• Geosystem Engineering
• /
• 제21권6호
• /
• pp.318-325
• /
• 2018

Eight tight sandstone reservoir samples from $He_8$ and $Shan_1$ Formations of the Sulige Gas field were selected to perform gas-water micro-displacement experiment based on authentic sandstone micro-model. The gas pressure-relief experiment was proposed for the first time to simulate the pressure change and gas-water percolation characteristics in the process of gas exploitation. The experiment results show that: (1) In the process of gas accumulation, the gas preferentially flows into the well-connected pores and throats with large radius, but rarely flows into the area without pores and throats. (2) Under sufficient gas drive, the water in pores and throats usually exists in the forms of 'thin water film', 'thick water film', and 'water column', but under insufficient gas drive, gas fails to flow into new pathways in time, so that the reservoirs with large pores and throats are high in water cut. (3) Under the same water saturation, the reservoirs with better petrophysical properties has higher gas recovery factor within unit time. Under the same petrophysical conditions, the reservoirs with lower water saturation show higher gas recovery factor within unit time. The higher the permeability, the stronger the liquid carrying capacity of reservoirs.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.461-464
• /
• 1995

We have investigated the effects of sputtering Ar gas pressure on magnetic anisotropy of Co/Pt multilayers, where sputtering Ar gas pressure was varied from 2 to 20 mTorr. The surface and volume anisotropies were found to be strongly dependent on sputtering Ar gas pressure. In particular, the surface anisotropy exhibited more than fourfold enhancement as Ar pressure was decreased from 20 to 5 mTorr. We have found that the surface anisotropy was closely correlated with the low-angle x-ray diffraction intensity. We believe that these results are mainly ascribed to the variation of microstructure in the Co/Pt multilayer thin films with sputtering Ar gas pressure.

• 한국가스학회지
• /
• 제7권3호
• /
• pp.51-57
• /
• 2003

본 논문에서는 압력용기의 밀봉성과 밀접한 관계를 맺고 있는 O-링 그루브 형상의 온도분포와 변형거동 특성에 대한 연구를 수행하고자 한다. 압력용기에 작용하는 온도는 히터에 의해 가열되고, 압력은 가스 압축기에 의해 가압된다. 결국, 압력용기는 제한된 작업기간동 안 높은 압력과 높은 온도를 유지해야 한다 이러한 작동조건에서 압력용기의 가스는 구형 그루브에 설치된 두 개의 O-링에 의해 대기중으로 누출되지 말아야 한다. 유한요소해석 결과에 의하면, 압력용기의 밀봉성을 확보하기 위해서는 메탈 시일 소재의 열적, 기계적 특성이 대단히 우수해야 한다는 사실을 지적하고 있다 즉, 메탈 시일 소재는 높은 열전도 계수와 낮은 기계적 강도를 유지해야 밀봉성을 유지하는데 유리하다. 이러한 소재는 O-링을 설치하는 구형 그루브의 밀봉간극이나 그루브의 폭을 줄여줄 수 있기 때문에 압력용기의 밀봉특성을 향상시키게 된다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권5호
• /
• pp.103-113
• /
• 1996

The properties of the deposited film depend on the deposition condition and these, in turn depend critically on the morphology and crystal orientation of the films. Therefore, it is important to clarify the nucleation occurrence and growth stage of the morphology and orientation of the film affected by deposition parameters, e.g. the gas pressure and bias voltage etc. In this work, magnesium thin flims were prepared on cold-rolled steel substrates by a thermo-eletron activation ion plating technique. The influence of nitrogen gas pressure and substrate bias voltage on their crystal orientation and morphology of the coated films were investigated by scanning electron microscopy (SEM) and X-ray diffraction, respectively. The diffraction peaks of magnesium film became less sharp and broadened with the increase of nitrogen gas pressure. With an increase in nitrogen gas pressure, flim morphology changed from colum nar to granular structure, and surface crystal grain-size decreased. The morphology of films depended not only on gas pressure but also on bias voltage, i.e., the effect of increasing bias voltage was similar to that of decreasing gas pressure. The effect of crystal orientation and morphology of magnesium films on corrosion behaviors was estimated by measuring anodic polarization curves in deaerated 3%NaCl solution. Magnesium, in general, has not a good corrosion resistance in all environments. However, these magnesium films prepared by changing nitrogen gas pressure showed good corrosion resistance. Among the films, magnesium films which exhibited granular structure had the highest corrosion resistance. The above phenomena can be explained by applying the effects of adsorption, occlusion and ion sputter of nitrogen gas.

• 한국가스학회지
• /
• 제24권6호
• /
• pp.61-69
• /
• 2020

본 논문은 압력과 온도조건에 따라 수소저장용기 TYPE 1에서 발생하는 거동특성을 FEM(Finite Element Method)으로 연구한 것이다. 용기의 구조안전성 평가를 위해 최고압력에서 발생한 VMS(Von Mises stress)을 소재의 YS(Yield Strength)를 비교하였고, 수명예측을 위한 기초데이터로써 PSED(Plastic Strain Energy Density) 결과를 분석하였다. 해석결과에 의하면 최고압력 40 Mpa 이상의 가스압에서 저장용기의 바닥면에 항복강도보다 높은 VMS가 발생하여 수소가스 저장용기의 안전성은 확보되지 않았다고 판단된다. 또한, 온도조건에 의해 발생한 VMS의 결과는 대단히 낮아서 온도에 의한 거동은 영향을 무시할 수 있다. VMS/YS이 1이하가 되는 최고압력은 약 30Mpa으로 계산되어 본 논문의 대상이 되는 수소저장용기는 30 Mpa이하의 가스충전압력으로 관리되어야 함을 알 수 있다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제45회 KOSCO SYMPOSIUM 초록집
• /
• pp.93-96
• /
• 2012

The spontaneous ignition mechanism of high pressure hydrogen gas released into tube is well-deduced from previous studies. However, those results have a limit because the studies have been conducted at low burst pressure of about 10 MPa. In this study, the process or ignition feature are investigated with higher burst pressure of up to 30 MPa through numerical analysis. The results show that the trend of ignition became to be different with a burst pressure. While two reaction regions is important to initiate the ignition when burst pressure is about 10 MPa, the reaction of the core region does not play a role in ignition inside the tube when a burst pressure is above 20 MPa.

• Korean Chemical Engineering Research
• /
• 제58권4호
• /
• pp.610-617
• /
• 2020

In process installations, chemicals operate at high temperature and high pressure. Propylene is used as a basic raw material for manufacturing synthetic materials in the petrochemical industry; However, it is a flammable substance and explosive in the gaseous state. Thus, caution is needed when handling propylene. To prevent explosions, an inert gas, carbon dioxide, was used and the changes in the extent of explosion due to changes in pressure and oxygen concentration at 25 ℃, 100 ℃, and 200 ℃ were measured. At constant temperature, the increase in explosive pressure and the rates of the explosive pressure were observed to rise as the pressure was augmented. Moreover, as the oxygen concentration decreased, the maximum explosive pressure decreased. At 25 ℃ and oxygen concentration of 21%, as the pressure increased from 1.0 barg to 2.5 bar, the gas deflagration index (K_g) increased significantly from 4.71 barg·m/s to 18.83 barg·m/s.

• 한국가스학회지
• /
• 제9권1호
• /
• pp.26-32
• /
• 2005

본 논문에서는 고압용기의 밀봉을 위해 사용하는 메탈시일의 설계 안전성에 대한 연구결과를 제시하고 있다. 기본적으로 고압용기의 1차적 밀봉은 메탈시일에 의해 이루어지고, 2차적 밀봉은 탄성체 고무로 제작된 0-링에 의해 가스누출이 차단된다. 유한요소해석 결과에 의하면, 가스누출 차단을 위해 사용한 알루미늄 소재의 밀봉장치는 강재를 사용한 경우보다 우수한 밀봉성을 보여주고 있다. 이것은 알루미늄 소재의 열팽창 특성이 상대적으로 우수하기 때문이다. 메탈시일과 압력용기 구조물에 걸리는 변형과 응력분포는 외부에서 공급된 가스압보다는 용기 내부에서 전달된 온도차에 의해 크게 지배를 받는 것으로 알려져 있다. 따라서 메탈시일의 소재는 통상적으로 $200^{\circ}C$이하로 유지되는 것이 소재의 강도와 밀봉성 측면에서 안전하다.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.216-221
• /
• 2005

The heat transfer coefficient and pressure drop during gas cooling process of carbon dioxide in a helically coiled tube were investigated experimentally. The experiments were conducted without oil in the refrigerant loop. The main components of the refrigerant loop are a receiver, a variable speed pump, a mass flowmeter, a pre-heater, a gas cooler(test section) and an isothermal tank. The test section is a double pipe type heat exchanger with refrigerant flowing in the inner tube and water flowing in the annulus. It was made of a copper tube with the inner diameter of 4.85 [mm], the outer diameter of 6.35 [mm] and length of 10000 [mm]. The refrigerant mass fluxes were 200${\sim}$600 [kg/$m^2$s] and the average pressure varied from 7.5 [MPa] to 10.0 [MPa]. The main results were summarized as follows: The heat transfer coefficient of supercritical $CO_2$ increases, as the cooling pressure of gas cooler decreases. And the heat transfer coefficient increases with the increase of the refrigerant mass flux. The pressure drop decreases in increase of the gas cooler pressure and increases with increase the refrigerant mass flux.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.1-9
• /
• 2001

The soot yield has been studied by a premixed propane-oxygen-inert gas combustion in a specially designed disk-type constant-volume combustion chamber to investigate the effects of pressure, temperature and turbulence on soot formation. Premixtures are simultaneously ignited by eight spark plugs located on the circumference of chamber at 45 degree intervals in order to observe the soot formation under high pressures. The eight flames converged compress the end gases to a high pressure. The laser schlieren and direct flame photographs for observation field with 10 mm in diameter are taken to examine into the behaviors of flame front and gas flow in laminar and turbulent combustion. The soot volume fraction in the chamber center during the final stage of combustion at the highest pressure is measured by the in situ laser extinction technique and simultaneously the corresponding burnt gas temperature by the two-color pyrometry method. The pressure and temperature during soot formation are changed by varying the initial charge pressure and the volume fraction of inert gas compositions, respectively. It is found that the soot yield increases with dropping temperature and rising pressure at constant equivalence ratio, and that the soot yield of turbulent combustion decreases in comparison with that of laminar combustion because the burnt gas temperature increases with the drop of heat loss.