier-Stokes 지배방정식을 ε-SST 난류모델과 DP-SGS 병렬화 기법을 이용해 구성하였다. 구조해석을 위하여 피치 와 플런지의 2계 자유도를 갖는 모델을 구성하였으며 시간영역에서의 해석을 위하여 유동해석과 마찬가지로 이중 시간 전진 기법을 이용하였다. 가상 시간 전진에서 유체-구조 결합을 통해서 강성결합을 구현하였으며 이를 천음속 플러터 예측에 적용하였다. 플러터 해석의 전형적인 응답인 감쇠응답, 중립응답, 발산응답 및 limit cycle oscillation (LCO) 등을 계산하였으며, 더불어 플러터 속도 경계곡선을 작성하였다. 천음속 플러터 해석은 난류모델 뿐만 아니라 유체-구조 결합 방법에 따라 다른 특성을 보임을 확인하였다.
The Korean native pig (KNP) have been considered as animal models for animal biotechnology research because of their relatively small body size and their presumably highly inbred status due to the closed breeding program. However, little is reported about the use of KNP for animal biotechnology researches. This study was performed to establish the somatic cell nuclear transfer (SCNT) protocol for the production of swine leukocyte antigens (SLA) homotype-defined SCNT KNP. The ear fibroblast cells originated from KNP were cultured and used as donor cell. After thawing, the donor cells were cultured for 1 hour with 15 ${\mu}M$ roscovitine prior to the nuclear transfer. The numbers of reconstructed and parthenogenetic embryos transferred were $98{\pm}35.2$ and $145{\pm}11.2$, respectively. The pregnancy and delivery rate were 3/5 (60%) and 2/5 (40%). One healthy SLA homotype-defined SCNT KNP was successfully generated. The recipient-based individual cloning efficiency ranged from 0.65 to 1.08%. Taken together, it can be postulated that the methodological establishment of the production of SLA homotype-defined cloned KNP can be applied to the generation of transgenic cloned KNP as model animals for human disease and xenotransplantation researches.
흡연으로 발생되는 담배연기는 주류 연기와 비주류 연기로 구분된다. 담배연기 중 실내로 확산되는 연기의 대부분은 비주류 연기이며, 비주류 연기의 유해물질 농도는 주류 연기의 농도보다 2~3배 높다. 본 연구에서는 $TiO_2$ 광촉매의 doping 성분에 따른 비주류 담배연기 내의 CO, $H_2S$, $NH_3$, HCHO의 제거 효율을 확인하고자 하였다. 실험 결과, CO가 최대 78.37% 제거되었으며, $TiO_2$ 광촉매 공정이 CO 제거에 효과적인 것으로 확인되었다. 또한 CO, $H_2S$, HCHO의 제거에 있어서 $TiO_2$ 광촉매에 doping된 O, Si 성분에 의해 영향을 크게 받는다. 결론적으로, doping된 O, Si 성분이 많을수록 유해물질 제거효율이 높다.
Vinegar is a very popular ingredient used in many cuisines. It is also known for its beneficial health, beauty and possible weight-loss properties. The authors report on a patient who presented to the emergency department with unstable vital signs complaining of generalized abdominal pain after ingestion of 450 ml of apple cider vinegar. We documented a case of corrosive gastrointestinal injury with persistent metabolic acidosis occurring after ingesting apple cider vinegar with an acetic acid concentration of 12~14%. Toxic damage to the liver and kidney were also observed, peaking on post-ingestion day 3. The patient received supportive care and hemoperfusion for three days without much clinical improvement and died in the seventh day of intensive care due to disseminated intravascular coagulation and multi organ failure. Edible vinegar, when taken in large amounts, is capable of inducing corrosive injuries of the GI tract as well as severe systemic toxicities, such as metabolic acidosis. Safety precautions regarding vinegar deserve more public attention and clinicians also should be astute enough to recognize the potential damage accompanying vinegar ingestion.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.