• Geomechanics and Engineering
• /
• v.25 no.3
• /
• pp.207-219
• /
• 2021

Several additives are used to enhance the geotechnical properties (e.g., shear wave velocity, shear modulus) of soils to provide sustainable, economical and eco-friendly solutions in geotechnical and geo-environmental engineering. In this study, piezoelectric ring actuators are used to measure the shear wave velocity of unreinforced, fiber, cemented, and fiber reinforced cemented Toyoura sand. One dimensional oedometer tests are performed on medium dense specimens of Toyoura sand-cement-fiber-silica flour mixtures with different percentages of silica flour (0-42%), fiber and cement (e.g., 0-3%) additives. The experimental results indicate that behavior of the mixtures is significantly affected by the concentration of silica flour, fiber and cement additives. Results show that with the addition of 1-3% of PVA fibers, the shear wave velocity increases by only 1-3%. However, the addition of 1-4% of cement increases the shear wave velocity by 8-35%. 10.5-21% increase of silica flour reduces the shear wave velocity by 2-5% but adding 28-42% silica flour significantly reduces the shear wave velocity by 12-31%. In addition, the combined effect of cement and fibers was also found and with only 2% cement and 1% fiber, the shear wave velocity increase was found to be approximately 24% and with only 3% cement and 3% fibers this increased to 35%. The results from this study for the normalized shear modulus and normalized mean effective stress agree well with previous findings on pure Toyoura sand, Toyoura silty sand, fiber reinforced, fiber reinforced cemented Toyoura sand. Any variations are likely due to the difference in stress history (i.e., isotropic versus anisotropic consolidation) and the measurement method. In addition, these small discrepancies could be attributed to several other factors. The potential factors include the difference in specimen sizes, test devices, methods of analysis for the measurement of arrival time, the use of an appropriate Ko to convert the vertical stresses into mean effective stress, and sample preparation techniques. Lastly, it was investigated that there is a robust inverse relationship between α factor and 𝞫₀ exponent. It was found that less compressible soils exhibit higher 𝜶 factors and lower 𝞫₀ exponents.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.40 no.4
• /
• pp.251-260
• /
• 2022

Although the number of trees affected by pine wilt disease is decreasing, the affected area is expanding across the country. Recently, with the development of deep learning technology, it is being rapidly applied to the detection study of pine wilt nematodes and dead trees. The purpose of this study is to efficiently acquire deep learning training data and acquire accurate true values to further improve the detection ability of U-Net models through learning. To achieve this purpose, by using a filtering method applying a step-by-step deep learning algorithm the ambiguous analysis basis of the deep learning model is minimized, enabling efficient analysis and judgment. As a result of the analysis the U-Net model using the true values analyzed by period in the detection and performance improvement of dead pine trees of wilt nematode using the U-Net algorithm had a recall rate of -0.5%p than the U-Net model using the previously provided true values, precision was 7.6%p and F-1 score was 4.1%p. In the future, it is judged that there is a possibility to increase the precision of wilt detection by applying various filtering techniques, and it is judged that the drone surveillance method using drone orthographic images and artificial intelligence can be used in the pine wilt nematode disaster prevention project.

• Journal of the Korean Society of Costume
• /
• v.26
• /
• pp.175-206
• /
• 1995

The costume culture of China is as old and varied as her long history. As China is a multiracial nation and consists of fifty-six min-ority races including Han race, there are not only fifty-six different costumes in China but each races' costume habit is very different. Therefore, Chinese penninsula can be considered an enor-mous exhibition center of the costumes. This study undertook on the assumption that the costumes' mainstream of Korea and east-northern Asia as well as that of China could be examined by investigating the minority races' costumes in the east-and west-northern areas of China. The process of evolution of the costume of a particular people, country or area is subject not only to constraints related to geography such as climate, topography or local products but is also affected by numorous environmental influences including cultural, economic, social and even pol-itical ones in terms of the selection of material, styling, color and standard of tailoring. In other words, things like philosophy of life, religious be-lief, aesthetic outlook, moral code, class system, degree of affluence, and cultural exchange will all be reflected directly or indirectly by features of a people's or country's style costume. Of course, there are several factors affecting to the style of costume of the minority people in China. However, the only three factors-geo-graphical and environmental, production method, and religious belef-will be touched in this study. First of all, the geograghical and eenviron-mental factor would be the decisive one because the costume should be designed to overcome the constraints of climate and geographical environ-ments. Accordingly, each race has an unique style of costume. The costume of the minority races in the northern parts are loose and wide, and made of warm furs. For instance, Mongolian robe has the quality of anti-wind, anti-cold and warmness, and the width of a sleeve is narrow and long. Secondly, the costume style can be said to be limited by the production pattern, when the geo-graphical environment was affected to decide the costume style, the production pattern was together affected to it . In case of Mongolian robe, they should satisfy the dual condition as the practical function. One is the condition that they should be fitted to the climate, and the other is the condition that they should be suit-able to the nomadic life. Mongolian robes are suitable to the nomadic peoples because they are designed for not only overcoming the cold wind and weather but being used as the bedquit at night. The costumes of Hoche people was made of the skin of the fish and wild animals because of their main means of living being fishing and hunting. Accordingly, their costumes are dur-able, warm and water-proof. Finally, the style of the costume is affected by the religious belief. In other words, the pattern in fashion is closely related with the religious be-lief or ancestor worship and nature worship. Ac-cordingly, the symbols of these worship are often emerged in the decoration of the costume. The design of costume of the people in the northern areas of China is very simple. It is related with their monotheism. On the other hand, the costumes of twen쇼 minority races in the east-northern parts of China can be devided into three racial groups such as the long robes of Man people and Mongols, Tunics of the peoples in the west-northern areas, and the pants and jackets of Hoche people. The minorority races all has not only the unique costume habit but their costumes are also related with their living style and production means.

• Geophysics and Geophysical Exploration
• /
• v.11 no.1
• /
• pp.52-59
• /
• 2008

We have developed a new deep-towed marine DC resistivity survey system. It was designed to detect the top boundary of the methane hydrate zone, which is not imaged well by seismic reflection surveys. Our system, with a transmitter and a 160-m-long tail with eight source electrodes and a receiver dipole, is towed from a research vessel near the seafloor. Numerical calculations show that our marine DC resistivity survey system can effectively image the top surface of the methane hydrate layer. A survey was carried out off Joetsu, in the Japan Sea, where outcrops of methane hydrate are observed. We successfully obtained DC resistivity data along a profile ${\sim}3.5\;km$ long, and detected relatively high apparent resistivity values. Particularly in areas with methane hydrate exposure, anomalously high apparent resistivity was observed, and we interpret these high apparent resistivities to be due to the methane hydrate zone below the seafloor. Marine DC resistivity surveys will be a new tool to image sub-seafloor structures within methane hydrate zones.

• Journal of Soil and Groundwater Environment
• /
• v.14 no.4
• /
• pp.33-44
• /
• 2009

Water curtain of an underground LPG storage cavern is a facility to prevent leakage of high pressure gases, for which groundwater should flow freely towards the cavern and groundwater level also must be stably maintained. In this study, in order to evaluate qualities of seepage water and surrounding groundwater of an underground LPG storage cavern in Yeosu, 4 rounds of samplings, field measurements and laboratory analyses (February, May, August, October of 2007) were conducted. According to field measurements, pH was weak acidic to neutral but it gradually increased with time. Electrical conductivity (EC) of groundwater near a salt stack showed very high values between 10.47 and 38.50 mS/cm. Dissolved oxygen (DO) showed a very wide range of 0.20~8.74 mg/L and a mean of oxidation-reduction potential (ORP) was 159 mV, which indicated an oxidized condition. Levels of $Fe^{2+}$ and $Mn^{2+}$ were mostly less than 3 mg/L. All of seepage waters showed a Na-Cl type while only groundwater near the salt stack showed a Na-Cl type with a high total dissolved solid. The other groundwaters exhibited typical $Ca-HCO_3$ types. Levels of aerobic bacteria were mostly very high (573-39,520 CFU/mL). Based on the analyses of these hydrochemistry and biological characteristics, it is concluded that there are no particular problems in groundwater and seepage water, which not causing a trouble in the cavern operation. However, both for control of bio-clogging and for sustainable operation of the water curtain system, a regular hydrochemical and microbiological monitoring is required for the seepage water and surrounding groundwater.

• Journal of the Korean earth science society
• /
• v.42 no.3
• /
• pp.264-277
• /
• 2021

This study analyzed the relationship between the total precipitable water vapor in the atmosphere and the moving speed of recent typhoons. This study used ground observation data of air temperature, precipitation, and wind speed from the Korea Meteorological Administration (KMA) as well as total rainfall data and Red-Green-Blue (RGB) composite images from the U.S. Meteorological and Satellite Research Institute and the KMA's Cheollian Satellite 2A (GEO-KOMPSAT-2A). Using the typhoon location and moving speed data provided by the KMA, we compared the moving speeds of typhoon Bavi, Maysak, and Haishen from 2020, typhoon Tapah from 2019, and typhoon Kong-rey from 2018 with the average typhoon speed by latitude. Tapah and Kong-rey moved at average speed with changing latitude, while Bavi and Maysak showed a significant decrease in moving speed between approximately 25°N and 30°N. This is because a water vapor band in the atmosphere in front of these two typhoons induced frontogenesis and prevented their movement. In other words, when the water vapor band generated by the low-level jet causes frontogenesis in front of the moving typhoon, the high pressure area located between the site of frontogenesis and the typhoon develops further, inducing as a blocking effect. Together with the tropical night phenomenon, this slows the typhoon. Bavi and Maysak were accompanied by copious atmospheric water vapor; consequently, a water vapor band along the low-level jet induced frontogenesis. Then, the downdraft of the high pressure between the frontogenesis and the typhoon caused the tropical night phenomenon. Finally, strong winds and heavy rains occurred in succession once the typhoon landed.

• International Journal of Aeronautical and Space Sciences
• /
• v.10 no.1
• /
• pp.75-82
• /
• 2009

In this parer, we propose a new way of improving DGNSS service using combination of multiple SBAS information. Because SBAS uses Geostationary Earth Orbit (GEO) satellites, it has very large coverage but it can be unavailable in urban canyon because of visibility problem. R. Chen solved this problem by creating Virtual Reference Stations (VRS) using the SBAS signal [1]. VRS converts SBAS signal to RTCM signals corresponding its location, and broadcast the converted RTCM signals over the wireless internet. This method can solve the visibility problem cost effectively. Furthermore it can solve DGNSS coverage problem by creating just a transmitter instead of a reference station. Developing above method, this paper proposes the methods that integrate two or more SEAS signals into one RTCM signal and broadcast it. In Korea, MSAS signal is available even though it is not officially certified for Korean users. As a Korean own SBAS-like system, there is the internet-based KWTB (Korean WADGPS Test Bed) which we developed and released at ION GNSS 2006. As a result, virtually two different SBAS corrections are available in Korea. In this paper, we propose the integration methods for these two independent SBAS corrections and present the test results using the actual measurements from the two systems. We present the detailed algorithm for these two methods and analyze the features and performances of them. To verify the proposed methods, we conduct the experiment using the logged SBAS corrections from the two systems and the RINEX data logged at Dokdo monitoring station in Korea. The preliminary test results showed the improved performance compared to the results from two independent systems, which shows the potential of our proposed methods. In the future, the newly developed SBASs will be available and the places which can access the multiple SBAS signals will increase. At that time, the integration or combination methods of two or more SBASs will become more important. Our proposed methods can be one of the useful solutions for that. As an additional research, we need to extend this research to the system level integration such as the concept of the decentralized W ADGPS.

• Journal of the Korean earth science society
• /
• v.34 no.1
• /
• pp.13-27
• /
• 2013

Quantitative precipitation estimation (QPE) is one of the most important elements in meteorological and hydrological applications. In this study, we adjusted the QPE from an S-band weather radar based on co-kriging method using the geostatistical structure function of error distribution of radar rainrate. In order to estimate the accurate quantitative precipitation, the error of radar rainrate which is a primary variable of co-kriging was determined by the difference of rain rates from rain gauge and radar. Also, the gauge rainfield, a secondary variable of co-kriging is derived from the ordinary kriging based on raingauge network. The error distribution of radar rain rate was produced by co-kriging with the derived theoretical variogram determined by experimental variogram. The error of radar rain rate was then applied to the radar estimated precipitation field. Locally heavy rainfall case during 6-7 July 2009 is chosen to verify this study. Correlation between adjusted one-hour radar rainfall accumulation and rain gauge rainfall accumulation improved from 0.55 to 0.84 when compared to prior adjustment of radar error with the adjustment of root mean square error from 7.45 to 3.93 mm.

• Journal of Korean Society for Geospatial Information Science
• /
• v.10 no.4 s.22
• /
• pp.41-50
• /
• 2002

RPM is the one of the sensor models which is proposed by Open GIS Consortium (OGC) as image transfer standard. And it is the sensor model for end-users using IKONOS, a commercial pushbroom satellite, imagery which provide about 1m ground resolution. Parameters called RPC which is IKONOS RFM coefficients are serviced to end-users. But if some users try to make additional effort to get rigorous geo-spatial information, it is necessary to apply mathematic or abstract sensor models, because vendors don't offer any ancillary data for physical sensor models such as satellite orbit and navigation. Abstract sensor models such as pushbroom Direct Linear Transform (DLT) require many GCPs well distributed in imagery, and mathematic sensor model such as RFM, polynomials need much more GCPs. Therefore RPC modification using additional a few GCPs is the best solution. In this paper, two methods are proposed to modify RPC. One is method to use pseudo GCPs generated in normalized cubic, and another method uses parameters observations and a few GCPs. Through two methods, we get improvement of accuracy 50% and over.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.10
• /
• pp.4251-4256
• /
• 2015

Background: Exposure to cigarette may affect human health and increase risk of a wide range of diseases including pulmonary diseases, such as chronic obstructive pulmonary disease (COPD), asthma, lung fibrosis and lung cancer. However, the molecular mechanisms of pathogenesis induced by cigarettes still remain obscure even with extensive studies. With systemic view, we attempted to identify the specific gene modules that might relate to injury caused by cigarette smoke and identify hub genes for potential therapeutic targets or biomarkers from specific gene modules. Materials and Methods: The dataset GSE18344 was downloaded from the Gene Expression Omnibus (GEO) and divided into mouse cigarette smoke exposure and control groups. Subsequently, weighted gene co-expression network analysis (WGCNA) was used to construct a gene co-expression network for each group and detected specific gene modules of cigarette smoke exposure by comparison. Results: A total of ten specific gene modules were identified only in the cigarette smoke exposure group but not in the control group. Seven hub genes were identified as well, including Fip1l1, Anp32a, Acsl4, Evl, Sdc1, Arap3 and Cd52. Conclusions: Specific gene modules may provide better understanding of molecular mechanisms, and hub genes are potential candidates of therapeutic targets that may possible improve development of novel treatment approaches.