• 한국분무공학회지
• /
• 제26권3호
• /
• pp.127-134
• /
• 2021

Fire sprinkler initial spray was analyzed by Large eddy simulation (LES) and Volume of Fluid (VoF) integrated method. The IsoAdvector geometric VoF was used to identify the liquid-gas interface clearly even with the large Courant-Friedrichs-Lewy number. To reduce the computational costs, sector meshes and Adaptive Mesh Refinement up to level 3 were used. Base mesh size was 1 mm, which is roughly equivalent to the initial sprinkler droplet. Top surface radius of boss and deflector size were modified to investigate the effects of sprinkler head design on primary breakup process. When top surface radius of boss was increased, vertical liquid sheet was formed. This phenomenon reduced the sheet breakup radius, sheet thickness and velocity. Due to reduced liquid sheet thickness, a large amount of ligaments was created from the liquid sheet. As a result, there was a dramatic decrease in volume per surface area, indicating an increase in breakup process. Spray pattern viewed in radial direction also changed when top surface radius of boss increased. When top surface radius of boss was increased, a T-shaped pattern was observed while a V-shaped pattern was observed in all other cases. When the deflector size increases, the spray pattern remains V-shaped, even if the top surface radius of boss increased. Further studies on promoting atomization of the water supplied to the lower part of the sprinkler head in the T-shape pattern should be conducted.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 제26회 KOSCO SYMPOSIUM 논문집
• /
• pp.173-178
• /
• 2003

An experimental study is conducted to investigate the effects of fuel temperature on the spray characteristics of a dual-orifice type swirl injector which is used in gas turbines. The major parameters affecting spray characteristics are fuel temperature and injection pressure entering into the injector. Fuel temperature is shown to have strong influence on the spray characteristics especially at a lower temperature. In this study, fuel temperature is varied from $30^{\circ}C$ to $120^{\circ}C$ and injection pressure is altered from 3 to $7 kg_{f}$ /$cm^{2}$. Two kinds of fuel, which have different surface tension and viscosity, are chosen as an atomizing fluid. As a result, injection instability occurs in the low temperature range due to icing phenomenon and the change of fuel properties. As the injection pressure increases, the kinematic viscosity range for stable atomization becomes wider. The factor controlling the SMD of spray is substantially different depending on the fuel temperature range.

• 한국주조공학회지
• /
• 제21권3호
• /
• pp.187-191
• /
• 2001

가스분무장치를 이용하여 제조된 304 stainless steel 분말의 미세응고조직 특성을 투과전자현미경으로 관찰하였다. 분말이 sandwich 현상으로 존재하도록 구리로 전기도금한 후 tripod jig 를 이용하여 기계적 연마하여 TEM 시편을 제작하였다. 이 방법으로 제조된 TEM 시편은 넓은 지역에서 200KV 로 가속된 전자가 투과하기에 충분히 얇았으며, 작은 분말의 경우에는 분말 전체를 관찰할 수 있었다. 제한시야회절법(SADP)을 이용하여 100 ${\mu}m$ 이하 분말의 결정구조를 조사한 결과에 따르면 가스분무법으로 급냉응고된 대부분의 분말은 austenite 상으로 응고되었으며, 모든 austenite 분말은 크기에 관계없이 쌍정조직 (twinstructure)이 발견되었으며 그 밀도 역시 아주 높았다. 그러나 직경이 2 ${\mu}m$ 이하의 분말에서는 큰 과냉 (supercooling) 효과에 의하여 준결정상인 bcc 상으로 응고됨을 발견하였다.

• 한국분무공학회지
• /
• 제25권3호
• /
• pp.119-125
• /
• 2020

In this paper, we used Helmholtz solver based on 3D finite element method to quantitatively analyze the effects of change of gain, time delay and time delay spread, which are the main variables of flame transfer function, on combustion instability in gas turbine combustor. The effects of the variable of flame transfer function on the frequency and growth rate, which are the main results of combustion instability, were analyzed by applying the conventional heat release fluctuation model and modified one considering the time spread. The analysis results showed that the change of gain and time delay in the same resonance mode affected the frequency of the given resonance modes as well as growth rate of the feedback instability, however, the effect of time delay spread was not relatively remarkable, compared with the dominant effect of time delay.

• 한국자동차공학회논문집
• /
• 제7권9호
• /
• pp.56-62
• /
• 1999

The disintegration of transient diesel spray in early was investigated at different opening pressure and chamber pressure by measns of shadowgraph method using nanolite and still camera. Diesel spary was injected into the spray chamber which was charged with high pressure nitrogen gas. Atthe begining of injection, a liquid column that was almost the same diameter as the nozzle hole was observed . Spray tip penetration and spray angle were always increased with an increase in opening pressure.

• 한국분무공학회지
• /
• 제13권3호
• /
• pp.149-155
• /
• 2008

An experimental study was performed to understand spray characteristics of the rotary atomizer for the slinger combustor. In this fuel injection system, fuel is injected and atomized in the combustor by centrifugal forces to engine shaft. The experimental apparatus consists of a high speed rotational spindle, rotary atomizer, pressure tank and acrylic case. The droplet size and velocity were measured by PDPA (phase Doppler particle analyzer), and spray was visualized by using high speed camera and Nd:Yag laser-based flash photography. From the test results, the droplet size (SMD) is largely affected by rotational speed, mass flow rate and the number of orifice. As the experimental results, we could understand the spray characteristics of the rotary atomizer for the slinger combustor and obtain the optimum shape of the rotary atomizer which is suitable for the small gas turbine engine.

• 한국분무공학회지
• /
• 제1권1호
• /
• pp.28-34
• /
• 1996

Study on the mechanism of droplet transport and the droplet eddy diffusivity in the intake manifold of internal conbustion engine with carburetor has been carried out in this paper The theory and experiments were studied and performed respectively, to elucidate the mechanism and to measure typical rates of deposition, on the walls of a straight type intake manifold, of water droplets suspended in a turbulent air streams. Accordingly, the results are that Mechanism of a spray transport to the walls is caused by the fluctuation component of radial velocity. Deposition rate of a spray on the walls is mainly dependent upon air velocity and mean diameter of spray, and Droplet eddy diffusivity in the intake manifold is around $80\sim105cm^2/sec$.

• 한국분무공학회지
• /
• 제1권2호
• /
• pp.66-73
• /
• 1996

The present study investigates experimentally the characteristics of liquid jet, which is, the spray flow in the normal direction of the air stream under the flow conditions of air velocity $110\sim125m/s$. The present study adopts with the flow visualization technique using a short duration light bulb and the image processing analyse with CCD camera. Two types of injector were used: one is a flat plate type, and the other is backward facing step type, which height are 5, 8, 10mm. Dispersion of liquid jet can be represented by gray level of CCD camera. In the upstream of liquid jet, the backward facing step shows better liquid jet penetration. However, in the downstream. mean droplet size for backward facing step injector is smaller than that for flat plate injector

• 열처리공학회지
• /
• 제14권2호
• /
• pp.96-102
• /
• 2001

$Al_2O_3$-copper alloy has been successfully made by gas atomization, mechanical alloying and hot pressing. In order to investigate microstructure and phase, it has been studied by using scanning electron microscope, transmission electron microscope and X-ray diffractometor. Mechanical properties have been examined using hardness tester and compressive tester according to annealing temperature. Although comparatively large Cu-Al powders are milled, the reaction between Cu-Al and $Cu_2O$ occurs and very fine $Al_2O_3$ particles in the matrix particles (5-10nm) are obtained. Compressive strength of this alloy is more than that of GlidCop Al60.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.140-156
• /
• 1997

The combustion characteristics of DI Diesel engine using turbocharging and EGR are numerically studied. Computations are carried out for the wide range of trubochyarged pressures, EGR ratios, and Ar/He dilution. Numerical results indicate that the Ar/He dilution in the intake gas significantly influence the engine performance, the spray combustion process, and the pollutant formation.