• 대한기계학회논문집B
• /
• 제22권3호
• /
• pp.294-302
• /
• 1998

Ignition characteristics of a vertical solid fuel plate with block have been investigated experimentally. For low radiant heat flux, ignition does not occur in a vertical solid fuel plate without block. In the case with the block on a vertical fuel plate, however, ignition can occur by increasing the residence time and the time to absorb the incident radiation flux by fuel vapor in gas phase. The ignition occurs below block and the point varies according to the block location and the block height. As the block height increases, the block locates at higher position, and the hot wall temperature increases, the ignition delay time decreases. Also as the initial temperature of fuel plate rises, the ignition delay time of the solid fuel plate decreases. The temperature distribution of solid fuel plate with block is nearly proportional to the radiant heat flux distribution. Therefore, the effect temperature by natural convection heat transfer is of the same order as that of inhibition of temperature increase by pyrolysis.

• 한국자동차공학회논문집
• /
• 제14권5호
• /
• pp.58-64
• /
• 2006

Homogeneous charge compression ignition(HCCI) combustion is an advanced technique for reducing the hazardous nitrogen oxide(NOx) and particulate matter(PM) in a diesel engine. NOx could be reduced by achieving lean homogeneous mixture resulting in combustion temperature. PM could be also reduced by eliminating fuel-rich zones which exist in conventional diesel combustion. However previous researches have reported that power-output of HCCI engine is limited by the high intensive knock and misfiring. In an attempt to extend the upper load limit for HCCI operation, supercharging in combination with Exhaust Gas Recirculation(EGR) has been applied: supercharging to increase the power density and EGR to control the combustion phase. The test was performed in a single cylinder engine operated at 1200 rpm. Boost pressures of 1.1 and 1.2 bar were applied. High EGR rates up to 45% were supplied. Most of fuel was injected at early timing to make homogeneous mixture. Small amount of fuel injection was followed near TDC to assist ignition. Results showed increasing boost pressure resulted in much higher power-output. Optimal EGR rate influenced by longer ignition delay and charge dilution simultaneously was observed.

• 한국화재소방학회논문지
• /
• 제13권1호
• /
• pp.37-47
• /
• 1999

부유중인 분진의 화재 및 용기 또는 파이프의 미세한 균열에서 비산되는 가연성 액체의 분무화재의 위험성은 착화후의 고속 확산과 높은 열방출율로 인하여 매우 높은 것으로 알려졌다. 이에 대한 연구는 주로 실험적으로나 또는 거시적인 관점의 해석으로 제한되어 왔다. 본 연구는 미시적인 관점의 해석으로서 분진 및 분무를 가연성 미세 액적으로 가정하여 그의 증발과 착화에 대하여 연구하였다. 첫 단계로서 일열의 액적 배열을 계산영역으로 하여, 비정상 이차원 보존방정식들을 적용하였다. 수치해석은 일반화된 비직교 좌표계를 사용하였고, 화학반응은 Arrhenius의 법칙에 의하여 반응속도가 제어되는 일단계 반응을 고려하였다. 계산결과는 액적 주위의 온도와 반응물질의 농도분포를 시간에 따라 보여준다. 주위의 산소가 증발하는 액적의 연료와 섞이기 시작하고 착화 조건에 다다르면, 급격한 발열반응이 예혼합된 가스로부터 일어나기 시작한다. 최대온도 영역은 점차적으로 액적 표면으로 이동하며 최대온도는 착화이후 급격히 상승한다. 연료와 산소의 농도는 최대온도 영역 근처에서 최소값을 보인다. 따라서 착화순간에는 예혼합연소의 양상을 띠는 것으로 나타났다. 이후에는 예혼합 가스의 소멸로 확산연소의 양상을 띠게 된다. 액적간의 거리는 중요한 요소로서 멀리 떨어져 있는 경우부터 액적간의 거리가 가까워지면 착화지연 시간이 줄여들어 착화가 빨리 일어나는 것으로 관찰되었다. 또한 착화 후에는 최대온도 영역이 일열의 중심선으로부터 멀어지는 것으로 나타났는데 이것은 중심부근의 산소가 먼저 소모되고 외부로부터의 산소공급도 화염에 의해 차단되어 나타나는 현상이다. 이번 연구로 미세적인 착화현상에 대한 이해를 높이게 되었고 추후 복잡한 배열에 대한 연구도 가능할 것이다.

• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.778-787
• /
• 1999

In this study, the autoignition process of liquid fuel, injected into hot and stagnant air in a 2-D axisymmetric confined cylindrical combustor, has been investigated. Eulerian-Lagrangian scheme was adopted to analyze the two-phase flow and combustion. The unsteady conservation equations were used to solve the transition of the gas field. Interactions between two phases were accounted by using the particle source in cell (PSI-Cell) model, which was used for detailed consideration of the finite rates of transports between phases. And infinite conduction model was adopted for the vaporization of droplets. The results have shown that the process of the autoignition consists of heating up of droplets, vaporization, mixing and ignition. The ignition criteria could be determined by the temporal variations of temperature, reaction rate and species mass fraction. And the effects of various parameters on ignition phenomena are examined. These have shown that the increasing the reaction rate and/or the vaporization rate can reduce the ignition delay time.

• 한국자동차공학회논문집
• /
• 제12권5호
• /
• pp.32-39
• /
• 2004

HCCI (Homogeneous Charge Compression Ignition) combustion has a great advantage in reducing NOx (Nitrogen Oxides) and PM (Particulate Matter) by lowering the combustion temperature due to spontaneous ignitions at multiple sites in a very lean combustible mixture. However, it is difficult to make a diesel-fuelled HCCI possible because of a poor vaporability of the fuel. To resolve this problem, the two-stage injection strategy was introduced to promote the ignition of the extremely early injected fuel. The compression ratio and air-fuel ratio were found to affect not only the ignition, but also control the combustion phase without a need for the intake-heating or EGR (Exhaust Gas Recirculation). The ignition timing could be controlled even at a higher compression ratio with increased IMEP (Indicated Mean Effective Pressure). The NOx (Nitrogen Oxides) emission level could be reduced by more than 90 % compared with that in a conventional DI (Direct Injection) diesel combustion mode, but the increase of PM and HC (Hydrocarbon) emissions due to over-penetration of spray still needs to be resolved.

• International Journal of Automotive Technology
• /
• 제6권6호
• /
• pp.585-590
• /
• 2005

The effects of spark timing and exhaust valve timing change on exhaust gas temperature during cold start period of an SI engine are studied through engine bench tests. The exhaust gas temperature increases when the spark timing or valve timing are retarded individually, due to late combustion or slow flame speed. Therefore, exhaust gas temperature shows a large increase when the two timings are retarded simultaneously. However, it is considered that combustion stability during cold start deteriorated under these retarded conditions. To increase exhaust gas temperature for fast warmup of catalysts while maintaining combustion stability, an optimal condition for spark and valve timing retard should be applied for the cold start period.

• 한국항공우주학회지
• /
• 제50권11호
• /
• pp.783-789
• /
• 2022

최근 연구에 의하면 하이브리드 로켓의 후연소실로 유입되는 연소유동은 고주파수 와류흘림을 포함하고 있으며, 노즐 벽면과 충돌하여 대향류가 형성되며 점화지연을 동반한 추가적인 연소가 발생하는 것이 확인되었다. 본 연구는 대향류 발생에 의한 점화지연이 연소압력 맥놀이가 나타나는 원인임을 확인하려 한다. 이를 위하여 Culick이 제안한 기존의 열음향 불안정 발생에 대한 에너지 킥 모델에 점화지연 발생을 반영한 수정 모델을 제안하였고 수치계산을 통하여 점화지연의 크기 변화가 열음향 결합에 의한 연소압력 맥놀이 발생을 결정하는 중요한 인자임을 확인하였다. 또한 후연소실 길이가 증가함에 따라 실험에서 관찰된 점화지연 감소는 에너지 킥과 압력의 위상 차의 증가를 가져와 맥놀이현상인 주기적인 압력증폭이 전혀 나타나지 않는 것도 확인하였다.

• International Journal of Automotive Technology
• /
• 제8권3호
• /
• pp.275-281
• /
• 2007

GTL (Gas To Liquid) has the potential to be used in diesel engines as a clean alternative fuel due to advantages in emission reduction, particularly soot reduction. Since the physical properties of GTL fuel differ from those of diesel fuel to some extent, studying how this difference in characteristics of GTL and diesel fuels affects spray and combustion in diesel engines is important. In this study, visual investigation of sprays and flames from GTL and diesel fuels in a vessel simulating diesel combustion was implemented. The effects of various parameters and conditions, such as injection pressure, chamber temperature and pilot injection on liquid-phase fuel length and auto-ignition delay were investigated. It was determined that GTL has a somewhat shorter liquid-phase fuel length, which explains why there is less contact between the fuel liquid-phase and flame for GTL fuel compared to diesel fuel.

• International Journal of Safety
• /
• 제3권1호
• /
• pp.20-26
• /
• 2004

The system considered in this model consists of a single, semi- transparent, diesel fuel droplet, which is immobile in the heating area and surrounded by a quiescent air. A uniform external radiation field surrounds the droplet. Results from mathematical simulation suggest that because of the higher surface temperature, the external radiative heating of the droplet can promote an earlier ignition of the fuel vapour/air mixture. The radiative heating of the droplet increases the mass transfer from the droplet to the surrounding gas-phase, thus, decreasing the heterogeneity of the fuel droplet/air system.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 1998년도 제17회 KOSCI SYMPOSIUM 논문집
• /
• pp.69-77
• /
• 1998

In order to meet the stringent emission regulations, fast light-off of a catalyst is essential to reduce the HC and CO emissions during cold start. Cranking Exhaust Gas Ignition (CEGI) method developed in this study showed that the catalyst reaches the light-off temperature in a few seconds after cold start. The CEGI system cuts off the ignition signal for a few seconds during the cranking period. so the unburned fuel-air mixture bypasses the combustion chamber and flows through the exhaust manifold. When the unburned mixture reaches two glow plugs installed upstream of the catalyst, it burns and releases the thermal energy to heat up the catalyst. Results from the FTP-75 tests showed that the exhaust emissions with the CEGI reduced by 47.7% for THC and by 88.6% for CO in the cold-transient phase of the test.