• 한국항공우주학회지
• /
• 제42권8호
• /
• pp.640-647
• /
• 2014

추진기관 배기 플룸의 적외선 복사(Infrared radiation :IR) 신호는 항공기 생존성에 영향을 미치는 주요 요인이다. 항공기의 생존성 향상을 위해 IR 감소 설계 기술이 적용된 추진기관의 정확한 IR 신호 예측이 필요하다. 본 연구는 유동 및 열전달 해석 코드를 이용하여 노즐 내부, 외부 자유류, 플룸 영역의 열유동장을 수치 해석하였다. 비회색가스의 특성을 효율적으로 해석하는 좁은밴드 기반의 재조합 회색가스가중합법을 적용하여 항공기 플룸에서 방사되는 파장별 IR 신호를 계산하였다. 개발된 프로그램의 정확성과 신뢰성을 확보하고자 1차원 모델에 대한 검증을 거친 후 항공기 추진기관의 열유동장 및 파장별 IR 신호 해석을 수행하였다. 해석을 통하여 상대적으로 플룸 내부에서 IR 복사강도가 높은 것을 확인하였고 온도, 분압, 화학종에 따라 다른 파장별 IR 신호 특성을 파악하였다. 노즐 출구 부근에서는 노즐 벽면의 고체 방사로 인하여 파장별 IR 복사강도가 연속적으로 나타났다.

• Asian Pacific Journal of Cancer Prevention
• /
• 제14권12호
• /
• pp.7121-7126
• /
• 2013

Aim: To examine lymph nodes obtained after lipolysis and liposuction of subcutaneous fat of the inguinal region of female vulvar cancer patients to explore the feasibility of clinical application. Methods: The field of operation was on the basis of the range of the conventional resection of inguinal lymph nodes. We injected lipolysis liquid fanwise, started liposuction after 15-20 minutes; then the subcutaneous fatty tissue was sucked out clearly by suction tube. We selected the first puncture holes located on 2-3 cm part below anterior superior spine, the others respectively being located 3cm and 6cm below the first for puncturing into the skin, imbedding a trocar to intorduce $CO_2$ gas and the specular body, and excise the lymph nodes by ultrasonic scalpel. The surgical field chamber was set with negative pressure drainage and was pressured with a soft saline bag after surgery. Results: A lacuna emerged from subcutaneous of the inguinal region after lipolysis and liposuction, with a wide fascia easily exposed at the bottom where lymph nodes could be readily excised. The number of lymph nodes of ten patients excised within the inguinal region on each side was 4-18. The excised average number of lymph nodes was 11 when we had mature technology. Conclusion: Most of adipose tissue was removed after lipolysis and liposuction of subcutaneous tissue of inguinal region, so that the included lymph nodes were exposed and easy to excise by endoscope. This surgery avoided the large incision of regular surgery of inguinal region, the results indicating that this approach is feasible and safe for used as an alternative technology.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.363-363
• /
• 2008

The development of dry etching process for sapphire wafer with plasma has been key issues for the opto-electric devices. The challenges are increasing control and obtaining low plasma induced-damage because an unwanted scattering of radiation is caused by the spatial disorder of pattern and variation of surface roughness. The plasma-induced damages during plasma etching process can be classified as impurity contamination of residual etch products or bonding disruption in lattice due to charged particle bombardment. Therefor, fine pattern technology with low damaged etching process and high etch rate are urgently needed. Until now, there are a lot of reports on the etching of sapphire wafer with using $Cl_2$/Ar, $BCl_3$/Ar, HBr/Ar and so on [1]. However, the etch behavior of sapphire wafer have investigated with variation of only one parameter while other parameters are fixed. In this study, we investigated the effect of pressure and other parameters on the etch rate and the selectivity. We selected $BCl_3$ as an etch ant because $BCl_3$ plasmas are widely used in etching process of oxide materials. In plasma, the $BCl_3$ molecule can be dissociated into B radical, $B^+$ ion, Cl radical and $Cl^+$ ion. However, the $BCl_3$ molecule can be dissociated into B radical or $B^+$ ion easier than Cl radical or $Cl^+$ ion. First, we evaluated the etch behaviors of sapphire wafer in $BCl_3$/additive gases (Ar, $N_2,Cl_2$) gases. The behavior of etch rate of sapphire substrate was monitored as a function of additive gas ratio to $BCl_3$ based plasma, total flow rate, r.f. power, d.c. bias under different pressures of 5 mTorr, 10 mTorr, 20 mTorr and 30 mTorr. The etch rates of sapphire wafer, $SiO_2$ and PR were measured with using alpha step surface profiler. In order to understand the changes of radicals, volume density of Cl, B radical and BCl molecule were investigated with optical emission spectroscopy (OES). The chemical states of $Al_2O_3$ thin films were studied with energy dispersive X-ray (EDX) and depth profile anlysis of auger electron spectroscopy (AES). The enhancement of sapphire substrate can be explained by the reactive ion etching mechanism with the competition of the formation of volatile $AlCl_3$, $Al_2Cl_6$ or $BOCl_3$ and the sputter effect by energetic ions.

• 천문학회보
• /
• 제37권1호
• /
• pp.42-42
• /
• 2012

The First stars (Pop.III stars) in the universe are expected to be formed between the recombination era at z - 1100 and the most distant quasar (z - 8). They have never been directly detected due to its faintness so far, but can be observed as a background radiation at around 1${\mu}m$ which is called the Cosmic Near-Infrared Background (CNB). Main part of the CNB is thought to be redshifted Lyman-alpha from gas clouds surrounding the Pop.III stars. Until now, the COBE (COsmic Background Explorer) and the IRTS (Infrared Telescope in Space) observed excess emission over the background due to galaxies. To confirm the COBE and the IRTS results and pursue more observational evidences, we carried out the sounding rocket experiment named the Cosmic Infrared Background ExpeRiment (CIBER). The CIBER is successfully launched on July 10, 2010 at White Sands Missile Range, New Mexico, USA. It consists of three kinds of instruments. We report the results obtained by LRS (Low Resolution Spectrometer) which is developed to fill the uncovered spectrum around 1${\mu}m$. LRS is a refractive telescope of 5.5 cm aperture with spectral resolution of 20 - 30 and wavelength coverage of 0.7 to 2.0${\mu}m$. After subtracting foreground components (zodiacal light, integrated star light and diffuse galactic light) from the sky brightness of observed five fields, there remained significant residual emission (even for the lower limit case) consistent with the IRTS and the COBE results. In addition, there exists a clear gap at 0.7 - 0.8${\mu}m$ in the CNB spectrum over the background due to galaxies according to recent results (Matsuoka et al. 2011; Mattila et al. 2011). The origin of the excess emission could be ascribed to the Pop.III stars with its active era of z = 7 - 10.

• 한국의학물리학회:학술대회논문집
• /
• 한국의학물리학회 2002년도 Proceedings
• /
• pp.161-163
• /
• 2002

The BNCT(Boron Neutron Capture Therapy) facility has been developed in Hanaro(High-flux Advanced Neutron Application Reactor), a research reactor of Korea Atomic Energy Research Institute. A typical tangenial beam port is utilized with this BNCT facility. Thermal neutrons can be penetrated within the limits of the possible maximum instead of being filtered fast neutrons and gamma rays as much as possible using the silicon and bismuth single crystals. In addition to, the liquid nitrogen (LN$_2$) is used to cool down the silicon and bismuth single crystals for the increase of the penetrated thermal neutron flux. Neutron beams for BNCT are shielded using the water shutter. The water shutter was designed and manufactured not to interfere with any other subsystem of Hanaro when the BNCT facility is operated. Also, it is replaced with conventional beam port plug in order to cut off helium gas leakage in the beam port. A circular collimator, composed of $\^$6/Li$_2$CO$_3$ and polyethylene compounds, is installed at the irradiation position. The measured neutron flux with 24 MW reactor power using the Au-198 activation analysis method is 8.3${\times}$10$\^$8/ n/cm$^2$ s at the collimator, exit point of neutron beams. Flatness of neutron beams is proven to ${\pm}$ 6.8% at 97 mm collimator. According to the result of acceptance tests of the water shutter, the filling time of water is about 190 seconds and drainage time of it is about 270 seconds. The radiation leakages in the irradiation room are analyzed to near the background level for neutron and 12 mSv/hr in the maximum for gamma by using BF$_3$ proportional counter and GM counter respectively. Therefore, it is verified that the neutron beams from BNCT facility in Hanaro will be enough to utilize for the purpose of clinical and pre-clinical experiment.

• 한국화재소방학회논문지
• /
• 제30권6호
• /
• pp.48-56
• /
• 2016

지난 2014.4.4.(금)14:50, 울산소재 대형 옥외저장탱크에 원유 충전 중 누출사고가 발생하여 사고현장에 긴급구조통제단이 가동됐다. 사고업체, 소방기관 및 유관기관이 지휘소에 모여 대응과 수습방안을 논의한 뒤 전원차단 및 시설작동금지, 가스농도 측정, 유증기 발생 억제, 누출 원유를 타탱크와 공정과정으로 이송, 해양오염 방지조치 등의 협업체계를 구축하여 수습하였다. 이 수습과정에서 유증기 발생방지와 점화원 차단을 가장 중시하여 조치함으로써 사고업체와 소방기관이 가장 우려했던 폭발과 화재사고는 발생하지 않았다. 이에 본 연구는 일반적인 재난의 긴급구조통제단과는 달리 운영해야 할 옥외탱크의 유류 누출, 폭발 및 화재 시의 긴급구조통제단 운영체계개선을 제시하고, 옥외탱크 유류 누출로 인한 폭발과 화재사고로 전이했을 경우를 가정한 방유제 바닥 종류에 따른 화염 확산속도와 연소시간을 실험 비교하였다. 또한, 소방차 포 노즐의 방사각도와 펌프압력에 따른 방사거리와 포의 도포면적을 실험 분석하여, 이후 옥외저장탱크의 유류 누출로 인한 폭발과 화재 시를 대비한 효과적인 현장대응과 수습방안을 제시하는 데 중점을 두었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.122-122
• /
• 1999

Graphite with its advantages of high thermal conductivity, low thermal expansion coefficient, and low elasticity, has been widely used as a structural material for high temperature. However, graphite can easily react with oxygen at even low temperature as 40$0^{\circ}C$, resulting in CO2 formation. In order to apply the graphite to high temperature structural material, therefore, it is necessary to improve its oxidation resistive property. Silicon Carbide (SiC) is a semiconductor material for high-temperature, radiation-resistant, and high power/high frequency electronic devices due to its excellent properties. Conventional chemical vapor deposited SiC films has also been widely used as a coating materials for structural applications because of its outstanding properties such as high thermal conductivity, high microhardness, good chemical resistant for oxidation. Therefore, SiC with similar thermal expansion coefficient as graphite is recently considered to be a g행 candidate material for protective coating operating at high temperature, corrosive, and high-wear environments. Due to large lattice mismatch (~50%), however, it was very difficult to grow thick SiC layer on graphite surface. In theis study, we have deposited thick SiC thin films on graphite substrates at temperature range of 700-85$0^{\circ}C$ using single molecular precursors by both thermal MOCVD and PEMOCVD methods for oxidation protection wear and tribological coating . Two organosilicon compounds such as diethylmethylsilane (EDMS), (Et)2SiH(CH3), and hexamethyldisilane (HMDS),(CH3)Si-Si(CH3)3, were utilized as single source precursors, and hydrogen and Ar were used as a bubbler and carrier gas. Polycrystalline cubic SiC protective layers in [110] direction were successfully grown on graphite substrates at temperature as low as 80$0^{\circ}C$ from HMDS by PEMOCVD. In the case of thermal MOCVD, on the other hand, only amorphous SiC layers were obtained with either HMDS or DMS at 85$0^{\circ}C$. We compared the difference of crystal quality and physical properties of the PEMOCVD was highly effective process in improving the characteristics of the a SiC protective layers grown by thermal MOCVD and PEMOCVD method and confirmed that PEMOCVD was highly effective process in improving the characteristics of the SiC layer properties compared to those grown by thermal MOCVD. The as-grown samples were characterized in situ with OES and RGA and ex situ with XRD, XPS, and SEM. The mechanical and oxidation-resistant properties have been checked. The optimum SiC film was obtained at 85$0^{\circ}C$ and RF power of 200W. The maximum deposition rate and microhardness are 2$mu extrm{m}$/h and 4,336kg/mm2 Hv, respectively. The hardness was strongly influenced with the stoichiometry of SiC protective layers.

• 한국식품영양과학회지
• /
• 제31권6호
• /
• pp.958-964
• /
• 2002

방사선 조사된 닭고기에서 휘발성 조사물질을 선정하기 위하여 각 선량별(0,1,3,5,10 kGy)로 조사된 닭고기를 시료로 하여 P&T법으로 휘발성 성분을 추출한 후 GC/MS법으로 분석하였으며, 동시에 LLCE법의 단점을 보완한 상보적인 분석방법으로서의 가능성을 제시하고자 하였다 그 결과 P&T/GC/MS법에 의해 총 119종의 휘발성 성분이 검출되었으며 이는 알데히드류(7종), 케톤류(22종), 알콜류(8종), 에스테르화합물류(30종), 탄화수소류(36종), 방향족화합물류(8종) 및 기타 화합물류(8종)로 구성되어 있었다. 이중 21종의 화합물이 LLCE법과 공통적으로 검출되었고, 나머지 98종은 P&T법 에 의해서만 검출됨으로서 LLCE법과 P&T법을 동시에 사용할 경우 더욱 폭넓은 휘발성 향기성분의 분석이 가능하였다. 그리고 P&T법에 의해 추출된 휘발성 향기 성분중 방사선 조사선량과 함량간의 회귀분석 및 상관분석을 행한 결과 hexene, propanol 및 1,3 bis(1,1-dimethylethy)benzene 등 3종의 휘발성 화합물이 유의적인(p<0.01 또는 p<0.05) 양의 상관성 (r)0.90)을 나타내어 P&T법에 의한 닭고기의 방사선 조사 판별을 위한 표지물질로 선정되었다.

• 한국화재소방학회논문지
• /
• 제31권2호
• /
• pp.61-73
• /
• 2017

2011년 후쿠시마 원전참사나 2001년 캘리포니아 정전사태 등은 전력관련 대형재난사고로 국가적인 막대한 손실을 가져온 발전소 안전관리의 중요성을 재조명하는 사례로 손꼽고 있다. 인간이 지구상에 살고 있는 한 전기가 없이 살 수 없는 상황에서 원자력, 석탄 및 가스 등 대용량의 위험물질을 연료로 전기를 생산하는 발전소가 안전관리의 소홀로 인한 화재폭발사고나 방사능누출, 최근 이슈가 되고 있는 지진 등 자연재해로부터 국민의 생명과 재산손실예방 및 안정적 경제성장을 위해서도 체계적인 소방안전관리의 강화노력은 절대적으로 필요하다. 따라서 본 연구에서는 국내 전력공급을 책임지고 있는 한국남부발전 등 5개 발전사 및 한수원의 소방안전관계자를 대상으로 발전소 소방안전관리 운영실태를 조사하여 분석을 수행하였으며, 그 결과, 체계적인 발전소 소방안전관리를 위해서는 소방안전경영시스템의 구축을 바탕으로 소방담당자를 위한 실효적인 업무매뉴얼 및 관리시스템의 개발과 소방안전교육의 내실화 및 지진에 대비한 내진설계의 강화를 개선방안으로 도출하였다.

• 대한기계학회논문집A
• /
• 제36권5호
• /
• pp.563-569
• /
• 2012

대용량 화력발전 보일러 과열기와 재열기 튜브는 과열에 취약하여 보일러 정지 시 튜브 내부의 산화 스케일 두께를 측정하여 과열상태를 평가한다. 산화스케일 두께측정에 의한 튜브 온도예측은 튜브의 발췌가 불가피하고 정확한 과열지점의 선정과 튜브의 초기운전온도가 확보되지 못하면 유의한 튜브온도예측결과를 얻을 수 없는 문제점이 있다. 또한 해석적 방법에 의해 튜브 온도를 예측하는 경우 튜브 외부 연소가스에 대한 연소, 복사, 대류 및 난류유동에 대한 방대한 해석이 필요한 반면 순시적인 부하의 변동, 탄종의 변화 및 운전방법의 변화를 반영할 수 없으므로 지속적인 튜브의 온도를 예측할 수 없는 단점이 있다. 본 논문에서는 보일러 운전정보와 유로망 해석을 통해 튜브의 열유속을 계산하고 이를 이용하여 단시간에 튜브의 온도를 예측할 수 있는 기법을 제시하였다. 본 기법을 Larson-Miller Parameter 법과 같은 실용적인 튜브 손상평가기법과 결합하면 유용한 고온손상감시의 수단으로 활용이 가능할 것으로 판단된다.