• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.325-332
• /
• 2003

In general, soil characteristics are estimated through the sample gathered by field boring without considering sample disturbance. However, soil characteristics must be changed by the degree of sample disturbance. Therefore it be need to estimate the soil characteristic considering sample disturbance which can be occurred by the change of stress condition, sampling technique and handling method. On this study, we analyzed the sample disturbance by using the methods of volume change, residual effective stress, elastic modulus and the curve of consolidation tests. In order to estimate the relationship between sample disturbance and soil characteristics, we used the piston sample and the block sample. As the results, it should be considered in design that the disturbance of the block sample, which affects the strength and compression properties of clay, is smaller than the disturbance of piston sample.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.265-268
• /
• 2003

In the extrusion process, the working material is forced to flow through a die with the desired profile. In general, the width of an extruded section is limited to about an inch less than the diameter of the round billet. But through the lip die, material is spreaded to produce a wider extruded section than the diameter of round billet. In this study, the extrusion process of an aluminum plate using the lip die is investigated. The width of the extruded plate is 450mm that is formed from the round billet with a diameter of 250mm. The flow characteristic through the lip die is considered to produce the wide-extruded plate with a small billet using rigid plastic FE analysis. Based on the result of FE analysis, new designs of lip die are proposed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.203-205
• /
• 2006

This paper presents a study on the winding method and structure of core of single phase induction motor in order to design the high efficiency motor. In case of single phase induction motor, winding fill factor and the number of turns in each slot are not uniform in general. Moreover, these can be the critical parameters for high efficiency design in case the size of motor should be restricted within certain volume. Therefore, we should analyze the effects of these parameters related to efficiency parameter. The characteristic analysis was performed by using FEM.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.190-192
• /
• 2003

Single phase induction motor is used widely in various electronic appliances by advantage that is simple structure and a low-cost. As high starting torque characteristic is mostly used capacitor run single phase induction motor. In this paper, it is applied that speed controller of Capacitor run single phase induction motor of digital way used general microprocessor, and phase control method used average voltage. Torque get non-linearity to domain of low speed. Unstable domain of low speed is applied of integral cycle control. so it is wide that Speed control domain. Also, PID controller is used to improve characteristic of fast response. The validity of proposed method is verified from simulation and experiment result

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권4호
• /
• pp.520-526
• /
• 2006

Wave Energy is a derivative of the solar energy input to the earth, which is accumulated on open water surfaces by the action of the winds Waves are disturbances in the water surface. This paper is interested primarily in progressive waves, which carry energy from one place to another Waves are irregular in size and frequency. Moreover the surface of the sea is one of the most hostile environments for engineering structures and materials. The idea of harnessing the tremendous power of the ocean's waves is not new. Hundreds of wave energy conversion techniques have been suggested over the last two centuries. Although many WECS (Wave Energy Conversion Systems) have been invented, only a few systems have been tested and evaluated. This paper describes the characteristic of WES (Wave Energy System) in terms of, devices, resource and potential, etc.. Finally, this paper provides a summary of general and specific conclusions and recommendations concerning WECS potential in Korea.

• Journal of Mechanical Science and Technology
• /
• 제14권9호
• /
• pp.928-934
• /
• 2000

This paper describes a method developed for the simulation of ring pack lubrication characteristic in an internal combustion engine. In general, the quantity of oil supply for piston ring lubrication may be insufficient in filling the entire volume formed at the interference between the piston ring and the cylinder liner. Thus the oil starvation condition should be considered in analyzing piston ring lubrication. In order to reasonably estimate the amount of oil left over on the cylinder liner, the flow rate at the posterior portion of the interface should be calculated with an adequate boundary condition that confirms flow continuity condition. In this analysis, oil starvation and open-end boundary conditions are considered at the inlet and outlet of the piston rings. The lubrication characteristic of each piston ring is obtained by an iterative method with sequential steps. It is revealed that piston rings are operated under oil starvation in most operating cycles and the result under these conditions are quite different from that with the fully-flooded assumption.

• 대한수학교육학회지:학교수학
• /
• 제6권4호
• /
• pp.361-372
• /
• 2004

수학영재학생들로 하여금 자신들의 잠재적 재능을 최대한 발현하도륵 교육하려면, 무엇보다 먼저 그들이 어떤 특성을 지니고 있는지 구체적이고 면밀하게 분석할 필요가 있다. 특히 우리나라 실정에 맞는 수학영재교육의 행정적, 제도적 시행을 위해서는 수학영재학생들의 특성에 대한 장기간에 걸친 실증적 연구가 뒷받침되어야 한다. 본 연구에서는 서울 소재 5대학교 과학영재교육원 수학분과에 소속된 학생들을 중심으로 실제 증명 사례, 수학적 성향 특성 검사, 사회적응 설문, 그리고 Torrance 창의성 검사(그림) 등을 통하여 수학영재학생들의 인지적, 정의적, 창의적 특성을 과학영재 및 일반학생들과 비교, 분석하고자 한다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.42-45
• /
• 2002

General wheel mark in mono-crystalline silicon wafer finding is able to be expected because it depends on radius ratio and angular velocity ratio of wafer and wheel. The pattern is predominantly determined by the contour of abrasive grits resulting from a relative motion. Although such a wheel mark is made uniform pattern if the process parameters are fixed, sub-surface defect is expected to be distributed non-uniformly because of characteristic of mono-crystalline silicon wafer that has diamond cubic crystal. Consequently it is considered that this phenomenon affects the following process. This paper focused on kinematic analysis of wafer grinding process and simulation program was developed to verify the effect of process variables on wheel mark. And finally, we were able to predict sub-surface defect distribution that considered characteristic of mono-crystalline silicon wafer

• 대한정형도수물리치료학회지
• /
• 제1권1호
• /
• pp.49-63
• /
• 1995

Examination at the spine is dependent on assessment of function. At all spine levels a number of general anatomical considerations hold sway which together dictate the format of the evaluation. Because disc lesions are common and generally responsive to treatment, the examination sets out to differentiate between disc lesions and the other sources of pain as well as establishing the particular treatment that will benefit any given displacement. As elsewhere in the body, displacements give rise to certain characteristic symtoms and signs. First, the history is indicative. Second, any loose fragment in the joint restricts spinal movement in some but not all directions, producing the non-capsular pattern characteristic of internal derangement. Third, a displacement protruding posteriorly interferes with the dura mater ; apart from pain, this adversely affects the dura's normal painless mobility. Fourth, a displacement protruding laterally connects with the appropriate nerve root emerging from the dura mater. Finally, compression of the spinal cord strongly contraindicates manipulation, the primary treatment for cartilaginous displacements.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.560-563
• /
• 2004

Invar is a compound metal of Fe-Ni system and contain 36％ Ni. The most distinction characteristic of Invar is the coefficient of thermal expansion is 1.0 10$^{-6}$ /$^{\circ}C$. That is a tenth of general steel material. This low thermal expansion characteristic of Invar is applied to the missile, aircraft, monitor CRT and frontier display's shadow mask such as FED and OLED. The usage of the Invar shadow mask for display is increasing due to the requirement of larger size and flatness monitor. The Invar shadow mask is machined by two ways electro-forming and laser now. However the electro-forming takes a too long time and the laser machining is accompanied with Burr. In this study, PEMM(pulse electrochemical micro machining) is conducted to machine the micro hole to the Invar and 80${\mu}{\textrm}{m}$ hole was machined.