• 제목/요약/키워드: Gas Assisted Injection Molding

검색결과 26건 처리시간 0.02초

하우징 제품의 가스사출성형에 관한 연구 (A Study on Gas-assisted Injection Molding in Housing Molded Parts)

  • 이종원
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 1999년도 춘계학술대회논문집
    • /
    • pp.131.2-135
    • /
    • 1999
  • This study focuses on part quality and cycle times under gas-assisted injection molding(GIM) of housing molded parts. The position of the gas channel was estabished near to parting line at the end of last locations to fill. Applied hot runner and valve gates the gas was introduced directly into the mold cavity via gas pin. As GIM was applied the introduced directly into the mold cavity via gas pin. As GIM was applied the conclusion reached as follows. I) The quality of appearance was improved by reducing sink marks and scratches of texture ii) The realibility was improved by preventing warpages and reinforcing rigidity through optimum gas channel layout iii)It is enable to use small size of injection molding machine step by step as GIM was accomplished low pressure and reduced clamp forces against CIM iv)The productivity were improved by reducing cycle times.

  • PDF

가스성형시 가스압력이 성형품의 강성에 미치는 영향 (The Effect of Gas Pressure on the Stiffness of Products Manufactured with Gas-Assisted Injection)

  • 박균명;박봉현;이성희;김청균
    • 한국정밀공학회지
    • /
    • 제17권10호
    • /
    • pp.102-109
    • /
    • 2000
  • In the present study, gas-assisted molding and structural vibration analysis of hollow long cylinder with the variation of gas injection pressure are performed. Though there are so many parameters such as delay time, injection pressure, and gas pressure on gas-assisted molding, the latter has the most dominant effect on this process. Therefore, the present paper deals with the effects of gas pressure on the dynamic stiffness of the model by means of vibration analysis and then suggests the fundamental materials which can be directly adapted to manufacturing lines.

  • PDF

가스사출성형을 이용한 자동차 내장부품 개발 사례에 관한 연구 (A Case Study on Development of Automotive Interior Parts using Gas Assisted Injection Molding Process)

  • 김홍석;이덕영
    • 소성∙가공
    • /
    • 제14권5호
    • /
    • pp.452-459
    • /
    • 2005
  • Gas assisted injection molding (GAIM) is an innovative low-pressure injection molding technique that can provide numerous benefits such as reduced part warpage, excellent surface quality without sink marks, low injection pressure and greater design flexibility. However, adoptions of GAIM may cause unexpected defects since it requires many subtle design factors such as resin shot size, delay time and gas injection pressure, which wouldn't be considered in conventional injection molding process. Therefore, experiences applying GAIM should be collected and examined in order to establish design rules of the new technique. The purpose of this paper is to summarize developing cases of three automotive interior parts such as instrument panel, map pocket folding and center facia side panel so that possibilities and limitations of GAIM were examined. As a result, it is necessary to consider characteristics of GAIM at the initial stage of part design in order to obtain various advantages of the GAIM process without occurring severe defects, which would increase time and cost required to the part development.

빠른 냉각과 재료절감을 위한 새로운 가스성형 프로세스 개발 (Development of New GAIM Process for Faster Cooling and Material Reduction)

  • 한성렬;박태원;곽진관;김철주;하만영;정영득
    • 한국정밀공학회:학술대회논문집
    • /
    • 한국정밀공학회 2003년도 춘계학술대회 논문집
    • /
    • pp.852-855
    • /
    • 2003
  • Gas-Assisted Injection Molding(GAIM) process, that can be used to provide a hollow shape in a molding, is a variant of the conventional injection molding process. GAIM has many advantages such as reduction of material, sink mark. warpage. and lower injection pressure. Thus, GAIM has been widely applied in the industry to make moldings with a hollow channel such as handles, TV frames and so on. On the other hand, GAIM has some disadvantages such as slow cooling time and flow marks. In the disadvantages, hot gas core causes slow cooling of a molding and the overflow. which is to prevent flow mark. is waste of materials. To solve these problems, we developed a new GAIM system that we called RGIM(Reverse Gas Injection Molding). The RGIM has two special units; one is the overflow buffer, which is used for reduction of a material, and the other tile air unit, which is used for faster cooling of a molding. We conducted an experiment and simulation to verify the efficiency of the RGIM system. Through experiments and simulation, we confirmed the effectively operating of the RGIM system and extracted the optimum process conditions.

  • PDF

가스사출시 가스흐름방향의 예측 및 제어 (Control of Gas Direction in Gas Assisted Injection Molding)

  • Soh, Young-Soo
    • 유변학
    • /
    • 제11권2호
    • /
    • pp.153-158
    • /
    • 1999
  • 가스사출시 두개이상의 가스흐름가능방향이 존재 할 때 가스는 선택적인 방향으로 흐르게는데 여기에서는 이 가스흐름 방향을 예측하는 방법을 제시하였다. 지금까지는 가스흐름방향은 가스의 하류에 있는 수지의 저항값, 즉 압력손실필요량을 비교하여 예측되어 왔는데 이방법은 대부분의 경우에 정확한 예측력을 가지고 있었다. 그러나 수지의 저항값 또는 압력손실필요량을 비교하는 방법이 실제에는 경우에따라 맞지 아니하였다. 이 연구에서는 수지속도비교가 압력손실필요량비교 보다 한단계위의 판단기준(criterion)이 되는 것을 설명하고 그예를 들어 증명 하고 있다. 압력손실필요량비교 대신 수지속도비교방법을 쓰면 예외없이 모든 경우 정확하게 가스흐름방향을 예측을 할수 있다.

  • PDF

자동차용 핸들 성형시 Gas Injection 응용 (The Application of Gas Injection Technology for the Automobile Handle Part)

  • 허영무;신광호
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2002년도 금형가공 심포지엄
    • /
    • pp.103-108
    • /
    • 2002
  • The gas injection molding technique(GIT) is a special injection molding process and has been an established and acknowledged process technique for many years. GIT has proved successful in cases where warpage has to be minimized, sink marks avoided and material input reduced. The classic field of application for GIT, however, is the production of thick-walled, rod shaped parts or hollow articles. Through this application, the handle part for automobile is molded and this part is consequently used as a insert for the additional injection molding process encapsulated with PVC.

  • PDF

Flat TV Front Cover의 Gas 사출 금형에 대한 연구 (A Study on Gas-Assisted Plastic Injection Mould of Flat TV Front Cover)

  • 문영대
    • 소성∙가공
    • /
    • 제12권8호
    • /
    • pp.738-743
    • /
    • 2003
  • The major problems of a plastic injection mould can be devided into two kinds, one is in mould another in injected parts. Most of defects of the former comes from mould design, such as, structure and working. The latter are weld line, warpage, sink mark, burning, flow mark, scratching, shading, black hole and so on. Most of problems in injection molding are difficult to find the reason because of complexity. The purpose of this paper is to improve the quality of plastic injection mould and parts with inquiring the counter plan and analizing troubles of the part of Flat TV Front Cover by flow control method and gas-assisted injection moulding. For minimizing defects of the injection moulded parts, computer aided simulation method for injection mould filling was used. Based on these numerical results, the guidelines of mould design and injection processing condition were established. As a result, the improvement of quality, such as minimizing surface defects of injection moulding parts and troubles in mould was achieved.

Flat TV Front Cover Gas 사출 금형에 대한 연구 (A Study on Gas-Assisted Plastic Injection Mould of Flat TV Front Cover)

  • 문영대
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2003년도 추계학술대회논문집
    • /
    • pp.201-206
    • /
    • 2003
  • Plastic injection mould have two kinds of trouble, one is in mould another in injection parts. Most of defects of the former take the cause in a design like in structure and working, the later weld line, transforming, sink mark, burning, flow mark, scratching, shading, black hole and so on. Most of problems of the later is difficult for making a clear definitely the reason of defects because of complexible. The purpose of this paper is to improve the quality of plastic injection mould and parts with inquiring the counter plan and rouble of the part of Flat TV Front Cover by flow control method and gas- assisted injection moulding. For minimizing defects from injection moulding parts, this paper was investigated with using computer aided injection mold filling simulations. Based on these numerical results, I established guidelines mould design and injection processing condition. As a results I got the improve of quality, minimizing surface defects moulded parts and troubles in mould.

  • PDF