• The Korean Journal of Ecology
• /
• v.20 no.4
• /
• pp.239-244
• /
• 1997

Hybrid poplar (Populus trichocarpa $\times$ P. deltoides) clones were fumigated with ozone. Fumigation was applied for 6 to 8 hours each day for approximately 3 months at ozone concentrations of 0.090 to 0.115 ppm using by open-top chambers. Growth and biomass of hybrid poplar seedlings were reduced by ozone exposure. Mean percentage of falling leaves in ozone-treated plant was 6 times higher than that of charcoal-filtered plant. Among physiological responses, rate of photosynthesis, stomatal conductance, transpiration and initial Rubisco activity were significantly lower in seedlings grown in ozone environment compared seedlings grown in charcoal-filtered air. All these physiological results supported that biochemical process to be a key feature to understand reduction in photosynthesis.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.656-657
• /
• 2008

The droplet dynamics in a hydrophilic/hydrophobic microchannel, which is applicable to a typical proton exchange membrane fuel cell (PEMFC), is studied numerically by solving the equations governing conservation of mass and momentum. The liquid-gas interface or droplet shape is determined by a level set method which is modified to treat contact angles. The matching conditions at the interface are accurately imposed by incorporating the ghost fluid approach based on a sharp-interface representation. The effects of contact angle, inlet flow velocity, droplet size and side wall on the droplet motion are investigated parametrically. Based on the numerical results, the droplet dynamics including the sliding and detachment of droplets is found to depend significantly on the contact angle. Also, a droplet removal process is demonstrated on the combination of hydrophilic and hydrophobic surfaces.

• Corrosion Science and Technology
• /
• v.15 no.2
• /
• pp.92-107
• /
• 2016

Graphene was coated on austenitic and martensitic stainless steels to simulate the metallic bipolar plate of proton exchange membrane fuel cell (PEMFC). Graphene oxide (GO) was synthesized and was reduced to reduced graphene oxide (rGO) via a hydrazine process. rGO was confirmed by FE-SEM, Raman spectroscopy and XPS. Interfacial contact resistance (ICR) between the bipolar plate and the gas diffusion layer (GDL) was measured to confirm the electrical conductivity. Both ICR and corrosion current density decreased on graphene coated stainless steels. Corrosion resistance was also improved with immersion time in cathodic environments and satisfied the criteria of the Department of Energy (DOE), USA. The total concentrations of metal ions dissolved from graphene coated stainless steels were reduced. Furthermore hydrophobicity was improved by increasing the contact angle.

• Proceedings of the KWS Conference
• /
• 1996.10a
• /
• pp.148-152
• /
• 1996

A transient two-dimensional (2D) model was developed for investigating the heat and fluid flow in old pools and determining velocity profile and temperature distribution for the Gas Metal Arc (GMA) welding process. The mathematical formulation deals with the driving farces (electromagnetic, buoyancy, surface tension and plasma drag forces) as well as energy exchange between the molten filler metal droplet and weld pools. A general thermofluid-mechanics computer program, PHOENICS, was employed to numerically solve the governing equation with the associated source terms. The results of computation have shown that the electromagnetic and surface tension farces as will as the molten filler metal droplet have major influence in shaping the weld pool geometry.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2122-2125
• /
• 2008

Because the reheating furnace consumes a large amount of energy to heat up the slabs, it is very important to find an optimal temperature patterns in the furnace for energy saving as well as uniform target temperature at the exit of the furnace. In this study, the temperature profiles in the slab are determined by solving the transient one-dimensional heat conduction equation in conjunction with boundary conditions with total heat exchange factors. The optimal temperature patterns are obtained to minimize the fuel consumption with satisfying the predetermined constraint conditions. The design optimization is performed by using a genetic algorithm and the optimal results are validated with results obtained from the PIDO tool, called as P.I.A.n.O.

• Journal of Hydrogen and New Energy
• /
• v.31 no.2
• /
• pp.259-264
• /
• 2020

In this study, comparison study has been performed between two-stage compression and a vapor-recompression refrigeration cycle and a liquefaction using LNG cold heat. When using a first method using two-stage compression and a refrigeration cycle, at least three compressors are required, however when using LNG cold heat, no compressor is required since carbon dioxide can be pumped after condensing with the heat exchange with -160℃ of LNG. Through this study, we can save more than one hundred million KRW annually by using LNG cold heat instead of using gas compression and refrigeration cycle.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.3
• /
• pp.751-767
• /
• 1994

Recent developments of S.I. engine, aiming to higher power, better fuel economy, lower air pollution and better driveability, have much focused on the importance of the role of computer simulation in engine research and development. In this point of view, improving engine performance requires finding some means to improve volumetric efficiency. Up to now there have been several attempts to optimize the intake and exhaust system of internal system of S.I. engine by computer simulation. There appear to be few studies available, however, of such simulation & experimental studies applied to the optimization of exhaust manifold configuration. In this study, gas exchange & power process of 4 cylinder S.I. Engine was studies numerically & experimentally, and governing equation of a one-dimensional unsteady compressible flow and combustion process were respectively solved by a characteristics method and 2-zone model. The aim of this study is to predict and investigate the influence of pressure wave interaction at the exhaust systems on engine performance with widely differing exhaust manifold configuration.

• Journal of Korean Elementary Science Education
• /
• v.19 no.2
• /
• pp.57-74
• /
• 2000

Students' concepts of scientific phenomena have become a point of focus in science education research. This study investigated into developmental process and mechanism of the students' respiration concept through a cross-age study. This study utilized the 1st, 3rd, 6th grade elementary students to find out changes in student's understanding of the concept of respiration. The 1st and 3rd grade level students were interviewed what the respiration mean and whether each of living things respires, etc. The 6th grade students were interviewed and tested. Respiration is a word that students come across often in everyday life. It was found that they were more likely to associate respiration with its more common concept of breathing or gas exchange as opposed to its more scientific definition as the process in which nutrients are oxidized to provide energy. This trend didn't improve as they advanced grade. This is an indication that the knowledge system of student is split into a generic knowledge system and scientific knowledge system. Understanding of concept increased and differentiated across grade levels but that understanding was limited. They overcome their tendency to base their understanding of respiration on their understanding of human phenomena and learn to integrate their understanding of biological phenomena through a one organ - one role type of logic. They also intuitively explain everything based on their own experience.

• Korean Chemical Engineering Research
• /
• v.57 no.4
• /
• pp.469-474
• /
• 2019

Fermentation of palm oil mill effluent (POME) produces biohydrogen in a mixture at a specific set condition. This research was conducted to purify the produced mixed biohydrogen via absorption and membrane techniques. Three different solvents, methyl ethanolamine (MEA), ammonia ($NH_3$) and potassium hydroxide (KOH) solutions, were used in absorption technique. The highest $H_2$ purity was found using 1M MEA solution with 5.0 ml/s feed mixed gas flow rate at 60 minutes absorption time. Meanwhile, the purified biohydrogen using a polysulfone membrane had the highest $H_2$ purity at 2~3 bar operating pressure. Upon testing with proton exchange membrane fuel cell (PEMFC), the highest current and power produced at 100% $H_2$ were 1.66 A and 8.1 W, while the lowest were produced at 50/50 vol% $H_2/CO_2$ (0.32 A and 0.49 W). These results proved that both purification techniques have significant potential for $H_2$ purification efficiency.

• Korean Chemical Engineering Research
• /
• v.53 no.6
• /
• pp.818-823
• /
• 2015

In this study, FT reaction in a microchannel was simulated using computational fluid dynamics(CFD), and sensitivity analyses conducted to see effects of channel geometry variables, namely, process channel width, height, gap between process channel and cooling channel, and gap between process channels on the channel temperature profile. Microchannel reactor considered in the study is composed of five reaction channels with height and width ranging from 0.5 mm to 5.0 mm. Cooling surfaces is assumed to be in isothermal condition to account for the heat exchange between the surface and process channels. A gas mixture of $H_2$ and CO($H_2/CO$ molar ratio = 2) is used as a reactant and operating conditions are the following: GHSV(gas hourly space velocity) = $10000h^{-1}$, pressure = 20 bar, and temperature = 483 K. From the simulation study, it was confirmed that heat removal in an FT microchannel reactor is affected channel geometry variables. Of the channel geometry variables considered, channel height and width have significant effect on the channel temperature profile. However, gap between cooling surface and process channel, and gap between process channels have little effect. Maximum temperature in the reaction channel was found to be proportional to channel height, and not affected by the width over a particular channel width size. Therefore, microchannels with smaller channel height(about less than 2 mm) and bigger channel width (about more than 4 mm), can be attractive design for better heat removal and higher production.