• Korean Journal of Hydrosciences
• /
• 제3권
• /
• pp.81-96
• /
• 1992

This study represents the methodology for feasibility analysis of small hydro power SHP plant. Cumulative density function of Weibull distribution and Thiessen method were adopted to decide flow duration curve at SHP candidate site. The perfomance prediction model and construction cost estimation model for tunnel-type SHP plant were developed. Eight tunnel -type SHP candidate sites existing on Han-river were selected and surveyed for actual site reconnaissance. The performance characteristics and economical feasibility for these sites were analyzed by using developed models. As a result, it was found that the optimum design flowrate with the lowest unit generation cost for tunel-type SHP candidate site were the flowrate concerming with between 20% and 30% of time ratio on the flow duration curve. Additionally, primary design specifications such as design flowrate, effective head, capacity, annual averageload factor, annual electricity production were estimated and discussed for eight surveyed SHP candidate sites.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1987년도 한국자동제어학술회의논문집(한일합동학술편); 한국과학기술대학, 충남; 16-17 Oct. 1987
• /
• pp.741-746
• /
• 1987

Solar cell which transforms the light energy into the electric energy from Sun comes into prominence as a new energy for next generation. However, it is difficult to obtain the stable output voltage and current from the solar cell due to the uncertainty in weather conditions, etc, In the present paper, two types of control laws are considered for regulating the input voltage in a photovoltaic energy storage system such as the system with the super conducting magnetic energy storage. (1) Oone is the design of optimal controller. (2) The other is that of weighted minimum prediction error controllers (weighted one-step ahead controllers). Simulation study for the above controllers is performed to see how they work and to get preliminary knowledge in the regulation of the input voltage to the experimental photovoltaic energy storage system.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 하계종합학술대회논문집
• /
• pp.126-129
• /
• 1998

In order to control the flow of traffics in ATM networks and optimize the usage of network resources, an efficient control mechanism is necessary to cope with congestion and prevent the degradation of network performance caused by congestion. This paper proposes a new UPC(Usage Parameter Control) mechanism that varies the token generation rate and the buffer threshold of leaky bucket by using a Neural Network controller observing input buffers and token pools, thus achieving the improvement of performance. Simulation results show that the proposed adaptive algorithm uses of network resources efficiently and satisfies QoS for the various kinds of traffics.

• 한국유체기계학회 논문집
• /
• 제5권1호
• /
• pp.13-19
• /
• 2002

In the present study, a numerical simulation is performed for the flow through a cooling fan. The computation was performed by using commercial code, STAR-CD. A rotating fan was simulated by rotational motions using MRF (Multiple Rotating Reference Frame) in a steady-state analysis and sliding interface (rotating meshes) in an unsteady-state analysis. The results of numerical computation were in good agreement with experimental data. In order to calculate the acoustic signal, the unsteady flow-field was firstly calculated. The acoustics of the fan is calculated by using acoustic analogy based on the unsteady flow-field. The predicted acoustic signal shows the characteristics of the uneven bladed-fan.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.335-338
• /
• 2006

A Numerical study of the cavitation within a centrifugal pump is carried out using CFD commercial code, FLUENT. The objective of this study is to predict the onset of cavitation within the pump blade and the degradation in the pressure rise due to the generation and transport of vapor. A pump designed for the study is a six bladed, one-circular arc impeller design suggested by A.J. Stepanoff et al. The Steady-state calculations are performed for a wide range of flow rate without the cavitation to investigate the pump performance. The design head and efficiency show a very good agreement with the numerical results at the design flow rate. After the validation with the numerical results, the pump performance and the onset of cavitation within the blade is predicted by changing NPSH at the design flow rate.

• 제어로봇시스템학회논문지
• /
• 제18권6호
• /
• pp.608-611
• /
• 2012

This paper focuses on attitude stabilization performance improvement of the quadrotor flying robot. First, the dynamic model of quadrotor flying robot was estimated through PEM (Prediction Error Method) using experimental input/output data. And attitude stabilization performance was improved by increasing the generation frequency of PWM signal from 50 Hz to 500 Hz. Also, the controller is implemented using a standard PID (Proportional-Integral-Derivative) controller augmented with feedback on angular acceleration, allowed the gains to be significantly increased, yielding higher bandwidth. Improved attitude stabilization performance is verified by experiment.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -2
• /
• pp.1098-1100
• /
• 2002

Inter-RNC(radio network controller) and inter-BSC(base station center) hard handovers involve rerouting. Thus additional delay time for the new bearer setup and reroute determination should be considered. For theses kinds of handovers we propose a new scheme and coined it as ICHP(Inter-Cluster Handover Prediction). When a call approaches a boundary cell of a cluster, ICHP prepares for the handover by performing resource reservations and reroute computation in advance. Performance analysis shows that ICHP provides faster handover and that it lowers the blocking probability.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2060-2065
• /
• 2003

Aeolian tone generation from a two dimensional circular cylinder is numerically investigated via direct numerical simulation and hydrodynamic-acoustic splitting method. All governing equation are spatially discretized with the sixth-order compact scheme and fourth-order Runge-Kutta method to avoid excessive numerical dissipations and dispersions of acoustic quantities. Comparisons of two results show that the previous splitting method can not accurately predict the aeroacoustic noise of wall bounded shear flow. In this study, a perturbation viscous term and a new energy equation have been developed. This modified splitting method accurately predicts aeroacoustic noise from wall-bounded shear flow. The present results agree very well with the direct numerical simulation solution.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1148-1153
• /
• 2003

An adequate method for the prediction of machining errors is essential to improve productivity and product quality. But it is known that there is a remarkable difference between values calculated by conventional roughness model and measured values of actual machined surfaces under high efficient cutting condition. This paper introduces the theoretical analysis of characteristic lines of cut remainder to evaluate a geometrical surface roughness accurately. In this study, analytic equations of the characteristic lines are derived from the surface generation mechanism of ball end milling considering the actual trochoidal trajectories of cutting edges. The predicted results are compared with the results of conventional roughness model.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.629-634
• /
• 1996

Heat generation in machine operating condition makes thermal deformation and thermalstress in the structure, which results in the change the contact characteristics of machine joint such s change of shrinkage fit, contact heat conductance and contact pressure. As the change of contact pressure is related to variation of static, dynamic and thermalcharacteristics, the prediction of transient contact perssure is strongly required. This paper presents some analytical results which will be effective to predict static and dynamic characteristics of the compound cylindrical structure.