• Proceedings of the IEEK Conference
• /
• 대한전자공학회 2004년도 학술대회지
• /
• pp.776-779
• /
• 2004

A RF front-end module is designed for GIS(Gas Insulated Substation) which is employed for effective and efficient very high voltage transmission. Major advantage of the unit is improved PO detection sensitivity through minimizing the effect of surrounding interference signals, which is achieved by controlling the gain and the selection of the frequency band, for the precise detection of any UHF PO (Partial Discharge) disturbance occurred in the GIS due to some unwanted problems. For the development of the module, various switches for providing selected signal paths, wideband LNA, 3 BPF for selecting detection frequency band, and video detector are designed, fabricated and measured on 1 mm FR4 substrate with various RF components. The detection sensitivity of the unit was <-60 dBm that is sufficient to detect UHF PO signals as low as 1 pC. It is believed that the value is enough to detect the signal occurred in GIS.

• Journal of the Korean Society of Safety
• /
• 제14권4호
• /
• pp.78-84
• /
• 1999

A compact air-preheating type heat exchanger was developed and tested for the ultra-high temperature heat recovery applications. For the direct use of exhaust gases up to $1200^{\circ}C$, the heat exchanger adopted a ceramic core with high strength and low thermal expansion coefficient less than $1{\times}10^{-6}^{\circ}C^{-1}$. The ceramic core was fabricated by special extrusion and bonding techniques. To minimize thermal stresses in the core, spring-loaded sealing mechanism was designed and successfully installed. 1-pass air flow scheme was adopted for the compactness and cost-savings. The pressure test for the ceramic core showed no failure under 35 kPa and less than 3% leak under 7 kPa. Flue gas simulation system was developed to investigate the performance of the heat exchanger. The test results showed normal operations of the heat exchanger up to $1200^{\circ}C$ of exhaust gases and relatively high heat recovery efficiencies of 31～39% depending upon exhaust gas temperatures..

• Journal of computational fluids engineering
• /
• 제6권4호
• /
• pp.15-25
• /
• 2001

Numerical prediction of the diffusion controlled transition in a turbine gas pass is important because it can change the local heat transfer rate over a turbine blade as much as three times. In this study, the gas flow over turbine blade is simplified to the flat plate boundary layer, and an adaptive grid scheme redistributing grid points within the computation domain is proposed with a great emphasis on the construction of the grid control function. The function is sensitized to the second invariant of the mean strain tensor, its spatial gradient, and the interaction of pressure gradient and flow deformation. The transition process is assumed to be described with a κ-ε turbulence model. An elliptic solver is employed to integrate governing equations. Numerical results show that the proposed adaptive grid scheme is very effective in obtaining grid independent numerical solution with a very low grid number. It is expected that present scheme is helpful in predicting actual flow within a turbine to improve computation efficiency.

• Journal of the Korean Chemical Society
• /
• 제4권1호
• /
• pp.67-69
• /
• 1957

The synthetic method of tetramethyl-4,4'-diaminobenzophenone accomplished by W. Michler is to pass gaseous carbonyl chloride in dimethylaniline until theoretical value of weight increases at room temperature and synthesize the ketone by heating it at above 120$^{\circ}C. In the result of the experiment to synthesize the ketone by Michler's method, it was observed that if gaseous phosgen was to be used at room temperature according to the method, the gas inhaling tube would be closed up by reaction products (gruel-like crystals) before the theoretical amount of gases passed in and causing difficulty for gas to be produce or inhaled With a view to remove the difficulty, the author examined an article published by W. Michler entitled. "The synthesis of organic acid with phosgen" and guessing that the use of liquid phosgen could overcome the difficulty, succeeded in synthesizing the substance in good yield easily by reacting dimethylaniline with phosgen that was condensed into liquid state.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.379-381
• /
• 1997

The dielectric layers in AC plasma display panel(AC PDP) are essential to the discharge cell structure, because they protect metal electrodes from sputtering by positive ion and from a sheath of wall charges which are essential to memory function of AC PDP. Furthermore, this layer should be transparent because the visible light must pass through the layer. In this paper, the dielectric breakdown strength and transparency of the dielectric layer on the discharge electrodes are studied. The variables in this test are the dielectric layer thickness, dielectric firing condition, gas pressure, species of gas and so on.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제2C권6호
• /
• pp.297-303
• /
• 2002

We have developed an on-line ultrasonic detector to monitor partial discharge in an operating transformer. The ultrasonic sensor has 150[KHz] resonance frequency and contains a pre-amplifier with 60[㏈] gain. The on-line ultrasonic detector has 50~300[KHz] frequency band-pass filter to remove electrical and mechanical noises from the transformer. This detector has an ultrasonic signal discrimination algorithm which discriminates ultrasonic signals due to partial discharge in a transformer. A moving average method of ultrasonic signal number was employed to effectively monitor the increasing trend of the partial discharge. This paper describes an experience of partial discharge detection in a 154[㎸] operating transformer using an ultrasonic detector. With regards to gas analysis in oil, C2H2 gas was produced with a warning level in this transformer We detected ultrasonic signals on the transformer steel wall, and estimated the position of partial discharge. With further inspection, we found carbonized marks due to partial discharge on the supporting bolt which fastens the windings.

• Journal of Sensor Science and Technology
• /
• 제22권2호
• /
• pp.100-104
• /
• 2013

A superhydrophobic mesh is a unique structure that blocks water, while allowing gases, sound waves, and energy to pass through the holes in the mesh. This mesh is used in various devices, such as gas- and energy-permeable waterproof membranes for underwater sensors and electronic devices. However, it is difficult to fabricate micro- and nano-structures on three-dimensional surfaces, such as the cylindrical surface of a wire mesh. In this research, we successfully produced a superhydrophobic water-repellent mesh with a high contact angle (> $150^{\circ}$) for nanofibrous structures. Conducting polymer (CP) composite nanofibers were evenly coated on a stainless steel mesh surface, to create a superhydrophobic mesh with a pore size of $100{\mu}m$. The nanofiber structure could be controlled by the deposition time. As the deposition time increased, a high-density, hierarchical nanofiber structure was deposited on the mesh. The mesh surface was then coated with Teflon, to reduce the surface energy. The fabricated mesh had a static water contact angle of $163^{\circ}$, and a water-pressure resistance of 1.92 kPa.

• Journal of Magnetics
• /
• 제11권3호
• /
• pp.103-107
• /
• 2006

In grain oriented electrical steel process, hot band annealing has thought to be essential for obtaining good magnetic properties. New hot rolling method of heavy reduction in early hot rolling stage was applied to obtain good magnetic properties in GO process without hot band annealing. Hot rolling was carried out by varyinghot rolling reduction distribution along hot rolling pass. The heavy hot rolling reduction in rear stand improves the magnetic flux density in the case of no hot band annealing. The hot band specimens of the heavy reduction in front stand shows the elongated hot deformed microstructures in the center layer and strong {001}<110> texture.On the contrary, the heavily reduced specimens in rear stand shows the recrystallization in the center layer of hot band and strong {111}<112> and {110}<001> textures.

• Proceedings of the Safety Management and Science Conference
• /
• 대한안전경영과학회 2012년 춘계학술대회
• /
• pp.221-232
• /
• 2012

Cycle analysis has been performed to find out the optimum design point of the BOG re-liquefaction plant. The cycle state, defined by three cycle variables, was mainly described by the three cold temperatures of the three-pass heat exchanger, on which the constraints by the heat exchanger are imposed. The cycle states which are confined within a domain limited by the temperature constraints were the primary issue of this study. The BOG mass within the domain was analyzed first and then the cycle performance was related to the BOG mass afterwards, which enabled us to explain the observed behavior of the cycle performance under the temperature constraints by the heat exchanger. A good cycle performance could be ensured if the two cold Nitrogen temperatures of the three temperatures were placed close together near $-140^{\circ}C$ while the BOG temperature is kept far above enough, but not too far, from $-140^{\circ}C$ such that it does not interfere in their optimum temperature range.

• Journal of Welding and Joining
• /
• 제35권3호
• /
• pp.75-81
• /
• 2017

Recently in the welding field, the establishment of unmanned and automated systems are rapidly developing. Accurate interpretation of the welding phenomenon is applied a number of monitoring systems. In this paper, butt welding (6t) type I using Plasma-MIG welding was carried out. And we evaluated characteristics of the Al-5083 aluminium alloy in Plasma-MIG hybrid welding. Process variables including the plasma current, MIG voltage, wire feeding rate and the welding speed were used. Butt welding was conducted 1 pass. Argon gas was used as the protective gas that results from the experiment were able to achieve full penetration. In addition to monitoring the welding process occurring during MIG welding current, welding votage and Plasma current, voltage were collected in real time, the photodiode and CCD cameras observing the phenomenon that the welding is in progress were measured using a quantity of light.